On boards which have the environment in eeprom, i2c_init() is called
before the console and RAM are initialized.
Suppress printfs until the console is initialized.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
When initializing the core clocks, stick external memory into self-refresh.
This gains us a few cool things:
- support suspend-to-RAM with Linux
- reprogram clocks automatically when doing "go" on u-boot.bin in RAM
- make sure settings are stable before flashing new version
- finally fully unify initialize startup code path between LDR/non-LDR
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some newer Blackfins (like the BF51x) do not have an on-chip voltage
regulator, so do not attempt to program the memory as if it does.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the board config does not specify an explicit EBIU_SDBCTL value, set it
up with sane values based on other configuration options.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Workaround anomaly 432:
The bfrom_SysControl() firmware function does not clear the SIC_IWR1
register before executing the PLL programming sequence. Therefore, any
interrupt enabled in the SIC_IWR1 register prior to the call to
bfrom_SysControl() can prematurely terminate the idle sequence required
for the PLL to relock properly. SIC_IWR0 is properly handled.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Boot ROM uses EVT1 as the entry point so set that rather than having
to use a tiny jump block in the default EVT1 location.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The jtag tstc operation was checking the hardware to see if data is
available from it (which is fine for the jtag getc operation), but the
higher layers need to know whether any data is available. Since we have
to read up to 4 bytes at a time from the hardware, the higher layers need
to know they can consume the cached bytes as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Remove this code. It's not needed. The 4xx EMAC driver stores the MAC
addresses into the SoC registers instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Moved sub-features of the SC520 code which is currently selectively compiled
using #ifdef out of sc520.c into individual files selectively compiled via
the makefile
Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
Rewrite interrupt handling functionality for the i386 port. Separated
functionality into separate CPU and Architecture components.
It appears as if the i386 interrupt handler functionality was intended
to allow multiple handlers to be installed for a given interrupt.
Unfortunately, this functionality was not fully implemented and also
had the problem that irq_free_handler() does not allow the passing
of the handler function pointer and therefore could never be used to
free specific handlers that had been installed for a given IRQ.
There were also various issues with array bounds not being fully
tested.
I had two objectives in mind for the new implementation:
1) Keep the implementation as similar as possible to existing
implementations. To that end, I have used the leon2/3
implementations as the reference
2) Seperate CPU and Architecture specific elements. All specific i386
interrupt functionality is now in cpu/i386/ with the high level
API and architecture specific code in lib_i386. Functionality
specific to the PC/AT architecture (i.e. cascaded i8259 PICs) has
been further split out into an individual file to allow for the
implementation of the PIC architecture of the SC520 CPU (supports
more IRQs)
Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script. Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.
However, '*(.rodata*)' by itself will result in sub-optimal section
ordering. The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file. This is easy to fix by using the
SORT_BY_ALIGNMENT command.
This patch has not be tested one most of the boards modified. Some boards
have a linker script that looks something like this:
*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)
I change this to:
*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The resulting code can also be simplified even further.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Stefan Roese <sr@denx.de>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
The cpus that get converted here:
at91rm9200
mpc512x
mpc5xxx
mpc8260
mpc8xx
ppc4xx
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: John Rigby <jrigby@freescale.com>
CC: Stefan Roese <sr@denx.de>
PCI outbound address map configuration doesn't match the
PCI memory address range covered by appropriate TLB entry
configuration for canyonlands causing machine check
exceptions while accessing PCI memory regions. This patch
provides a fix for this issue.
Kazuaki Ichinohe observed and reported this issue while
testing display output with PCI ATI video card on canyonlands.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Total5200 and digsy MTC use I2C port 2 pins as a ATA chip select.
To avoid adding board-specific ifdefs to cpu/mpc5xxx/ide.c new
define CONFIG_SYS_ATA_CS_ON_I2C2 was introduced. It is used by
Total5200 and will be used by digsy MTC and other boards with
ATA CS on I2C pins.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
The serial boot dram extended/standard mode register was not
setup and was using default DRAM setup causing the U-boot was
unstable to boot up in serial mode.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
According to coldfire manual data timeout > address time out
also use correct macro to program XARB_CFG
Signed-off-by: Arun C <arunedarath@mistralsolutions.com>
The routine assumed 4 bank SDRAMs, enhance to configure for 4 or 8
bank SDRAMs.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch makes sure the correct mask is applied when setting
the encryption and I2C bus 0 clock in SCCR.
Failing to do so may lead to ENCCM being 0 in which case I2C bus 0
won't function.
Signed-off-by: Norbert van Bolhuis <nvbolhuis@aimvalley.nl>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit e1be0d25, "32bit BUg fix for DDR2 on 8572" prevented other
sdram_cfg bits (such as ecc and self_refresh_in_sleep) from being set.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
add CONFIG_BOOTCOUNT_LIMIT feature for 8360 CPU.
The bootcounter uses 8 bytes from the muram,
because no other memory was found on this
CPU for the bootcount feature. So we must
correct the muram size in DTS before booting
Linux.
This feature is actual only implemented for
MPC8360, because not all 83xx CPU have qe,
and therefore no muram, which this feature
uses.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
1. RD_TO_PRE missed to add the AL, and need min 2 clocks for
tRTP according to DDR2 JEDEC spec.
2. WRTORD - tWTR need min 2 clocks according to DDR2 JEDEC spec.
3. add the support of DDR2-533,667,800 DIMMs
4. cpo
5. make the AL to min to gain better performance.
The Micron MT9HTF6472CHY-667D1 DIMMs test passed on
MPC837xEMDS platform at 266MHz/333MHz/400MHz data rate.
items 1, 2 and 5:
Acked-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reported-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We should use pci_last_busno() in pci_init_bus(), otherwise we'll
erroneously re-use PCI0's first_busno for PCI1 hoses.
NOTE: The patch is untested. All MPC83xx FSL boards I have have
PCI1 in miniPCI form, for which I don't have any cards handy.
But looking in cpu/mpc85xx/pci.c:
...
#ifdef CONFIG_MPC85XX_PCI2
hose = &pci_hose[1];
hose->first_busno = pci_hose[0].last_busno + 1;
And considering that we do the same for MPC83xx PCI-E support,
I think this patch is correct.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes copy-paste issue: pci_hose[0]'s first and last
busnos were used to fixup pci1's nodes.
We don't see this bug triggering only because Linux reenumerate
buses anyway.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes an issue in config space read accessors: we should
fill-in the value even if we fail (e.g. skipping devices), otherwise
CONFIG_PCI_SCAN_SHOW reports bogus values during boot up.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
