Explain how to flash the eMMC and how to boot from it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register
to avoid the voltage peak issue while we do the IEEE PHY comformance test
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Add the delay (10ms) to ensure the clock is stable and to meet the clock-to-reset(1ms) requirement recommended in the AR8033 datasheet
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Change the PMIC bulk configuration from auto mode to sync mode to avoid the voltage shutdown issue
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Add the configuration options for display initialization in case we need to
do the display initialization in kernel to support different timing settings
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. So needs to enable them together.
DM FEC and SPI are not enabled, but they use gpio in board code.
So use gpio_request first to request the gpio, because DM_GPIO
is enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Use device-tree fixup to communicate the MTD partitions to the
kernel. Remove mtdparts from the kernel command line.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Implement board level USB PHY mode callback. On USB OTG Port 1
the Colibri standard foresees GPIO USBC_DET to decide whether the
port should run in Host or Device mode.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This includes support for rk3188 from Heiko Stübner and and rk3328 from
Kever Yang. Also included is SPL support for rk3399 and a fix for
rk3288 to get it booting again (spl_early_init()).
Before clock driver availability it was required to enable usart1 clock
for serial init but now with clock driver is taking care of usart1 clock.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This patch adds device tree support for stm32f7 serial driver & removes serial
platform data structure.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for TQMa6DL using i.MX6DL and 1GiB DRAM
Since The module will use the same devicetree, we patch
the ram size in ft_board_setup.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
We have a Kconfig name for the module types. Let's Use it.
Some feature selections and configurations are based on the
module. Module selection selects the CPU type.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot based
on the bootdevice so-that conditional macros for MMC via
CONFIG_BOOTCOMMAND should be avoided in config files.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot from eMMC:
--------------
U-Boot SPL 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21)
Trying to boot from MMC2
U-Boot 2017.01-00318-g8e243f8 (Jan 26 2017 - 11:53:21 +0100)
CPU: Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
switch to partitions #0, OK
mmc1(part 0) is current device
Net: No ethernet found.
Hit any key to stop autoboot: 0
Booting from mmc ...
switch to partitions #0, OK
mmc1(part 0) is current device
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since the CS are not in use, do not map them. User of starterkit
mainboard is free to use them otherwise. When using these pins later
in the OS for instance as GPIO IRQ pin, they need to be input.
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
The current driver stength is too high, leading to spec violations
on the falling edge. Fix it with values from HW
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add board_mmc_get_env_dev
Switch the mmc env based on the mmc devno, instead of separately
defining a config item in include/configs using board_mmc_get_env_dev
- devno 0: sd/esd
- devno 1: mmc/emmc
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL mmc device index is get based on the boot device, like
- BOOT_DEVICE_MMC1 for mmc device 0
- BOOT_DEVICE_MMC2 for mmc device 1
Currently BOOT_DEVICE_MMC1 is setting both SD/eSD and MMC/eMMC
boot devices in i.MX, So u-boot is loading from mmc device 0 even
"if the board booting from SD/eSD or MMC/eMMC"
So, this patch set BOOT_DEVICE_MMC2 for MMC/eMMC so for MMC/eMMC
the u-boot is loading from mmc device 1 and the board file need to
take care if the board have different mmc device order intialization.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
