imx_ddr_size() can be used to calculate the DDR size in runtime.
By using this function we no longer need to define PHYS_SDRAM_SIZE.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently it's recommended to move some configuration options to the
defconfig file.
Move some USB related options to the defconfig file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
This commit adds support for the Toradex Computer on Modules
Colibri iMX7S/iMX7D. The two modules/SoC's are very similar hence
can be easily supported by one board. The board code detects RAM
size at runtime which is one of the differences between the two
boards. The board also uses the UART's in DTE mode, hence making
use of the new DTE support via serial DM.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The hwconfig env var allows user to control hardware specific configuration
of board specific features but not all Ventana boards have the same features.
We will use the magic default value of "_UNKNOWN_" to signify that the
bootloader should create this based on detected board model.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
3b1f681131 caused a regression that removes
board info dispaly for Gateworks Ventana boards because it made the invalid
assumption that CONFIG_DISPLAY_BOARDINFO_LATE was the same thing as
CONFIG_DISPLAY_BOARDINFO.
Ventana needs to call show_board_info in late init because we need to have
the i2c eeprom based model info. Re-define CONFIG_DISPLAY_BOARDINFO_LATE
to allow that to happen.
Cc: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The IMX6 PCIe host controller does not have a proper reset and as such there
are several issues that can arise if PCI is enabled in the bootloader follwed
by Linux trying to re-configure LTSSM and/or toggling PERST# to the devices.
For now, the best approach seems to default to disabling PCI by defaulting
pciedisable=1. This can be overridden by the user if they need PCI in the
bootloader, for example:
- GW552x needing ethernet access in bootloader
- GW16082 expansion board needing a device-tree fixup for irq mapping
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
USB gadget configuration is set in defconfig and
must be removed from pico-imx6ul.h.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Use existing Kconfig symbols to let the user configure whether to
build a U-Boot with non-secure mode support or not. This also allows
to enable virtualization extension easily.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
CONFIG_DISPLAY_BOARDINFO should not be placed in mx7_common
because some boards might need a different config such as
CONFIG_DISPLAY_BOARDINFO_LATE. Move it to the board file
instead.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This can be useful if the same U-Boot binary is used for boards
available with a i.MX 7Solo and i.MX 7Dual.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The cm-fx6 module has an on-board spi flash chip. Enable mtd support
and the mtdparts command. Also define a default partitioning, add
it to the default environment, and enable support to overwrite the
partitioning defined in a device tree by it. Finally, probe for the
chip on preboot to register the flash chip and, thus, establish the
connection between the mtd environment settings and the actual device.
These changes move the effective default partitioning from the device
tree shipped with the vendor kernels to U-Boot which becomes the single
point of definition for the partitioning for all device tree based
kernels (in particular, for the upstream Linux kernel which does not
have a default partitioning defined in its device tree).
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Currently, entire script segments have to be changed in the default
environment to change the kernel image location or to append kernel
cmdline parameters. In the later case this has to be changed for
every possible boot device.
Introduce new variables for kernel image locations and boot device
independent kernel parameters to make it easier to change these
settings.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Nikita Kiryanov <nikita@compulab.co.il>
Recently I started to notice that u-boot.img built for Wandboard
by some toolchains becomes so large that it basically overlaps with
U-Boot environment area on SD-card.
According to
http://wiki.wandboard.org/index.php/Boot-process#sdcard_boot_data_layout
Wandboard's SD-card layout is as follows:
------------------------------>8---------------------------
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
==========================================================
1. 0x00000000 Reserved For MBR
2. 0x00000200 512 Secondary Image Table (optional)
3. 0x00000400 1024 uBoot Image (Starting From IVT)
4. 0x00060000 393216 start of uboot env (size:8k)
5. 0x00062000 end of uboot env
6. 0x00100000 1048576 Linux kernel start
7. 0x0076AC00 7777280 start of partition 1
------------------------------>8---------------------------
So for U-Boot we have 383kB (392192 bytes).
But in up to date U-Boot for Wandboard we build separately
a) SPL
b) u-boot.img
which gives us a bit more detailed SD-card layout:
------------------------------>8---------------------------
==========================================================
1. 0x00000000 Reserved For MBR
2. 0x00000200 512 Secondary Image Table (optional)
3. 0x00000400 1024 SPL
4. 0x00011400 70656 u-boot.img
5. 0x00060000 393216 start of uboot env (size:8k)
6. 0x00062000 end of uboot env
...
------------------------------>8---------------------------
>From that layout we may calculate amount of space reserved for
u-boot.img. It's just 315kb (322560 bytes).
Now if I build U-Boot with Sourcery CodeBench ARM 2014.05 produced
u-boot.img is already more than we expected
(323840 bytes instead of "< 322560"):
------------------------------>8---------------------------
ls -la u-boot.img
-rw-rw-r-- 1 user user 323840 Jul 5 07:38 u-boot.img
------------------------------>8---------------------------
Funny enough if I rebuild U-Boot with ARM toolchain available in
my Fedora 23 distro u-boot.img becomes a little bit smaller:
------------------------------>8---------------------------
ls -la u-boot.img
-rw-rw-r-- 1 user user 322216 Jul 5 07:39 u-boot.img
------------------------------>8---------------------------
What's worse this problem might not affect people most of the time
because what happens people would just copy u-boot.img on SD-card and
live in happiness with it... well until somebody attempts to save
environment in U-Boot with "saveenv" command which will simply
overwrite the very end of u-boot.img.
That will lead to unusable SD-card until user dd u-boot.img on
SD-card again.
I may foresee this issue in the future to become more visible once we
add more features in U-Boot for Wandboard or just existing code base
becomes bulkier and people will consistently get larger u-boot.img
files produced.
IMHO there's an obvious solution for all that - just move U-Boot's env
to the very end of the gap between U-Boot and the first real partition
on the SD-card. This patch will follow
8fb9eea565 ("mx6sabre_common: Fix U-Boot corruption after 'saveenv'").
So env is still not in the very end of the gap (obviously 256kb is way
too much for U-Boot's env) but at least we have now the same
partitioning for i.MX6 boards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Wolfgang Denk <wd@denx.de>
Define a default board_run_command() function. This function contains
the commands needed to boot the board when CLI is disabled (CONFIG_CMDLINE=n).
Signed-off-by: Andrej Rosano <andrej@inversepath.com>
Add USB host support.
Tested by connecting a USB pen drive:
=> usb start
starting USB...
USB0: Port not available.
USB1: USB EHCI 1.00
scanning bus 1 for devices... 2 USB Device(s) found
scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add script for retrieving the kernel via TFTP and mounting the
rootfs via NFS.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
DFU is a convenient way to program U-boot binary into the eMMC.
Add support for it.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Pico-imx6ul has a KSZ8081 Ethernet PHY.
Add support for it.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of passing the total RAM size via PHYS_SDRAM_SIZE option,
we should better use imx_ddr_size() function, which automatically
determines the RAM size.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
Custom Board based on MX6 Dual, 1GB RAM and eMMC.
There are two variants of the board with and without
PCIe (ZC5202 and ZC5601).
Signed-off-by: Stefano Babic <sbabic@denx.de>
Commit 9262367 moves USB errata workaround into a C file. This
causes compiling error for kmcoge4 and kmlion1. To enable the
errata workaround, define CONFIG_USB_EHCI_FSL in common header.
Signed-off-by: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ed Swarthout <Ed.Swarthout@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Fixes: 92623672f9 ("fsl: usb: make errata function common for PPC and ARM")
As the help message of CONFIG_BOOTDELAY says, CONFIG_BOOTDELAY=-2
means the autoboot with no delay, with no abort check even if
CONFIG_ZERO_BOOTDELAY_CHECK is defined.
To sum up, the autoboot behaves as follows:
[1] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=y
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
autoboot with no delay, with no check for abort
[3] CONFIG_BOOTDELAY=-1
disable autoboot
[4] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
As you notice, [2] and [4] come to the same result, which means we
do not need CONFIG_ZERO_BOOTDELAY_CHECK. We can control all the
cases only by CONFIG_BOOTDELAY, like this:
[1] CONFIG_BOOTDELAY=0
autoboot with no delay, but you can abort it by key input
[2] CONFIG_BOOTDELAY=-1
disable autoboot
[3] CONFIG_BOOTDELAY=-2
autoboot with no delay, with no check for abort
This commit converts the logic as follow:
CONFIG_BOOTDELAY=0 && CONFIG_ZERO_BOOTDELAY_CHECK=n
--> CONFIG_BOOTDELAY=-2
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Christian Riesch <christian.riesch@omicronenergy.com>
Acked-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Now I2C is initialized early enough to access FPGA so it supports to
show board info as early as other boot methods.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
I still see some defines of this config in board headers. Move them
to defconfigs (+ renaming to CONFIG_HUSH_PARSER) to complete this
migration.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Introduce a meson-gxbb-common.h header file and derive the
configuration for Hardkernel Odroid-C2 board from that.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>
This fixes commit d31e9c575f ,
which broke booting from SD card on all SoCFPGA boards. The
patch assumes the bootloader partition to be partition 3, at
the end of the SD card, which doesn't make any sense. U-Boot
assumes the bootloader partition is partition 1 or that the
bootloader image is at offset +1 MiB from the start of SD card.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sylvain Lesne <lesne@alse-fr.com>
Due to changes in distro environment, ENV_SIZE limit was reached on Dragonboard.
This patch increases environment size to 8KiB.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
At first, 256 byte of the head of DRAM space was reserved for some
reasons. However, as the progress of development, it turned out
unnecessary, and it was never used in the end. Move the CPU release
address to leave no space.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
