Update OneNAND command to support bad block awareness.
Also change the OneNAND command style to better match the
NAND version.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
The code in fdt_resize() to extend the fdt size to end on a page boundary
is wrong for fdt's not located at an address aligned on a page boundary.
What's even worse, the code would make actualsize shrink rather than grow
if (blob & 0xfff) was bigger than the amount of padding added by ALIGN(),
causing fdt_add_mem_rsv to fail.
Fix it by aligning end address (blob + size) to a page boundary instead.
For aligned fdt's this is equivalent to what we had before.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
If both CONFIG_ENV_SECT_SIZE and CONFIG_ENV_SIZE are defined, and the sect
size is larger than the env size, then it means the env is embedded in a
block. So we have to save/restore the part of the sector which is not the
environment. Previously, saving the environment in SPI flash in this
setup would probably brick the board as the rest of the sector tends to
contain actual U-Boot data/code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
FDT support is used for both FIT style images and for architectures
that can pass a fdt blob to an OS (ppc, m68k, sparc).
For other architectures and boards which do not pass a fdt blob to an
OS but want to use the new uImage format, we just need FIT support.
Now we can have the 4 following configurations :
1) FIT only CONFIG_FIT
2) fdt blob only CONFIG_OF_LIBFDT
3) both CONFIG_OF_LIBFDT & CONFIG_FIT
4) none none
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
With this patch we set the type back to NONE upon failing UBI partition
initialization. Otherwise further calls to the UBI subsystem would try
to really access the non-existing UBI partition.
Thanks to Michael Lawnick for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
With this patch now, the user can call "ubi part" multiple times to
re-connect the UBI device to another MTD partition.
Signed-off-by: Stefan Roese <sr@denx.de>
rename devices_init () in common/jffs2.c to
jffs2_devices_init (), because there is also a
devices_init () in common/devices.c.
Signed-off-by: Heiko Schocher <hs@denx.de>
Modifications to support console multiplexing. This is controlled using
CONFIG_SYS_CONSOLE_MUX in the board configuration file.
This allows a user to specify multiple console devices in the environment
with a command like this: setenv stdin serial,nc. As a result, the user can
enter text on both the serial and netconsole interfaces.
All devices - stdin, stdout and stderr - can be set in this manner.
1) common/iomux.c and include/iomux.h contain the environment setting
implementation.
2) doc/README.iomux contains a somewhat more detailed description.
3) The implementation in (1) is called from common/cmd_nvedit.c to
handle setenv and from common/console.c to handle initialization of
input/output devices at boot time.
4) common/console.c also contains the code needed to poll multiple console
devices for input and send output to all devices registered for output.
5) include/common.h includes iomux.h and common/Makefile generates iomux.o
when CONFIG_SYS_CONSOLE_MUX is set.
Signed-off-by: Gary Jennejohn <garyj@denx.de>
When running `strings` on really long strings, the stack tends to get
smashed due to printf(). Switch to puts() instead since we're only passing
the data through.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
- fix size too small by one in sprintf
- changed old (pre 2004) device name ibmEmac to emac
- boot device may be overriden in board config
- servername may be defined in board config
- additional parameters may be defined in board config
- fixed some line wrappings
- replaced redundant MAX define by max
Signed-off-by: Niklaus Giger <niklaus.giger@member.fsf.org>
When CONFIG_SYS_HUSH_PARSER is defined network download
commands with 1 argument in the format 'tftp "/path/file"'
do not work as expected. The hush command parser strips
the quotes from "/path/file" which causes the network
commands to interpret "/path/file" as an address
instead of the intended filename.
The previous check for a leading quote in netboot_common()
was replaced with a check which ensures only valid
numbers are treated as addresses.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Without this patch "saveenv" crashes when MTD partitions are enabled (e.g.
for use in UBI) via CONFIG_MTD_PARTITIONS.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Currently the size parameters of the UBI commands (e.g. "ubi write") are
decoded as decimal instead of hex as default. This patch now interprets
all these values consistantly as hex, as all other standard U-Boot commands
do.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds these UBI commands:
ubi part [nand|onenand] [part] - Show or set current partition
ubi info [l[ayout]] -Display volume and UBI layout information
ubi create[vol] volume [size] [type] - Create volume name with size
ubi write[vol] address volume size - Write volume from address with size
ubi read[vol] address volume [size] - Read volume to address with size
ubi remove[vol] volume - Remove volume
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Stefan Roese <sr@denx.de>
fdt_add_mem_rsv() requires space for a struct fdt_reserve_entry
(16 bytes), so make sure that fdt_resize at least adds that much
padding, no matter what the location or size of the fdt is.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Andy Fleming <afleming@freescale.com>
Add the ability to break the steps of the bootm command into several
subcommands: start, loados, ramdisk, fdt, bdt, cmdline, prep, go.
This allows us to do things like manipulate device trees before
they are passed to a booting kernel or setup memory for a secondary
core in multicore situations.
Not all OS types support all subcommands (currently only start, loados,
ramdisk, fdt, and go are supported).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This removes a bit of code and makes it easier for the upcoming sub bootm
command support to call into the proper OS specific handler.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
The information displayed when CONFIG_LCD_INFO is set is inherently
board-specific, so it should be done by the board code. The current code
dealing with this only handles two cases, and is already a horrible mess
of #ifdeffery.
Yes, this duplicates some code, but it also allows boards to print more
board-specific information; this used to be very difficult.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This allows the logo/info rendering routines to use the regular
lcd_putc/lcd_puts/lcd_printf calls.
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
lcd_printf() has a prototype in include/lcd.h but no implementation. Fix
this by borrowing the lcd_printf() implementation from the cogent board
code (which appears to use its own LCD framework.)
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Added fdt_pci_dma_ranges() that parses the pci_region info from the
struct pci_controller and populates the dma-ranges based on it.
The max # of windws/dma-ranges we support is 3 since on embedded
PowerPC based systems this is the max number of windows.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Add helper functions to return find a node and return it's property
or a default value.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Each architecture has different ways of determine what regions of memory
might not be valid to get overwritten when we boot. This provides a
hook to allow them to reserve any regions they care about. Currently
only ppc, m68k and sparc need/use this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Sub-command can benefit from using the same table and search functions
that top level commands have. Expose this functionality by refactoring
find_cmd() and introducing find_cmd_tbl() that sub-command processing
can call.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This new command shows the local variables defined in
the hush shell:
=> help showvar
showvar
- print values of all hushshell variables
showvar name ...
- print value of hushshell variable 'name'
Also make the set_local_var() and unset_local_var ()
no longer static, so it is possible to define local
hush shell variables at boot time. If CONFIG_HUSH_INIT_VAR
is defined, u-boot calls hush_init_var (), where
boardspecific code can define local hush shell
variables at boottime.
Signed-off-by: Heiko Schocher <hs@denx.de>
With this Command it is possible to add new I2C Busses,
which are behind 1 .. n I2C Muxes. Details see README.
Signed-off-by: Heiko Schocher <hs@denx.de>
If I2C Bus is blocked (see doc/I2C_Edge_Conditions),
it is not possible to get out of this, until the
complete Hardware gets a reset. This new commando
calls again i2c_init (and that calls i2c_init_board
if defined), which will deblock the I2C Bus.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Now that the auto-update feature uses the 'firmware' type for updates, it is
useful to inspect the load address of such images.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
The auto-update feature allows to automatically download software updates
from a TFTP server and store them in Flash memory during boot. Updates are
contained in a FIT file and protected with SHA-1 checksum.
More detailed description can be found in doc/README.update.
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
The upcoming automatic update feature needs the ability to adjust an
address within Flash to the end of its respective sector. Factor out
this functionality to a new function flash_sect_roundb().
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added as a convenience for other platforms that uses MPC8360 (has 8 UCC).
Six eth interface is chosen because the platform I am using combines
UCC1&2 and UCC3&4 as 1000 Eth and the other four UCCs as 10/100 Eth.
Signed-off-by: Richard Retanubun <RichardRetanubun@RugggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Original code displayed:
=> help i2c
i2c i2c speed [speed] - show or set I2C bus speed
i2c md chip address[.0, .1, .2] [# of objects] - read from I2C device
...
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The max packet size is encoded as 0,1,2,3 for 8,16,32,64 bytes.
At some places directly 8,16,32,64 was used instead of the encoded
value. Made a enum for the options to make this more clear and to help
preventing similar errors in the future.
After fixing this bug it became clear that another bug existed where
the 'pipe' is and-ed with PIPE_* flags, where it should have been
'usb_pipetype(pipe)', or even better usb_pipeint(pipe).
Also removed the triple 'get_device_descriptor' sequence, it has no use,
and Windows nor Linux behaves that way.
There is also a poll going on with a timeout when usb_control_msg() fails.
However, the poll is useless, because the flag will never be set on a error,
because there is no code that runs in a parallel that can set this flag.
Changed this to something more logical.
Tested on AT91SAM9261ek and compared the flow on the USB bus to what
Linux is doing. There is no difference anymore in the early initialisation
sequence.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Since we're working with unsigned data, you can't apply a signed pointer
cast and then attempt to print the result. Otherwise you get wrong output
when the sign bit is set like "0xFF" incorrectly extended to "0xFFFFFFFF".
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
We don't need CONFIG_CFG_STRINGS anymore now that we have the define
CONFIG_CMD_STRINGS and Makefile control.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are several differences between Linux, Windows and U-boot for initialising the
USB devices. While analysing the behaviour of U-boot it turned out that U-boot does
things really different, and some are wrong (compared to the USB standard).
This patch fixes some errors:
* The NEW_init procedure that was already in the code is good, while the old procedure
is wrong. See code comments for more info.
* On a Control request the data returned by the device can be more than 8 bytes, while
the host limits it to 8 bytes. This caused the host to generate a DataOverrun error.
This results in a lot of USB sticks not being recognised, and the transmission ended
frequently with a CTL:TIMEOUT Error.
* Added a flag CONFIG_LEGACY_USB_INIT_SEQ to allow users to use the old init procedure.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
This patch refactors some large routines of the USB OHCI code by
making some routines smaller and more readable which helps
debugging and understanding the code. (Makes the code looks
somewhat more like the Linux implementation.)
Also made entire file compliant to Linux Coding Rules (checkpatch.pl compliant)
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
The GCC-compiler makes an optimisation error while optimising the routine
usb_set_maxpacket(). This should be fixed in the compiler in the first place,
but there lots of compilers out there that makes this error, that it is
probably wiser to workaround it in U-boot itself.
What happens is that the register r3 is used as loop-counter 'i', but gets
overwritten later on. From there it starts using register r3 for several other
things and the assembler code is becoming a big mess. This is clearly a compiler bug.
This error occurs on at least several versions of Code Sourcery Lite compilers
for ARM. Like the Edition 2008q1, and 2008q3, It has also been seen on other
compilers, while compiling for armv4t, or armv5te with Os, O1 and O2.
We work around it by splitting up this routine in 2 parts, and making sure that
the split out part is NOT inlined any longer. This will make GCC spit out assembler
that do not show this problem. Another possibility is to adapt the Makefile to stop
optimisation for the complete file. I think this solution is nicer.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Markus Klotzbuecher <mk@denx.de>
Commit 2a1a2cb6 didnt remove the dummy mem reservation in fdt_chosen,
and this stopped Linux from booting with a Ramdisk. This patch fixes
this, by deleting the useless dummy mem reservation.
When booting with a Ramdisk, a fix offset FDT_RAMDISK_OVERHEAD is now
added to of_size, so we dont need anymore a dummy mem reservation.
I measured the value of FDT_RAMDISK_OVERHEAD on a MPC8270 based
system (=0x44 bytes) and rounded it up to 0x80).
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
When not using hush, the autoscr command now executes lines that are
only one character long. It also runs the last line of scripts even if
it does not end in a newline.
Signed-off-by: Petri Lehtinen <petri.lehtinen@inoi.fi>
Fix printf format-string/arg mismatches under -DDEBUG.
These warnings occur with DEBUG defined for a platform using
cpu/mpc85xx. Users of other architectures can unearth similar
problems by adding the line "CFLAGS += -DDEBUG=1" in config.mk right
after "CFLAGS += $(call cc-option,-fno-stack-protector)".
Signed-off-by: Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The patch is that check if usb_get_dev_index() function return valid
pointer. If valid, continue. Otherwise return -1.
Signed-off-by: Ryan Chen <ryan.chen@st.com>
Acked-by: Markus Klotzbuecher <mk@denx.de>
A recent commit (936897d4d1)
enabled the usb_stop() command in common/cmd_bootm.c which was
not enabled for some time, because no board did actually set the
CFG_CMD_USB flag. So, now the usb_stop() is executed before
loading the linux kernel.
However, the usb_ohci driver hangs up (at least on AT91SAM) if the
driver is stopped twice (e.g. the peripheral clock is stopped on AT91).
If some other piece of code calls usb_stop() before the bootm command,
this command will hangup the system during boot.
(usb start and stop is typically used while booting from usb memory stick)
But, stopping the usb stack twice is useless anyway, and a flag already
existed that kept track on the usb_init()/usb_stop() calls.
So, we now check if the usb stack is really started before we stop it.
This problem is now fixed in both the upper as low-level layer.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Markus Klotzbuecher <mk@denx.de>