This avoids cache-alignment warnings shown in console
when a usb command is entered.
Whenever X bytes of unaligned buffer is invalidated, arm core
invalidates X + Y bytes as per the cache line size and throws
these warnings.
Signed-off-by: Puneet Saxena <puneets@nvidia.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Building usb for Blackfin boards fails as we get linux/compiler.h
included which expands the "noinline" inside of the attribute and
we get attribute(attribute(noinline)).
Explicitly use the helper define to avoid this.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
A use for this is to read, modify, erase, and write an entire block as a
single unit, as a replacement for the biterr command. This way gives
more flexibility in that you can also test multiple bit errors, errors
in the ECC, etc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This field gets read in one place (by "bdinfo"), and we can replace
that with getenv("ipaddr"). After all, the bi_ip_addr field is kept
up-to-date implicitly with the value of the ipaddr env var.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
sata functions are called even if previous functions failed
because return value is not checked.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Dirk Behme <dirk.behme@de.bosch.com>
CC: Fabio Estevam <fabio.estevam@freescale.com>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lin_gadget: use common linux/compat.h
linux/compat.h: rename from linux/mtd/compat.h
lin_gadget: use common mdelay
gunzip: rename z{alloc, free} to gz{alloc, free}
fs/fat: align disk buffers on cache line to enable DMA and cache
part_dos: align disk buffers on cache line to enable DMA and cache
* 'master' of /home/wd/git/u-boot/custodians:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/85xx: don't touch MAS7 on e500v1 when relocating CCSR
powerpc/85xx: don't display address map size (32-bit vs. 36-bit) during boot
cmd_bdinfo: display the address map size (32-bit vs. 36-bit)
PowerPC: correct the SATA for p1/p2 rdb-pc platform
powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
powerpc/corenet_ds: Slave reads ENV from master when boot from SRIO
powerpc/corenet_ds: Slave uploads ucode when boot from SRIO
powerpc/corenet_ds: Slave module for boot from SRIO
powerpc/corenet_ds: Master module for boot from SRIO
powerpc/corenet_ds: Document for the boot from SRIO
powerpc/corenet_ds: Correct the compilation errors about ENV
powerpc/srio: Rewrite the struct ccsr_rio
powerpc/85xx:Fix lds for nand boot debug info
powerpc/p2041rdb: add env in NAND support
powerpc/p2041rdb: add NAND and NAND boot support
powerpc/mpc8xxx: Fix CONFIG_DDR_RAW_TIMING for two boards
powerpc/85xx:Avoid vector table compilation for nand_spl
powerpc/85xx:Fix IVORs addr after vector table relocation
powerpc/85xx:Avoid hardcoded vector address for IVORs
powerpc/p1023rds: Disable nor flash node and enable nand flash node
cmd_nand.c: In function ‘arg_off_size’:
cmd_nand.c:216:5: warning: ‘maxsize’ may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Some Freescale SOCs support 32-bit and 36-bit physical addressing, and
U-Boot must be built to enable one or the other. Add this information
to the bdinfo command.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When boot from SRIO, slave's ENV can be stored in master's memory space,
then slave can fetch the ENV through SRIO interface.
NOTE: Because the slave can not erase, write master's NOR flash by SRIO
interface, so it can not modify the ENV parameters stored in
master's NOR flash using "saveenv" or other commands.
Master needs to:
1. Put the slave's ENV into it's own memory space.
2. Set an inbound SRIO window covered slave's ENV stored in master's
memory space.
Slave needs to:
1. Set a specific TLB entry in order to fetch ucode and ENV from master.
2. Set a LAW entry with the TargetID SRIO1 or SRIO2 for ucode and ENV.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
If one command fails, 'run' command should terminate and not execute
any remaining variables.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Tested-by: Wolfgang Denk <wd@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The standalone example does not have get_timer() defined, so we cannot
rely on it being available.
Move the timer function into boootstage.c to avoid this problem.
This corrects a build breakage for the standalone example on some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: Graeme Russ <graeme.russ@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
SPI flash operations inadvertently stretching beyond the flash size will
result in a wraparound. This may be particularly dangerous when burning
u-boot, because the flash contents will be corrupted rendering the board
unusable, without any warning being issued.
So add a consistency checking so not to overflow past the flash size.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
image.c: In function ‘boot_get_ramdisk’:
image.c:800:8: warning: unused variable ‘end’ [-Wunused-variable]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
This patch allows loading RAW ramdisk via bootz command. The raw ramdisk is
loaded only in case it's size is specified:
bootz <kernel addr> <ramdisk addr>:<ramdisk size> <fdt addr>
For example:
bootz 0x42000000 0x43000000:0x12345 0x44000000
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: albert.u.boot@aribaud.net
Cc: afleming@gmail.com
Cc: Simon Glass <sjg@chromium.org>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
This command boots Linux zImage from where the zImage is loaded to. Passing
initrd and fdt is supported.
Tested on i.MX28 based DENX M28EVK
Tested on PXA270 based Voipac PXA270.
NOTE: This currently only supports ARM, but other architectures can be easily
added by defining bootz_setup().
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Warren <TWarren@nvidia.com>
Cc: albert.u.boot@aribaud.net
Cc: afleming@gmail.com,
Cc: Simon Glass <sjg@chromium.org>,
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
The following must be defined:
CONFIG_ENV_IS_IN_FAT
Enable this saving environment to FAT.
FAT_ENV_INTERFACE
Interface the FAT resides on (e.g. mmc).
FAT_ENV_DEVICE
The interface device number (e.g. 0 for mmc0)
FAT_ENV_PART
The device part (e.g. 1 for mmc0:1)
FAT_ENV_FILE
The filename of the environment file.
Author: Maximilian Schwerin <mvs@tigris.de>
Removed dead DEBUG comment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
print in the "log info" command, if "log_version = 2" also the
value from "log->v2.con".
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
If the logbuffer contains LOGBUFF_LEN chars, they never got
printed with the "log show" command, because chars get
printed with the following for loop:
for (i = 0; i < (size & LOGBUFF_MASK); i++) {
with size = LOGBUFF_LEN and LOGBUFF_MASK = (LOGBUFF_LEN-1)
for loop never executed ...
Fix this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Fixed merge conflict.
Signed-off-by: Wolfgang Denk <wd@denx.de>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
lzma: fix printf warnings
Remove CONFIG_SYS_EXTBDINFO from snapper9260.h
cmd_pxe.c: fix strict-aliasing warnings
net: smc91111: use mdelay()
doc: Fix some typos in different files
disk/part.c: Fix device enumeration through API
mkenvimage: Really set the redundant byte when applicable
mkenvimage: Don't try to detect comments in the input file
mkenvimage: Use mmap() when reading from a regular file
mkenvimage: Read/Write from/to stdin/out by default or if the filename is "-"
mkenvimage: More error handling
mkenvimage: Correct an include and add a missing one
mkenvimage: correct and clarify comments and error messages
MAKEALL: display SPL size if present
ARMV7/Vexpress: add missing get_ticks() and get_tbclk()
mkenvimage: fix usage message
cmd_fat: add FAT write command
fs/fat/fat_write.c: Fix GCC 4.6 warnings
FAT write: Fix compile errors
This adds a spl command to the u-boot.
Related config:
CONFIG_CMD_SPL
activate/deactivate the command
CONFIG_CMD_SPL_NAND_OFS
Offset in NAND to use
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Tom Rini <tom.rini@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
Without this patch, some versions of gcc (at least ELDK 4.2) complain
about dereferencing type-punned pointers.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Adds support for loading U-Boot from UART using YMODEM protocol.
If YMODEM support is enabled in SPL and the romcode indicates
that SPL loaded via UART then SPL will wait for start of a
YMODEM transfer via the console port.
Signed-off-by: Matt Porter <mporter@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Once CONFIG_FAT_WRITE is defined, users can invoke 'fatwrite' command
that saves data in RAM as a FAT file.
This patch was originally part of
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/121847
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Maximilian Schwerin <mvs@tigris.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This reverts commit 295d3942b8.
It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
This inserts bootstage calls into tftp, usb start and bootm. We
could go further, but this is a reasonable start to illustrate
the concept.
Signed-off-by: Simon Glass <sjg@chromium.org>
This defines the basics of a new boot time measurement feature. This allows
logging of very accurate time measurements as the boot proceeds, by using
an available microsecond counter.
To enable the feature, define CONFIG_BOOTSTAGE in your board config file.
Also available is CONFIG_BOOTSTAGE_REPORT which will cause a report to be
printed just before handing off to the OS.
Most IDs are not named at this stage. For that I would first like to
renumber them all.
Timer summary in microseconds:
Mark Elapsed Stage
0 0 reset
205,000 205,000 board_init_f
6,053,000 5,848,000 bootm_start
6,053,000 0 id=1
6,058,000 5,000 id=101
6,058,000 0 id=100
6,061,000 3,000 id=103
6,064,000 3,000 id=104
6,093,000 29,000 id=107
6,093,000 0 id=106
6,093,000 0 id=105
6,093,000 0 id=108
7,089,000 996,000 id=7
7,089,000 0 id=15
7,089,000 0 id=8
7,097,000 8,000 start_kernel
Signed-off-by: Simon Glass <sjg@chromium.org>
These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than the caller negating our progress numbers to indicate an
error has occurred, which seems hacky, add a function to indicate this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This changes the number 15 as used in boot_stage_progress() to use the
new name provided for it. This is a separate patch because it touches
so many files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This patch clear and disable the data cache for vxWorks.
The entry point sysInit(int) intended by Windriver to be called from
the vxWorks bootrom, a very small vxWorks system.
The routine is called by the go() handler in the bootrom, that clears
the cache from start of image to end of usable memory.
The PowerPC implementations only invalidates and disable the cache,
the ARM implementations also flush it.
U-Boot will be on the safe side, if it disables the data cache before
calling vxWorks sysInit(int).
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
boot_get_fdt() expects a uImage-wrapped FDT to be loaded to a staging
location, and then memmove()s it to the load address specified in the
header. This change enhances boot_get_fdt() to detect when the image has
already been loaded to the correct address, and skip this memmove(). The
detection algorithm was written to match the equivalent for the kernel;
see bootm_load_os()'s IH_COMP_NONE case.
v2: New patch
Signed-off-by: Stephen Warren <swarren@nvidia.com>
flush_dcache()/flush_icache() aren't defined in common.h,
flush_dcache_all()/invalidate_icache_all() however are.
Let the icache and dcache commands use those instead.
Signed-off-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Change all files in common/ to use CMD_RET_USAGE instead of calling
cmd_usage() directly. I'm not completely sure about this patch since
the code since impact is small (100 byte or so on ARM) and it might
need splitting into smaller patches. But for now here it is.
Signed-off-by: Simon Glass <sjg@chromium.org>
We currently have the same code in hush.c and main.c. This brings the
code into one place.
As an added feature, if the command function returns CMD_RET_USAGE then
cmd_process() will print a usage message for the command before
returning the standard failure code of 1.
ARM code size increases about 32 bytes with this clean-up.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a nasty interleave of #ifdefs in hush.c where the two code
paths have different indents. Remove this ickiness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Boards can select either the 'built-in' parser or the hush parser. We
should not call builtin_run_command() if we are using the hush parser.
We use run_command() instead, since it knows how to call the correct
parser.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The current run_command() is only one of the parsing options - the other
is hush. We should not call run_command() when the hush parser is being
used. So we rename this function to better explain its purpose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
It really isn't clear why this is here and there is no comment, so
drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Following the corresponding Linux code, this patch relaxes reset timings
waiting at least 100ms after power to the ports. There are some reports
that it helps make enumeration work better on some high speed devices.
Furthermore, the wait is only done once after power has been enabled
on all ports.
CC: Remy Bohmer <linux@bohmer.net>
CC: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
This moves keyboard polling logic from USB HCD drivers into USB
keyboard driver. Remove usb_event_poll() as keyboard polling was
the only user of this API. With this patch USB keyboard works with
EHCI controllers again. Tested on a tegra2 seaboard.
Signed-off-by: Allen Martin <amartin@nvidia.com>
When keys are pressed on the numeric keypad, emit key codes for the numbers,
operators, dot and enter.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
When doing a "GET_REPORT" request on the keyboard control endpoint,
the report ID should 0 (ie report ID not used) rather than 1
as reports are not used in boot mode.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
With 2a8e0fc nand_do_read_ops changed in behavior slightly (keeping in sync
with the kernel which did this change in b64d39d8) such that the OOB data is
always copied into oobbuf and never appended to datbuf. Within U-Boot only
the nand_dump function (for the dump nand subcommand) was expecting the OOB
data to only be appended to datbuf. So we now change nand_dump to not
malloc extra space, correct the comment about datbuf and OOB data and switch
the pointer to oobbuf before printing.
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The commit message of a28afca (Add uboot "fdt_high" enviroment variable)
states that fdt_high behaves similarly to the existing initrd_high.
But fdt_high actually has an outstanding difference from initrd_high.
The former specifies the start address, while the later specifies the
end address.
As fdt_high and initrd_high will likely be used together, it'd be nice
to have them behave same. The patch changes the behavior of fdt_high
to have it aligned with initrd_high.
The document of fdt_high in README is updated with an example to
demonstrate the usage of this environment variable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
* 'sf' of git://git.denx.de/u-boot-blackfin:
README: Add description of SPI Flash (SF) command configuration
sf command: allow default bus and chip selects
sf: eeprom_m95xxx: set a sane default timeout
sf: eeprom_m95xxx: fix up style
This patch allows a board configuration file to provide default bus
and chip-selects for SPI flash so that first argument to the 'sf' command
is optional.
On boards that use the mxc_spi driver and a GPIO for chip select, this allows
a much simpler command line:
U-Boot> sf probe
instead of
U-Boot> sf probe 0x5300
Tested-by: Jason Liu <jason.hui@linaro.org>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
add support for printing various clock frequency info found
in SOC such as ARM core frequency, DSP core frequency and DDR
frequency as part of bdinfo command.
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Tom Rini <trini@ti.com>
show a menu on startup instead running the shell.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jason Hobbs <jason.hobbs@calxeda.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
add the possibility to show a statusline when printing a menu
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jason Hobbs <jason.hobbs@calxeda.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
add possibility to add a timeout when reading a line
into a buffer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
When performing large bulk reads from a CD or DVD using the U-Boot
usb_storage driver, it generates requests of up to 20 blocks at a time.
With a standard 512-byte block size, that is 10240 bytes and within the
limit of U-Boot's EHCI driver (maximum 5 pages at 4k per page).
Unfortunately CD-ROM media has a 2048-byte blocksize, resulting in a
maximum transfer size of 40960 bytes, which does not fit.
Since the EHCI specification is impossibly obtuse and far beyond my
comprehension, I chose to dynamically compute the limit based on the
blocksize.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
env_get_char_spec() function is duplicated across multiple environment
files.
Remove the duplication by providing a default implementation.
Add "weak" declaration, so the default implementation can be overridden.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
* 'next' of ../next:
mkenvimage: Add version info switch (-V)
mkenvimage: Fix getopt() error handling
mkenvimage: Fix some typos
phy: add Micrel KS8721BL phy definition
net: introduce per device index
mvgbe: remove setting of ethaddr within the driver
x86: Add support for specifying an initrd with the zboot command
x86: Refactor the zboot innards so they can be reused with a vboot image
x86: Add infrastructure to extract an e820 table from the coreboot tables
x86: Add support for booting Linux using the 32 bit boot protocol
x86: Clean up the x86 zimage code in preparation to extend it
x86: Import code from coreboot's libpayload to parse the coreboot table
x86: Initial commit for running as a coreboot payload
CHECKPATCH: ./board/esd/hh405/logo_320_240_8bpp.c
CHECKPATCH: ./board/esd/hh405/logo_1024_768_8bpp.c
CHECKPATCH: ./board/esd/hh405/logo_320_240_4bpp.c
CHECKPATCH: ./board/esd/hh405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/apc405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/voh405/logo_320_240_4bpp.c
CHECKPATCH: ./board/esd/voh405/logo_640_480_24bpp.c
CHECKPATCH: ./board/esd/hh405/fpgadata.c
CHECKPATCH: ./board/esd/pci405/fpgadata.c
CHECKPATCH: ./board/esd/tasreg/fpgadata.c
CHECKPATCH: ./board/esd/apc405/fpgadata.c
CHECKPATCH: ./board/esd/voh405/fpgadata.c
CHECKPATCH: ./board/esd/ash405/fpgadata.c
CHECKPATCH: ./board/esd/dasa_sim/fpgadata.c
CHECKPATCH: ./board/esd/ar405/fpgadata_xl30.c
CHECKPATCH: ./board/esd/ar405/fpgadata.c
CHECKPATCH: ./board/esd/plu405/fpgadata.c
CHECKPATCH: ./board/esd/wuh405/fpgadata.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci405.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci405ab.c
CHECKPATCH: ./board/esd/cpci405/fpgadata_cpci4052.c
CHECKPATCH: ./board/esd/canbt/fpgadata.c
CHECKPATCH: ./board/esd/du405/fpgadata.c
CHECKPATCH: ./board/esd/cpciiser4/fpgadata.c
CHECKPATCH: ./board/dave/PPChameleonEVB/fpgadata.c
avr32:mmu.c: fix printf() length modifier
fat.c: fix printf() length modifier
cmd_sf.c: fix printf() length modifier
Make printf and vprintf safe from buffer overruns
vsprintf: Move function documentation into header file
Add safe vsnprintf and snprintf library functions
Move vsprintf functions into their own header
Conflicts:
tools/mkenvimage.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The switch to strict_strtoul() was not done correctly - this fixes
the compile error when CONFIG_CMD_TFTPPUT is active.
There appears to very little use of strict_strtoul() in commands, so
it might be easier to switch to simple_strtoul(). If not, we should
decide the best way to use strict_strtoul(). For now I have added a
friendly message which will of course increase code size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix:
cmd_pxe.c: In function 'parse_pxefile_top':
cmd_pxe.c:941:5: warning: 'err' may be used uninitialized in this
function [-Wuninitialized]
cmd_pxe.c:921:6: note: 'err' was declared here
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jason Hobbs <jason.hobbs@calxeda.com>
Acked-by: Jason Hobbs <jason.hobbs@calxeda.com>
do_env_import() missed the final '\0' terminator when calculating the
size of an environment data block. This led to an erroneous 'bad CRC,
import failed' message for a checksum protected environment (-c.)
Signed-off-by: Horst Kronstorfer <hkronsto@frequentis.com>
size_t is not always 'unsigned int', use corret length modifer.
This patch fixes following warning:
---8<---
cmd_sf.c: In function 'spi_flash_update_block':
cmd_sf.c:130: warning: format '%#x' expects type 'unsigend int', but argument 4 has type 'size_t'
cmd_sf.c:135: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'size_t'
--->8---
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
cc: Mike Frysinger <vapier@gentoo.org>
cc: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Mike Frysinger <vapier@gentoo.org>
From: Sonny Rao <sonnyrao@chromium.org>
utilize the added vscnprintf functions to avoid buffer overruns
The implementation is fairly dumb in that it doesn't detect
that the buffer is too small, but at least will not cause crashes.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
In 9792987721 Stefan describes a usecase
where the previous behavior of leaving wMaxPacketSize be unaligned
caused fatal problems. The initial fix for this problem was incomplete
however as it showed another cases of non-aligned access that previously
worked implicitly. This switches to making sure that all access of
wMaxPacketSize are done via (get|put)_unaligned.
In order to maintain a level of readability to the code in some cases
we now use a variable for the value of wMaxPacketSize and in others, a
macro.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
OpenRISC:
Tested-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Beagleboard xM, Pandaboard run-tested, s5p_goni build-tested.
Signed-off-by: Tom Rini <trini@ti.com>
We already flush the kernel image after we've loaded it to ensure
visiblity to the other cores. We need to do the same thing for the
ramdisk and device tree images. In AMP boot scenarios we might not be
HW cache coherent with the secondary core that we are loading and
setting the ramdisk and device tree up for. Thus we need to ensure
we've flushed the regions of memory utilized by ramdisk and device tree
so the loadding and any modifications (from decompression or fdt updates)
are made visible to the secondary cores.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-usb:
USB: efikamx: Enable USB on EfikaMX and EfikaSB
USB: Add generic ULPI layer and a viewport
USB: EHCI: Allow EHCI post-powerup configuration in board files
USB: mx51evk: add end enable USB host support on port 1
USB: mx53loco: add end enable USB host support on port 1
USB: MX5: Add MX5 usb post-init callback
USB: MX5: Abstract out mx51 USB pixmux configuration
USB: MX5: add generic USB EHCI support for mx51 and mx53
USB: MX5: add helper functions to enable USB clocks
usb:gadget:s5p Enable the USB Gadget framework at GONI
usb:gadget:s5p USB Device Controller (UDC) implementation
ehci: speed up initialization
usb: add help for missing start subcommand
cosmetic: remove excess whitespace from usb command help
usb: align usb_endpoint_descriptor to 16-bit boundary
usbtty: init endpoints prior to startup events
pxa: convert pxa27x_udc to use read and write functions
pxa: activate the first usb host port on pxa27x by default
pxa: fix usb host register mismatch
ehci-fsl: correct size of ehci caplength
USB: Add usb_event_poll() to get keyboards working with EHCI
USB: gadaget: add Marvell controller support
USB: Fix complaints about strict aliasing in OHCI-HCD
USB: Drop dead code from usb_kbd.c
USB: Rework usb_kbd.c
USB: Add functionality to poll the USB keyboard via control EP
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
* Support dynamic allocation of devices
* Passing data via usb device privptr
* Reorder functions to avoid forward declarations
* Introduce generic polling mechanism to fix musb and ehci-hcd breakage
due to using "extern new;" to access keyboard driver data!
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
This allows the keyboard to avoid requests via Interrupt Endpoint altogether and
run all requests via Control Endpoint. This uses the Get_Report request.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Rebased on current code.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Using mmap to allocate memory from the OS for RAM simulation we can use
u-boot own malloc implementation.
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for console output before the console is inited.
The main purpose of this is to deal with a very early panic() which would
otherwise cause a silent hang.
A new board_pre_console_putc() function is added to the board API. If
provided by the board it will be called in the event of console output
before the console is ready. This function should turn on all UARTs and
spray the character out if it possibly can.
The feature is controlled by a new CONFIG_PRE_CONSOLE_PUTC option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Graeme Russ <graeme.russ@gmail.com>
During the rebase of commit 00b7d6e "USB: Squash checkpatch warnings
in usb_kbd.c" I missed a brace, resulting in a number of build errors.
Fix these.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Rebased to current code.
Signed-off-by: Wolfgang Denk <wd@denx.de>