Commit Graph

52 Commits

Author SHA1 Message Date
Ashok Reddy Soma
702de89cc6 treewide: mem: Move mtest related defines to Kconfig
Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-05-08 12:02:56 -04:00
Tom Rini
556fd590db configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 16:15:47 -04:00
Joel Johnson
ab2f757eb0 arm: mvebu: correct SPL boot configs for SPI/MMC
Update mvebu SPL boot selection mechanism for the move to driver model
usage by ensuring that the required driver support for SPI and MMC
booting is available in SPL when the respective boot method is
selected.

Previously, all mvebu boards selected a boot method (implicitly
MVEBU_SPL_BOOT_DEVICE_SPI for many) even if SPL booting wasn't used.
This changes mvebu boot method selection to depend on SPL usage which
resolves the issue with aarch64 boards which don't use SPL getting an
implicit boot device selection resulting in unmet dependencies. The
32-bit arm boards do use SPL, but I'm led to conclude that most aren't
intentionally using the MVEBU_SPL_BOOT_DEVICE selection since none have
SPL_DM_SPI enabled in their defconfig even though they still implicitly
select the SPI boot method.

This also results in the new addition of SPL_GPIO_SUPPORT to helios4.
The mainline dts for helios4 includes the cd-gpios entry for sdhci with
identical addresses as the clearfog dts. I don't have a helios4 board
to confirm, but based on the current source conclude that the board
itself is either wired to pull the signal low for eMMC, or the default
MMC boot isn't fully functional in mainline. In either case, as far as
I can tell, including the GPIO support will at least cause no
regression.

Tested on SolidRun ClearFog devices.

Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
2020-04-22 14:28:15 +02:00
Tom Rini
052170c6a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 13:38:00 -05:00
Tom Rini
0cfccb5401 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-12-04 17:18:38 -05:00
Tom Rini
a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00
Tom Rini
8d8ee47e03 env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol
Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-20 12:24:50 -05:00
Tom Rini
0be2ecd486 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-07 17:58:06 -05:00
Tom Rini
665c35a764 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-09-23 11:47:37 -04:00
Hannes Schmelzer
1ee774d209 Convert CONFIG_SYS_SPI_U_BOOT_OFFS to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_SPI_U_BOOT_OFFS

Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
[trini: Expose this for SPL_SPI_SUNXI for now]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-25 20:59:00 -04:00
Adam Ford
1bf330150c Convert CONFIG_ARCH_CPU_INIT to Kconfig
This converts the following to Kconfig:
   CONFIG_ARCH_CPU_INIT

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
2019-08-25 19:32:55 -04:00
Tom Rini
df33f86468 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-08-14 08:11:27 -04:00
Marek Behún
6de5a717c7 arm: mvebu: turris_omnia: update defconfig
Add Macronis SPI flash support - some Omnia routers are shipped with
this SPI flash chip.
Also add the memtest command to defconfig.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-08-12 09:12:38 +02:00
Simon Glass
37304aaf60 Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_USE_PREBOOT
   CONFIG_PREBOOT

Both are together in one commit, since otherwise the former causes kconfig
to define the latter, which gives duplicate symbol errors.

Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the
backslash lands in the wrong place. Similarly with socfpga_vining_fpga.

Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-02 11:19:14 -04:00
Marek Behún
5859a39a43 arm: mvebu: turris_omnia: enable defconfig options needed by vendor
This options will be enabled by default by CZ.NIC shipped U-Boot. Enable
them in defconfig.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-03 08:18:00 +02:00
Marek Behún
fee9e83557 arm: mvebu: turris_omnia: add GPIO support to defconfig
Add support for the gpio command and driver for the I2C connected
pca9538 controller, to be able to determine if SFP module is present in
the Turris Omnia router.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-03 08:14:39 +02:00
Marek Behún
6b26f3e312 arm: mvebu: turris_omnia: move ATSHA204A from defconfig to Kconfig
This driver is required for Turris Omnia to read ethernet addresses.
Move the dependency from turris_omnia_defconfig to Kconfig.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-03 08:14:39 +02:00
Marek Behún
c91452a4a2 arm: mvebu: turris_omnia: use AHCI and SATA driver model
Enable AHCI, SCSI and SATA for compliance with the driver model
migration.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-03 08:14:39 +02:00
Marek Behún
ee7d4c5b1d arm: mvebu: turris_omnia: add XHCI to defconfig
Add XHCI_HOST and XHCI_MVEBU to defconfig, so that user's can by default
boot from USB on Turris Omnia.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-05-03 08:14:39 +02:00
Simon Goldschmidt
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing
values.

Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Tom Rini
d168bcb6fe configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 21:41:40 -04:00
Stefan Roese
5edb9b2d71 arm: mvebu: turris_omnia: Use thumb instructions in SPL to save space
With the latest changes to the drivers (SPI_FLASH_SPANSION etc), Travis
reports that the SPL image is too big. Let's use the thumb instructions
in SPL to save some space and make the image fit again.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
2019-04-26 09:16:19 +02:00
Pierre Bourdon
61b8c34e86 arm: mvebu: turris_omnia: use MMC driver model
Enable DM_MMC for compliance with the driver model migration.

Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-26 07:35:38 +02:00
Baruch Siach
c1d81f6f01 arm: mvebu: turris_omnia: select Kconfig SPI_FLASH_SPANSION
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
2019-04-12 07:04:18 +02:00
Patrick Delaunay
abe66b1b5d Convert CONFIG_ENV_SPI_* to Kconfig
This converts the following to Kconfig:
  CONFIG_ENV_SPI_BUS
  CONFIG_ENV_SPI_CS
  CONFIG_ENV_SPI_MAX_HZ
  CONFIG_ENV_SPI_MODE

Most of time these value are not needed, CONFIG_SF_DEFAULT
with same value is used, so I introduced CONFIG_USE_ENV_SPI_*
to force the associated value for the environment.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
2019-03-25 17:36:59 -04:00
Tom Rini
50e24381c0 Merge branch 'master' of git://git.denx.de/u-boot-spi
- SPI-NOR support
2019-02-07 14:48:56 -05:00
Vignesh R
ea4805d6b2 configs: Move CONFIG_SPI_FLASH into defconfigs
Completely move CONFIG_SPI_FLASH from remaining board header files to
defconfigs

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
2019-02-07 15:33:21 +05:30
Stefan Roese
94f453ea38 pci: pci_mvebu: Add DM_PCI support and move CONFIG_PCI_MVEBU to defconfig
This patch adds DM_PCI support to the MVEBU PCIe driver. This is
necessary, since all PCI drivers have to be moved to DM (driver model)
until the v2019.07 release.

To not break git bisect'ablility, this patch also moves CONFIG_PCI_MVEBU
from config headers to the defconfig files.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: VlaoMao <vlaomao@gmail.com>
2019-02-05 14:22:38 +01:00
Tom Rini
1bac199e8c configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2019-01-07 18:11:00 -05:00
Tom Rini
8c5cad05c9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-09-03 15:26:12 -04:00
Adam Ford
8ccf98b1cf Convert CONFIG_MISC_INIT_R to Kconfig
This converts the following to Kconfig:
   CONFIG_MISC_INIT_R

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-17 13:04:00 -04:00
Adam Ford
d7869b2183 Convert CONFIG_MII et al to Kconfig
This converts the following to Kconfig:
   CONFIG_MII
   CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-08-17 13:03:54 -04:00
Tom Rini
86cf1c8285 configs: Migrate CONFIG_NR_DRAM_BANKS
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-08-16 16:45:02 -04:00
Tom Rini
358b6a20e4 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-06-04 11:57:37 -04:00
Mario Six
a8ca5c8adb treewide: Move CONFIG_PHY_MARVELL to Kconfig
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards
already had it in their Kconfig), but had not been moved for older
boards.

Move it to the defconfigs for all boards.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-05-14 21:28:38 -04:00
Marek Vasut
555004381e spl: spi: Move CONFIG_SPL_SPI_LOAD to Kconfig
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.

Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
2018-04-11 13:22:00 -04:00
Mario Six
78eba69d98 treewide: Migrate CONFIG_DISPLAY_BOARDINFO_LATE to Kconfig
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.

Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-08 15:12:09 -04:00
Tom Rini
c9542eae0b configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-07 20:37:13 -04:00
Tuomas Tynkkynen
4a942f49b8 spi: Migrate CONFIG_KIRKWOOD_SPI to Kconfig
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
2018-02-13 23:01:44 -05:00
Tom Rini
278b90ce78 configs: Migrate CONFIG_SYS_TEXT_BASE
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-02-11 09:30:09 -05:00
Tuomas Tynkkynen
9fd95ef0d3 ata: Migrate CONFIG_SCSI_AHCI to Kconfig
And use 'imply' liberally.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-12-12 18:13:19 -05:00
Tuomas Tynkkynen
ad12dc1844 cmd: Toggle the default value of CONFIG_CMD_IMLS
Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
2017-10-10 17:51:04 -04:00
Marek Behún
32c778637b mvebu: turris_omnia: Add CONFIG_CMD_BTRFS to defconfig
Signed-off-by: Marek Behun <marek.behun@nic.cz>
2017-10-02 21:52:19 -04:00
Chris Packham
7654f62f4e ARM: mvebu: Convert CONFIG_MVNETA to Kconfig
This converts the following to Kconfig:
   CONFIG_MVNETA

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
2017-09-26 06:51:30 +02:00
Tom Rini
5dc4dfd2a9 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-28 07:16:32 -04:00
Tom Rini
88663126a0 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-14 20:00:40 -04:00
Simon Glass
6500ec7a5a Convert CONFIG_CMD_PCI to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:50 -04:00
Tom Rini
1989374b21 configs: Finish migration of PHY_GIGE
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-08 17:02:31 -04:00
Alexandru Gagniuc
3146f0c017 Move PHYLIB to Kconfig
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2017-08-07 15:22:28 -05:00
Simon Glass
91c868fe7c Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig
This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_SPI_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-07-25 21:31:03 -04:00