CPLD 2.0 provides a new register which bit[0] is set to '1' will reset
board with initializing the CPLD registers to default values. And add
bit[6] of register at offset 0x5 to use to enable flash bank selection.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update MPC8349EMDS to use unified DDR driver instead of spd_sdram.c.
The unified driver can initialize data using DDR controller. No need to
use DMA if just to initialze for ECC.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2041RDB has almost identical setup for TLB, LAWS, and PCI with
other P-Series CoreNet platforms.
The only difference between P2041RDB & P3041DS/P4080DS/P5020DS is the
CPLD vs PIXIS FPGA which we can handle via some simple #ifdefs in the
TLB and LAW setup tables.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We currently support 4 SoC/Boards from the P-Series of QorIQ SoCs that
are based on the 'CoreNet' Architecture: P2041RDB, P3041DS, P4080DS, and
P5020DS. There is a significant amount of commonality shared between
these boards that we can refactor into common code:
* Initial LAW setup
* Initial TLB setup
* PCI setup
We start by moving the shared code between P3041DS, P4080DS, and P5020DS
into a common directory to be shared with other P-Series CoreNet boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
RDIMM has different timing parameters from UDIMM. Create new tables for
RDIMMs. Single-, dual- and quad-rank RDIMMs have been verified with speeds
from 800 to 1333MT/s. Speed table expands to include 1600MT/s for future
use. Single- and quad-rank RDIMM entries are copied into UDIMM tables for
future use.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII and XAUI Ethernet on P2041RDB board.
The five dTSEC can be routed to two on-board RGMII phy, three on-board
SGMII phy or four SGMII phy on SGMII riser card according to different
serdes protocol configuration and board lane configuration. Also updated
the device tree to direct the Fmac MAC to the correct PHY.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P3041DS &
P5020DS ("Hydra").
The lane_to_slot[] array is initialized dynamically, since board switches
can be used to control the muxing of SERDES lanes to slots.
The BRDCFG1 PIXIS register is used to route the MII bus to the appropriate
slot. The SERDES configuration is queried to help determine the routing
between MACs and slot/phy combination.
If a XAUI card is inserted, muxing for that card is enabled and never
turned off. The PHY address for the 10G XAUI card depends on the slot in
which it's inserted. If it's in slot 1, the address is 4. If it's in
slot 2, the address is 0.
Update the MDIO routing in the P3041DS and P5020DS device trees based on
the board-level muxing. The SERDES configuration determines which
SGMII/XGMII boards are located in which slots, and so the MDIO bus needs
to be muxed correctly whenever talking to a PHY connected to any Fman MAC.
The Fman Ethernet nodes in the device tree also need to be routed to the
correct PHYs.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for RGMII, SGMII, and XAUI (10Gb) Ethernet on P4080DS.
The board supports add-on cards for SGMII and XAUI functionality. Which
slots on the board these cards are in is a function of the SERDES option
selected and muxes on the board.
Additionally because of the high-configurablity which MDIO bus one is
connected to is "selected" via an FPGA register. We create dummy MDIO
bus for the phy layer and hide the mux manipulation in this dummy layer.
Add fman fdt helper function in board common code it'll be used by several
freescale boards that do various muxing of the MDIO signals based on which
controller/interface one is trying to talk to.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove unnecessary or dead code/includes.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We shouldn't be setting execute permissions on TLB entries that will not
actually have any code run from them.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Boot methods supported: NOR Flash, SPI Flash and SDCARD
This patch adds the following basic interfaces:
DDR3, eTSEC, DUART, I2C, SD/MMC, USB, SATA, PCIe, NOR Flash, SPI Flash.
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
Local Bus (IFC):
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
64KB CPLD device(GPCM interface)
SPI Flash:
128 Mbit SPI Flash memory
SD/MMC:
connector to interface with the SD memory card
SATA:
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0:
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC:
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221
eCAN:
Two DB-9 female connectors for Field bus interface
UART:
supports two UARTs up to 115200 bps for console
TDM:
2 FXS ports connected via an external SLIC to the TDM interface.
SLIC:
SPI SLIC
I2C:
Serial EEprom
Real time clock
256 Kbit M24256 I2C EEPROM
PCIe:
PCIe and mPCIe connectors.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The following boards share a common design but with minor variations
between them:
P1020MSBG-PC
P1020RDB-PC
P1020UTM-PC
P1021RDB-PC
P1024RDB
P1025RDB
P2020RDB-PC
The P1020RDB-PC shares its roots in the existing P1020RDB board design,
however uses DDR3 instead of DDR2.
P2020RDB-PC differs from the P102x RDB-PC with 64-bit DDR and 100Mhz SYSCLK.
Key features on these boards include:
* DDR3
* NOR flash
* NAND flash (on RDB's only)
* SPI flash (on RDB's only)
* SDHC/MMC card slot
* VSC7385 Ethernet switch (on P1020MBG, P1020RDB, & P1021RDB)
* PCIE slot and mini-PCIE slots
As these boards use soldered DDR chips not regular DIMMs, an on-board EEPROM
is used to store SPD data. In case of absent or corrupted SPD, falling back
to timing data embedded in the source code will be used. Raw timing data is
extracted from DDR chip datasheet. Different speeds of DDR are supported
with this approach. ODT option is forced to fit this set of boards, again
because they don't have regular DIMMs.
CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS is defined as 5ms to meet
specification for writing timing.
VSC firmware Address is defined by default in config file for eTSEC1.
SD width is based off DIP switch. DIP switch is detected on the
board by reading i2c bus and setting the appropriate mux values.
Some boards have QE module in the silicon (P1021 and P1025). QE and eLBC
have pins multiplexing. QE function needs to be disabled to access Nor Flash
and CPLD. QE-UEC and QE-UART can be enabled for linux kernel by setting "qe"
in hwconfig. In addition, QE-UEC and QE-TDM also have pins multiplexing, to
enable QE-TDM for linux kernel, set "qe;tdm" in hwconfig. Syntax is as below
'setenv hwconfig qe' to enable QE UEC/UART and disable Nor-Flash/CPLD.
'setenv hwconfig 'qe;tdm'' to enalbe QE TDM and disable Nor-Flash/CPLD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Zhao Chenhui <b26998@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Tang Yuantian <b29983@freescale.com>
Signed-off-by: ramneek.mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Akhil Goyal <akhil.goyal@freescale.com>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The function fsl_setup_hose clears the variable pci1_hose.
Set pci1_hose.config_table after it.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
The dram initialization sequence should be in order.
This patch add mb for the dram intialization code to make
sure the compiler do not disorder the code.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Introduce the --gc-sections for ColdFire platform and clean up the
corresponding lds file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Updated mx53 ddr3 script in order to align with the latest Freescale version from July 8, 2011:
-change ESDREF[REF_SEL]=01 (for 32KHz), from incorrect setting of 00 (64KHz)
-change DDR3 MR0 write to "setmem /32 0x63fd901c = 0x052080b0" from
"0x092080b0". This changes write recovery from 8 clocks to 6 clocks
(in line with ESDCFG1[tWR])
Signed-off-by: Lily Zhang <r58066@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The SHARP LQ084S3LG01 is a TFT LCD used on the P1022DS (revision "C") board.
This device only supports 800x600 resolution, so if that resolution is selected,
assume that this is the device. The device is attached to the LVDS port
on the P1022DS board.
The existing 800x600 entry (for the PDM360NG board) is actually 800x480,
so we fix that. To support two different 800x resolutions, the Y-resolution
is now passed to fsl_diu_init() and both values are used to pick the proper
fb_videomode structure.
The data for the 800x600 video mode is originally from Jiang Yutang.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Jiang Yutang <b14898@freescale.com>
to make USB2 worked in gadget mode, we need to set it's 'dr_mode' to
'peripheral' in hwconfig, but driver starts scan from 'usb1', it'll break
out if it cannot find 'usb1', so drop the 'else' clause to make driver scan
all the 'usbx'.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Current code would print RAM size information like this:
DRAM: DDR: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Turn a number of printf()s into debug() to get rid of the redundant
"DDR: " string like this:
DRAM: 256 MiB (DDR1, 64-bit, CL=2, ECC off)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.
Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: MX5: Fix broken leftover TO-2 errata workaround
MX31: Cleanup clock function
scb9328: Add ARM relocation support
am3517evm: change console device from ttyS2 to ttyO2
Remove volatile qualifier in get_ram_size() calls
TI: TNETV107X Fix Build Error
ARM: add missing CONFIG_SKIP_LOWLEVEL_INIT for armv7
arm: add CONFIG_MACH_TYPE setting and documentation
arm: add __ilog2 function
Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
EfikaMX: Enable EXT2 booting
EfikaMX: Add missing CONFIG_SYS_TEXT_BASE
EfikaMX: Use correct imximage.cfg
MX27: Update to autogenerated asm-offsets.h
MX5: Update to autogenerated asm-offsets.h
imx: Add support for zmx25 board
imx: Make imx25 compatible to mxc_gpio driver and fix in tx25
imx: Add auto generation of asm-offsets.h for imx25
imx: Add support for USB EHCI on imx25
imx: Use correct imx25 reset.c
imx: Add get_tbclk() function for imx25
ARM: Update maintainer of board scb9328
mx27: Make the UART port number explicit
build: Add targets for auto gen of asm-offsets.h and use it in imx35
mx31pdk: cosmetic: Fix line over 80 characters
P2041RDB Specification:
-----------------------
Memory subsystem:
* 4Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
* 128 Mbyte NOR flash single-chip memory
* 256 Kbit M24256 I2C EEPROM
* 16 Mbyte SPI memory
* SD connector to interface with the SD memory card
Ethernet:
* dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
* dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
* dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
PCIe:
* Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
* Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
I2C:
* I2C1: Real time clock, Temperature sensor, Memory module
* I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM, PCIe slot1/2
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Resolve P1020 second USB controller multiplexing with eLBC
- mandatory to mention USB2 in hwconfig string to select it
over eLBC, otherwise USB2 node is removed
- works only for SPI and SD boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023RDS board is the reference board for the P1023 SoC.
Add support for booting it from NOR or NAND, with fixed 2G of DDR, PCIe,
UART, I2C, etc.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If DDR initialziation uses a speed table and the speed is not matched,
print a warning message instead of silently ignoring.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Allow overriding RCW for all RDIMM, not only quad-rank ones.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection in LAW & TLB code to handle the case in which
CONFIG_SYS_BMAN_MEM_PHYS or CONFIG_SYS_QMAN_MEM_PHYS arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove an empty board_early_init_f() from the MPC8323ERD and MPC360ERDK boards.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The clock-frequency property in an audio codec's device tree node is set to
the input clock frequency for that codec. On the Freescale P1022DS board,
the input clock is enabled only if the hwconfig 'audclk' option is set.
Therefore, the property should only be set in the device tree if the clock
is actually enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes the MX31ADS build by using the new relocation scheme.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Felix Radensky <felix@embedded-sol.com>
