This patch includes the following changes for the lwmon5 board support:
- Enable cache in SDRAM
- Use common EHCI driver instead of the PPC4xx specific OHCI driver
This can be done since only high-speed devices are connected.
- Remove cached TLB entry again after ECC setup
- Use correct define for cache enabling
(CONFIG_4xx_DCACHE instead of CONFIG_SYS_ENABLE_SDRAM_CACHE)
- Enable FIT image support
Signed-off-by: Stefan Roese <sr@denx.de>
The t3corp board has an Xilinx DS617 flash chip connected to the
onboard FPGA. This patch adds support for these chips. Board
specific flash accessor functions are needed, since the chips
can only be read correctly in 16bit mode.
Additionally the FPGA chip-selects are configured for device-paced
transfers (ready is enabled).
Signed-off-by: Stefan Roese <sr@denx.de>
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with
* Processor upto 1.2GHz
* Parallel 1Gb x8 DDR2-1066 MHz
* 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR
* Footprints for eMMC/eSD NAND & MMC x8 card
* 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket
* SEAF memory board, subset of PISMO2
With Peripherals:
* 4.3” WVGA 24-bit LCD
* Audio codecs (AC97 & I2S), TSI
* VGA camera
* Video in via 3 RCA jacks, and HDMI type C out
* Marvell 88W8688 802.11bg/BT module
* GPS RF IC
* Dual analog mics & speakers, headset jack, LED, ambient light sensor
* USB2.0 HS host (A), OTG (micro AB)
* FE PHY, PCIE Mini Card slot
* GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR
This patch adds basic board support with DRAM and UART functionality
The patch is tested for boot from DRAM using XDB
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
- serial console in PSC1
- 128MiB DRAM
- 32MiB Flash
- FEC Ethernet
- 2 I2C busses
- FPGA on CS3
- IDE
- VGA SMI501
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixes the acadia_nand and kilauea_nand linker scripts
which have been missing in commit ee8028b7 [ppc4xx: Cleanup for
partial linking and --gc-sections]
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bernhard Weirich <Bernhard.Weirich@riedel.net>
On the P1022, the pins which drive the video display (DIU) are muxed with the
local bus controller (LBC), so if the DIU is active, the pins need to be
temporarily muxed to LBC whenever accessing NOR flash.
The code which handled this transition is checking and changing the wrong
bits in PMUXCR.
Also add a follow-up read after a write to NOR flash if we're going to
mux back to DIU after the write, as described in the P1022 RM.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add battery charging support twl6030 driver.
Add support for battery voltage and current measurements.
Add command to get battery status and start/stop battery charging from USB.
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Recent cleanup actions resulted in a number of config.mk files that
contained only LDSCRIPT definitions. Move these into th respective
board config files and remove the now empty config.mk files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andre Schwarz <andre.schwarz@matrix-vision.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Detlev Zundel < dzu@denx.de>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher<hs@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Recent cleanup actions resulted in a number of config.mk files that
contained only redundant entries like
PLATFORM_CPPFLAGS += -I$(TOPDIR)
or settings of variables that were not used anywhere in the code, like
TEXT_END = 0xfe080000
Remove these unnecessary files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Scott McNutt <smcnutt@psyent.com>
Cc: Wolfgang Wegner <w.wegner@astro-kom.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Tolunay Orkun <torkun@nextio.com>
Cc: Frank Panno <fpanno@delphintech.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Brad Kemp <Brad.Kemp@seranoa.com>
Acked-by: Heiko Schocher<hs@denx.de>
This board uses the OMAP-L138 SOM stacked on a
custom baseboard. It supports SPI Flash, Ethernet
with RMII.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
As more Davinci 8xx board can be added, move common code
to be shared between boards.
* rebased ontop of Sugosh's patches
* moving the HAWKBOARD_KICK{0,1}_UNLOCK defines to
arch/arm/include/asm/arch-davinci/davinci_misc.h from to
arch/arm/include/asm/arch-davinci/da8xx_common.h
* don't define dram functions in PRELOADER
* move sync_env_enetaddr into existing EMAC ifdef
* use misc.c in hawkboard nand_spl
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.
The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.
Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove the board_init_f function from nand_spl/nand_boot.c. This
function is to be defined by all boards using the nand_spl
functionality in their individual board directory.
Currently this function was being used by the smdk6400 board. Added
the board specific function definition.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
board/davinci.
Move the davinci common headers to the architecture specific
include file path.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fix ca9x4_ct_vxp build error
Configuring for ca9x4_ct_vxp board...
board/armltd/vexpress/libvexpress.o: In function `udelay':
u-boot.git/board/armltd/vexpress/ca9x4_ct_vxp.c:161: multiple
definition of `udelay'
lib/libgeneric.o:u-boot.git/lib/time.c:34: first defined here
lib/libgeneric.o: In function `udelay':
zlib.c:(.text+0x1ee8): undefined reference to `__udelay'
Signed-of-by: Dirk Behme <dirk.behme@googlemail.com>
This patch fixes build errors in the vexpress system:
- Removed sys_proto.h requirement from syslib.c.
- Switched vexpress to the default armv7 linker script.
- Renamed TEXT_BASE to CONFIG_SYS_TEXT_BASE.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
This patch also removes now unnecessary config.mk in board directory and
make usage of new features in boards.cfg.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Adds support for the EMK TOP9000 CPU Module which is
based on ATMELs ARM926EJS AT91SAM9XE SoC.
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
Since the driver is used not only on Freescale boards,
we move it to a common place for video drivers as
suggested by Wolfgang. The patch also cleans up the
top level Makefile.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Since board_hwconfig & cpu_hwconfig are defined as weak and dont have a
default value they will get put into the BSS if they aren't defined
elsewhere. This is problematic as we try to utilize hwconfig before
we've relocated and thus BSS isn't setup.
Instead of giving dummy values in the board files that utilize this
feature, we can just initialize the variables to an empty string and
thus move them out of the BSS if they aren't defined elsewhere.
Also made board_hwconfig & cpu_hwconfig arrays to reduce size associated
with string pointers vs arrays.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Also change the CONFIG_SYS_TEXT_BASE to 0x80008000, required
with relocation support. This is the load address for primary
boot loader (x-loader).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The duplication of the do_bootm prototype has gotten out of hand,
and they're pretty much all outdated (wrt constness). Unify them
all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the return value of cmd_usage instead of ignoring this
and returning a 1.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* Fix memory initialization. This fixes the problem
with kernel oopses during heavy load.
* Cleanup pinsetup, which for reference is among
other things needed for proper flash erasing.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
This commit adapts 4xx boards for partial linking with --gc-sections.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: David Updegraff <dave@cray.com>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Larry Johnson <lrj@acm.org>
Cc: Peter De Schrijver <p2@mind.be>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Cc: Daniel Poirot <dan.poirot@windriver.com>
Acked-by: Stefan Roese <sr@denx.de>
This change is needed to compile the PPC4xx NAND booting targets
equipped with the IBM DDR2 SDRAM controller.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
These boards use an embedded environment, which is not supported by the
generic arch/powerpc/cpu/ppc4xx/u-boot.lds script.
The breakage was introduced by commit 2cd95a2 "ppc4xx: Remove board
specific linker scripts from most PPC4xx boards"
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Andrea Marson <andrea.marson@dave-tech.it>
Acked-by: Stefan Roese <sr@denx.de>
Fix warnings:
cam5200_flash.c: In function 'write_word_32':
cam5200_flash.c:443: warning: dereferencing type-punned pointer will break strict-aliasing rules
cam5200_flash.c: In function 'write_word_16':
cam5200_flash.c:684: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
