DaVinci EMAC is found not only on DaVinci SoCs but on some OMAP3 SoCs
also. This patch moves common defines from arch-davinci/emac_defs.h to
drivers/net/davinci_emac.h
DaVinci specific PHY drivers hacked to include the new header. We might
want to switch to phylib in future.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
s3c64xx.c implemented its own nand_read_byte, nand_write_buf and
nand_read_buf functions. This provoked a regression when these functions
were made public by patch 55f429bb39614a16b1bacc9a8bea9ac01a60bfc8.
This deletes these duplicated functions from s3c64xx.c and adds the generic
implementations in nand_base.c to the spl Makefile. It also adds
-ffcuntion-sections and -gc-sections to the compilation flags of the SPL to
avoid errors originating from unused functions in nand_base.c.
Description of the regression:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/108873
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Functions often used in SPL are now part of linux/mtd/nand.h.
Static modifiers are removed from these functions in
drivers/mtd/nand/nand_base.c.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Cc: scottwood@freescale.com
Cc: s-paulraj@ti.com
Cc: albert.u.boot@aribaud.net
Acked-by: Scott Wood <scottwood@freescale.com>
Consider that ide_preinit() succeed if at least one port is successfully
initialized. This allows to iniatialize IDE support on a board with two
SATA ports but a single hard disk available.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
FTPCI100 is a SoC PCI componenet of Faraday company.
Which is usually built into SoC chips for providing
embedded PCI functions.
Signed-off-by: Gavin Guo <gavinguo@andestech.com>
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
This adds support for the SMSC LAN87xx PHYs.
Following PHYs can be used by set CONFIG_PHY_SMSC to config.
- SMSC LAN8700
- SMSC LAN8710/LAN8720
- SMSC LAN8710/LAN8720
A setup of PHY was copied from linux kenrel.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Fixed white space errors; modified commit message a bit.
Signed-off-by: Wolfgang Denk <wd@denx.de>
When printing the string "\r\n" to the framebuffer console, the first
character of the current line was being replaced with a space. The "boot"
prompt would become the "oot" prompt. This change makes the cursor
non-destructive so that no matter where it goes on its way to where it's
supposed to be, the end result is that the cursor is where it's supposed to
be with the other text preserved.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The original m88e1111s_config() does not do the SGMII mode
initialization and is buggy. Rewrite the function according to
3.0.6 kernel function m88e1111_config_init() in drivers/net/phy/marvell.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
We want to show the length, so multiplying by sector size makes no sense.
This is a hold over from the erase code before the big refactor.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The sh_eth driver had an own mii functions. However the function
didn't support the gigabit PHY. The U-Boot has the general phy driver
and miiphybb driver, and they already support it.
So this patch removes the own functions and uses the phy driver.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix:
sl811-hcd.c: In function 'sl811_rh_submit_urb':
sl811-hcd.c:556:8: warning: variable 'wIndex' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Fix:
sata_dwc.c: In function 'scan_sata':
sata_dwc.c:535:38: warning: variable 'udma_mask' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kazuaki Ichinohe <kazuichi@fsi.co.jp>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
mpc85xx: support for Freescale COM Express P2020
arch/powerpc/cpu/mpc8xxx/ddr/interactive.c: Fix GCC 4.6 build warning
mpc85xx: support board-specific reset function
powerpc/85xx: verify the localbus device tree address before booting the OS
mpc8xxx: update module_type values from JEDEC DDR3 SPD Specification
powerpc/p3060qds: Add board related support for P3060QDS platform
powerpc/85xx: clean up and document the QE/FMAN microcode macros
powerpc/85xx: always implement the work-around for Erratum SATA_A001
powerpc/85xx: CONFIG_FSL_SATA_V2 should be defined in config_mpc85xx.h
powerpc/85xx: Add workaround for erratum A-003474
powerpc/85xx: fixup flexcan device tree clock-frequency
powerpc/85xx: Add workaround for erratum CPU-A003999
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman. Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both. A given SOC will only have
a QE or an Fman, so this is safe.
Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND. There's no way to know by looking at a variable how it's supposed
to be used.
In the future, the code which uploads QE firmware and Fman firmware will
be merged.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default. So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If no controller is present, the i8402 driver should return immediately and
not attempt to operate on the missing hardware.
In kbd_input_empty, the status register is checked every millisecond to see
whether the input buffer is empty, up to a timeout which is tracked by
decrimenting a counter each time the check is performed. The decrement is
performed with a postfix -- operator, and the value of the counter is
checked in place. That means that when the counter reaches zero and the
loop terminates, it will actually be decrimented one more time and become
-1. That value is returned as the return value of the function. That would
give the right answer if it wasn't for that extra decrement because a
timeout would indicate that the buffer never became empty.
This change fixes both of those bugs.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Change my old email address which is no longer valid.
Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 'master' of git://git.denx.de/u-boot-mmc:
Revert "mmc: retry the cmd8 to meet 74 clocks requirement in the spec"
mmc: mv_sdhci: Fix host version read for Armada100
Fix:
x86emu/ops2.c: In function 'x86emuOp2_set_byte':
x86emu/ops2.c:171:11: warning: variable 'name' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 02f3029f18.
This patch add 3 times retry to CMD8 because the Marvell mmc controller
doesn't obey the power ramp up process in the SD specification 6.4.1.
(Please refer to figure 6.1 and 6.2 in the specification.)
The CMD0 should be send after power ramp up has been finished.
However, the Marvell mmc contorller must do power ramp up after the
first CMD0 command has been send.
This patch also affect existing platforms like Nokia N900 and other
platforms.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Acked-by: Lei Wen <leiwen@marvell.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
sdhci_readw does not work for host version read in Armada100 series
SoCs. This patch fix this issue by making a sdhci_readl call to get host
version.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Add the 1920x1080 and 1280x720 resolution support.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
CC: Anatolij Gustschin <agust@denx.de>
Fix:
davinci_i2c.c: In function 'flush_rx':
davinci_i2c.c:81:6: warning: variable 'dummy' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This supports I2C of Renesas SH.
I tested on SH7724.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Heiko Schocher <hs@denx.de>
Fix:
cs8900.c: In function 'get_reg_init_bus':
cs8900.c:69:14: warning: variable 'c' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
lan91c96.c: In function 'dump_memory_info':
lan91c96.c:157:7: warning: variable 'mem_info' set but not used
[-Wunused-but-set-variable]
lan91c96.c: In function 'smc_send_packet':
lan91c96.c:320:16: warning: variable 'ioaddr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
samsung.c: In function 's3c_onenand_check_lock_status':
samsung.c:486:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
musb_hcd.c: In function 'submit_control_msg':
musb_hcd.c:851:6: warning: variable 'csr' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
device is already in *normal* (D0) mode => it doesn't need to be wake-up.
With this patch, we only wake-up (writing on TEST_BYTE register) if PM_MODE
bits of PM_CTRL register is in sleep (D1/D2) mode.
Signed-off-by: Bertrand Cachet <bertrand.cachet@heig-vd.ch>
No one uses this driver, and it isn't converted to the NET_MULTI
framework (which we dropped recently), so drop this driver too.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
Commit 79ad544009 broke MAC address
programming in the SMSC95xx register set.
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Simon Glass <sjg@chromium.org>
* 'master' of git://git.denx.de/u-boot-nds32:
nds32/lib: add ide generic support
nds32: enhance io.h for compatibility with periphals
ftide020: fix incorrect information display format
* 'master' of git://git.denx.de/u-boot-nios:
nios2: Offer ft_board_setup() capability and call fdt_fixup_ethernet().
board/nios2-generic: Use altera_pio driver and remove board specific driver
gpio: Add driver for Altera's PIO core
nios2: Pseudo implement dcache_status/enable/disable()
Fix the following build warning in drivers/net/e1000.c
e1000.c: In function 'e1000_reset_hw':
e1000.c:1373:11: warning: variable 'icr' set but not used [-Wunused-but-set-variable]
e1000.c: In function 'e1000_phy_init_script':
e1000.c:4395:11: warning: variable 'ret_val' set but not used [-Wunused-but-set-variable]
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Fix:
s3c24x0_rtc.c: In function 'rtc_get':
s3c24x0_rtc.c:67:53: warning: variable 'a_armed' set but not used
s3c24x0_rtc.c:67:45: warning: variable 'a_year' set but not used
s3c24x0_rtc.c:67:38: warning: variable 'a_mon' set but not used
s3c24x0_rtc.c:67:30: warning: variable 'a_date' set but not used
s3c24x0_rtc.c:67:22: warning: variable 'a_hour' set but not used
s3c24x0_rtc.c:67:15: warning: variable 'a_min' set but not used
s3c24x0_rtc.c:67:8: warning: variable 'a_sec' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
bus_vcxk.c: In function 'vcxk_display_bitmap':
bus_vcxk.c:396:16: warning: variable 'compression' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
da8xx-fb.c: In function 'video_hw_init':
da8xx-fb.c:688:6: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
enc28j60.c: In function 'enc_receive':
enc28j60.c:435:5: warning: variable 'eir_reg' set but not used
[-Wunused-but-set-variable]
enc28j60.c: In function 'enc_poll':
enc28j60.c:503:5: warning: variable 'estat_reg' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
at91_emac.c: In function 'at91emac_write_hwaddr':
at91_emac.c:477:15: warning: variable 'dev' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
dataflash.c: In function 'AT91F_DataflashInit':
dataflash.c:42:6: warning: variable 'last_part' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
atmel_spi.c: In function 'spi_xfer':
atmel_spi.c:139:7: warning: variable 'ret' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
sata_dwc.c: In function 'sata_dwc_softreset':
sata_dwc.c:444:5: warning: variable 'status' set but not used [-Wunused-but-set-variable]
sata_dwc.c:443:6: warning: variable 'serror' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'scan_sata':
sata_dwc.c:654:16: warning: variable 'lba_desc' set but not used [-Wunused-but-set-variable]
sata_dwc.c:538:16: warning: variable 'xfer_mask' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_read_id':
sata_dwc.c:747:14: warning: variable 'reason' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_read_sectors':
sata_dwc.c:1810:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
sata_dwc.c: In function 'ata_dev_write_sectors':
sata_dwc.c:1994:6: warning: variable 'rc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Stefan Roese <sr@denx.de>
Fix:
4xx_enet.c: In function 'ppc_4xx_eth_init':
4xx_enet.c:875:6: warning: variable 'ethgroup' set but not used [-Wunused-but-set-variable]
I used "__maybe_unused" here intentionally, since all other
alternatives to fix this compilation warning would result in more
ifdef's.
Signed-off-by: Stefan Roese <sr@denx.de>
Convert custom debug code to use standard debug() facility.
This also fixes these build warning:
ct69000.c: In function 'FindAndSetPllParamIntoXrRegs':
ct69000.c:706:28: warning: variable 'new_pixclock' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
Fix:
sym53c8xx.c: In function 'scsi_write_dsp':
sym53c8xx.c:456:16: warning: variable 'val' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix:
x86emu/ops.c: In function 'x86emuOp_int3':
x86emu/ops.c:3521:9: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
x86emu/ops.c: In function 'x86emuOp_int_IMM':
x86emu/ops.c:3549:9: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
x86emu/ops.c: In function 'x86emuOp_into':
x86emu/ops.c:3579:9: warning: variable 'tmp' set but not used [-Wunused-but-set-variable]
x86emu/ops.c: In function 'x86emuOp_aad':
x86emu/ops.c:3993:8: warning: variable 'a' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
ahci.c: In function 'ata_scsiop_read10':
ahci.c:564:6: warning: variable 'lba' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
davinci_mmc.c: In function 'dmmc_wait_fifo_status':
davinci_mmc.c:72:7: warning: variable 'mmcstatus1' set but not used [-Wunused-but-set-variable]
davinci_mmc.c: In function 'dmmc_busy_wait':
davinci_mmc.c:89:7: warning: variable 'mmcstatus1' set but not used [-Wunused-but-set-variable]
Delete the unused variable.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Fix:
ivm_core.c: In function 'ispVMLCOUNT':
ivm_core.c:2105:16: warning: unused variable 'usByte'
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Wolfgang Denk <wd@denx.de>
* 'master' of git://git.denx.de/u-boot-video:
api: export LCD device to external apps
font: split font data from video_font.h
tools: logo: split bmp arrays from bmp_logo.h
lcd: add clear and draw bitmap declaration
VIDEO: mx3fb: GCC4.6 fix build warnings
Powerpc/DIU: Fixed the 800x600 and 1024x768 resolution bug
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
While video_font.h is useful even without referencing the font data, it
is not possible to be included multiple times because it defines font
data array right in the header.
This patch splits the font data array into video_font_data.h and so now
video_font.h can be included multiple times. This at least solves the
code duplication in board/mcc200/lcd.c.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The generated header bmp_logo.h is useful even outside common/lcd.c for
the logo dimension. However, the problem is, the generated bmp_logo.h
cannot be included multiple times because bmp_logo_palette[] and
bmp_logo_bitmap[] are defined in the bmp_logo.h.
This patch fixes this by defining these arrays in another header
bmp_logo_data.h and in bmp_logo.h only declaring these arrays.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
since commits:
davinci: emac: add support for more than 1 PHYs
062fe7d332
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
fb1d6332b5
I get following warning on the enbw_cmc board:
Err: serial
Net: 5 ETH PHY detected
miiphy_register: non unique device name 'KSZ8873 @ 0x01'
DaVinci-EMAC
Hit any key to stop autoboot: 0
Also I see some debug printfs:
=> run load
+ emac_close
+ emac_ch_teardown
- emac_ch_teardown
+ emac_ch_teardown
- emac_ch_teardown
- emac_close
+ emac_open
- emac_open
Using DaVinci-EMAC device
reason is 062fe7d332 new define MAX_PHY.
This is set to 3! I get on this board 5 active phys, so
this leads in wrong memory writes ...
so I changed:
- define CONFIG_SYS_DAVINCI_EMAC_PHY_COUNT to set
the MAX_PHY value, add a description in README
for the new CONFIG_SYS option.
- print an error message if more then MAX_PHYs are
detected.
- fill the active_phy_addr array in a for loop with
0xff
- changed printf() in debug_emac()
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Manjunath Hadli <manjunath.hadli@ti.com>
Cc: Prabhakar Lad <prabhakar.csengg@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Tom Rini <tom.rini@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fixing them here so that when the files are reused in
subsequent patches for omap5, avoids new checkpatch
warnings.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
onenand_base.c: In function ‘onenand_do_lock_cmd’:
onenand_base.c:1946:6: warning: variable ‘wp_status_mask’ set but not used
[-Wunused-but-set-variable]
onenand_base.c: In function ‘onenand_check_maf’:
onenand_base.c:2229:8: warning: variable ‘name’ set but not used
[-Wunused-but-set-variable]
onenand_base.c: In function ‘flexonenand_get_boundary’:
onenand_base.c:2258:6: warning: variable ‘ret’ set but not used
[-Wunused-but-set-variable]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
This introduces small OneNAND loader, fitting into 1kB of space (smallest
possible OneNAND RAM size). Some devices equipped with such crappy chips will
use this.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
V2: Introduce spl_onenand_load_image() to load data from OneNAND in SPL
V3: Cleanup, align with nand_spl. Skip whole blocks.
* Cleanup register definitions by introducing new regs-uart.h, compliant with
rest of U-Boot.
* Remove old register definitions from pxa-regs.h
* Convert serial_pxa to new regs-uart.h
* Cleanup serial_pxa
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This is a well encapsulated section of mmc_send_cmd, by moving
it to it's own function it increases the readability of mmc_send_cmd.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Currently when no expected completion condition occures in the
mmc_send_cmd while loop that is waiting for a data transfer to
complete the MMC driver just hangs.
This patch adds an arbitrary 2 second timeout. If nothing we
recognize occures within 2 seconds some diagnostic information
is printed and we fail out.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Currently if a DMA buffer straddles a buffer alignment boundary
(512KiB) then the DMA engine will pause and generate a DMA
interrupt. Since the DMA interrupt is not enabled it will hang
the MMC driver.
This patch adds support for restarting the DMA transfer. The
SYSTEM_ADDRESS register contains the next address that would have
been read/written when a boundary is hit. So we can read that
and write it back. The write triggers the resumption of the
transfer.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This moves the magic numbers sprinkled about the MMC driver
to a single location in the header file and gives them
meaningful names.
Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
uec.c: In function 'uec_stop':
uec.c:267:22: warning: variable 'uccf' set but not used [-Wunused-but-set-variable]
uec.c: In function 'uec_set_mac_if_mode':
uec.c:328:15: warning: variable 'uec_info' set but not used [-Wunused-but-set-variable]
uec.c: In function 'adjust_link':
uec.c:519:11: warning: variable 'uec_regs' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43:7: warning: variable 'usb_phy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
fm.c: In function 'fm_init_common':
fm.c:398:6: warning: variable 'n' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This driver supports both EHCI ports on the i.MX28 CPU.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Acked-by: Andy Fleming <afleming@gmail.com>
Fix:
mx3fb.c: In function 'video_hw_init':
mx3fb.c:827:30: warning: variable 'vesa_idx' set but not used
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
When the resolution is set to 800x600 and 1024x768,
but, the driver will use 1280x1024 resolution to set the DIU register
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
fsl_i2c.c: In function 'i2c_init':
fsl_i2c.c:245:7: warning: assignment discards qualifiers from pointer target type
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new IO FPGA implementation for Versatile Express contains an MMCI
(PL180) cell with the FIFO extended to 128 words. This causes the
read_bytes() function to go into an infinite loop; as it will wait for
for the half-full signal (SDI_STA_RXFIFOBR) if there are more than 8
words remaining (SDI_FIFO_BURST_SIZE), but it won't receive this signal
once there are fewer than 64 words left to transfer.
One possible fix is to add some build time configuration to change
SDI_FIFO_BURST_SIZE for the new implementation. However, the problematic
code only seems to exist as a small performance optimisation, so the
solution implemented by this patch is to simply remove it. The error
checking following the loop is also removed as this will be handled by
code further down the function.
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Jon Medhurst <jon.medhurst@linaro.org>
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.
Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-arm:
Arm: re-introduce the MACH_TYPE_XXXXXX for EB_CPUX9K2 board
arm: jadecpu: Readd MACH_TYPE_JADECPU
at91: defined mach-types for otc570 board in board config file
at91: defined mach-types for meesc board in board config file
mx31pdk: Enable D and I caches
ehci-mxc: remove incorrect comment
README: Fix supported i.MX SoC list for CONFIG_MXC_SPI
mx53: Turn off child clocks before reconfigure perclk_root
qong: enable support for compressed images
imx: imx31_phycore.h: fix checkpatch warnings
vision2: Remove unused get_board_rev function
mx53smd: Remove unused get_board_rev function
mx53ard: Remove unused get_board_rev function
mx53evk: Remove unused get_board_rev function
mx53evk: Add RTC support
mx53loco: Remove unused get_board_rev function
mx53evk: Remove unneeded '1' from mx53evk.h
OMAP3: mvblx: Initial support for mvBlueLYNX-X
ARM: dig297: Define MACH_TYPE_OMAP3_CPS and CONFIG_MACH_TYPE
omap3: mem: Move comments next to definitions
omap3: mem: Clean-up whitespaces
omap3: mem: Define and use common macros
Davinci: ea20: added PREBOOT to configuration
Davinci: ea20: added I2C support
Davinci: ea20: added video support
VIDEO: davinci: add framebuffer to da8xx
ARM: Davinci: added missing registers to hardware.h
Davinci: ea20: add gpios for LCD backlight control
Davinci: ea20: add gpio for keeping power on in board_late_init
Davinci: ea20: Add default U-Boot environment
Davinci: ea20: Add early init to get early output from console
Davinci: ea20: Add NAND support
Davinci: ea20: set GPIOs to hold MII-Phy in reset and set UART0-Switch for console
Davinci: ea20: set console on UART0
arm, davinci: add cam_enc_4xx support
arm926ejs, davinci: add missing spi defines for dm365
arm926ejs, davinci: add cpuinfo for dm365
arm, davinci: add lowlevel function for dm365 soc
arm, davinci: add header files for dm365
spl, nand: add 4bit HW ecc oob first nand_read_page function
arm, davinci: add support for new spl framework
spl: add option for adding post memory test to the SPL framework
net, davinci_emac: make clock divider in MDIO control register configurable
arm, usb, davinci: make USBPHY_CTL register configurable
usb, davinci: add enable_vbus() weak function
omap3evm: fix errors caused by multiple definitions
omap3evm: Add (quick) configuration for NAND only
omap3evm: Add (quick) configuration for MMC/SD only
omap3evm: move common config options to new file
omap3evm: Prepare to split configuration
omap3evm: Reorder related config options
omap/spl: actually enable the console
davinci_emac: compilation fix, phy is array now
omap3evm: Set environment variable 'ethaddr'
arm, arm926: fix missing symbols in NAND_SPL mode
arm, davinci: Add function lpsc_syncreset()
arm, davinci: replace CONFIG_PRELOADER with CONFIG_SPL_BUILD
arm/km: portl2 environment address update to P1B
arm/km: adapt bootcounter evaluation
arm/km: enable jffs2 cmds
arm/km: trigger reconfiguration for the Xilinx FPGA
arm/km: add boardid and hwkey to kernel command line
ARM: Reintroduce MACH_TYPE_KM_KIRKWOOD for keymile ARM boards
netspace_v2: enable I2C EEPROM support
netspace_v2: fix SDRAM configuration
armada100: define CONFIG_SYS_CACHELINE_SIZE
pantheon: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: define CONFIG_SYS_CACHELINE_SIZE
kirkwood: drop empty asm-offsets.s file
arm/km/mgcoge3un: enhance "waitforne" feature
arm/km: add variable waitforne to mgcoge3un
gplugD: Fix for error:MACH_TYPE_SHEEVAD undeclared
ARM: dreamplug: fix compilation
ARM: DockStar: fix compilation
ARM: netspace_v2: fix warnings
am335x: Drop board_sysinfo struct
am335x: Temporarily add MACH_TYPE define
misc:pmic:samsung Enable PMIC driver at C210 Universal target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p UNIVERSAL C210 target
dcache:s5p CONFIG_SYS_CACHELINE_SIZE added for s5p GONI target
smdkv310: use macro for mmc data read function address
smdkv310: use spl framework for mmc spl
SMDKV310: use get_ram_size() to validate dram size
SMDKV310: Initialize board id using CONFIG_MACH_TYPE
ORIGEN : use absolute paths and fix tool naming
ORIGEN : enable device tree support
MX25: tx25: Fix building due to missing MACH_TYPE
mx31: Add board support for HALE TT-01
mx31: add ESD control registers
mx31: define pins and init for UART2 and CSPI3
MX35: add support for flea3 board
MX51: vision2: add MACH_TYPE in config file
vision2: Remove unused header file
mx51evk: Remove unused get_board_rev function
mx51evk: Remove unneeded '1' from mx51evk.h
I2C: Fix mxc_i2c.c problem on imx31_phycore
mx35pdk: Add RTC support
mx51evk: Use GPIO API for configuring the IOMUX
mx51evk: Add RTC support
rtc: Make mc13783-rtc driver generic
qong: remove unneeded IOMUX settings
qong: Use mx31_set_gpr to setup USBH2 pins
mx31: Introduce mx31_set_gpr function
mx31pdk: Add MC13783 PMIC support
qong: remove unneeded "1" from qong.h
misc: pmic: fix regression in pmic_fsl.c (SPI)
mx5 configs: CONFIG_PRIME should really be CONFIG_ETHPRIME
MX35: Drop unnecessary prototypes from imx-regs.h
I2C: added I2C-2 and I2C-3 to MX35
MX35: factorize common assembly code
MX35: add reset cause as provided by other i.MX
MX35: add pins definition for UART3
MX35: added ESDC structure to imx-regs
Fix:
rtl8139.c: In function 'rtl8139_probe':
rtl8139.c:256:15: warning: variable 'fullduplex' set but not used
[-Wunused-but-set-variable]
rtl8139.c:256:6: warning: variable 'speed10' set but not used
[-Wunused-but-set-variable]
rtl8139.c: In function 'rtl_transmit':
rtl8139.c:419:16: warning: variable 'txstatus' set but not used
[-Wunused-but-set-variable]
Change code to use new debug macros; also fix the new errors and
warnigns popping up now, like "error: 'to' undeclared" and some
"warning: format '%X' expects argument of type 'unsigned int', but
argument X has type 'long unsigned int'"
Signed-off-by: Wolfgang Denk <wd@denx.de>
