Instead of redefining a pin's name size, use PINNAME_SIZE defined
in include/dm/pinctrl.h
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pin-controller pin's name must be equal to pin's name used in device
tree with "pins" DT property.
Issue detected on stm32mp157c-ev1 board with goodix touchscreen.
In DT, the goodix's pin is declared in DT with the node:
goodix_pins: goodix {
pins = "gpio14";
bias-pull-down;
};
Whereas in stmfx pin-controller driver, pin's name are equal to
"stmfx_gpioxx" where xx is the pin number.
This lead to not configure stmfx's pins at probe because pins is
identified by its name (see pinctrl_pin_name_to_selector() in
pinctrl-generic.c) and stmfx pin "gpio14" can't be found.
To fix this issue, come back to the original stmfx pin's name.
Revert "pinctrl: stmfx: update pin name"
This reverts commit 38d30cdcd65c73eeefac5efa328ad444a53b77dd.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable the fastboot oem command bootbus, used to configure the eMMC
boot behavior, with same format than 'mmc bootbus'
and with parameter: boot_bus_width reset_boot_bus_width boot_mode
On stm32mp1 boards the expected command is
$> fastboot oem partconf:0 0 0
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable the fastboot oem command partconf, used to select the correct
eMMC boot partition, with same format than 'mmc partconf'
with parameter: boot_ack boot_partition
On stm32mp1 family:
- boot_ack = 1 (Boot Acknowledge is needed by ROM code)
- boot_partition = 1 or 2 (Boot partition 1 / 2 enabled for boot)
So on EV1 board the expected commands to select boot partition 1 or 2
$> fastboot oem partconf:1 1
$> fastboot oem partconf:1 2
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable the fastboot oem command format and set the variable
"partitions" with default eMMC partitions list.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Jean-Philippe ROMAIN <jean-philippe.romain@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Update gpio driver to use same logic for big-endian and little-endian
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Drop the CONFIG_VIDEO to fix the following build warning.
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
UPD include/generated/dt.h
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
UPD include/generated/timestamp_autogenerated.h
====================================================
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Update data type of '1' to '1ull' in below assignment
size = 1ull << sizebit;
to fix incorrect assignment issue.
e.g: when sizebit was 31, 0x80000000 got sign extended to
0xffffffff_80000000
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reported-by: Dean Saridakis <dean.saridakis@baesystems.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Enable the I-Cache to speed up the boot time, especailly for the NOR
boot, currently it takes about 15 seconds from power up to the U-Boot
prompt, and with the I-Cache enabled it only takes around 2.5 seconds.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.
With the previous settings SPI-NAND reads over AHB were
corrupted.
Fixes: 91afd36f38 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
