The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was
released by Amazon back in 2011.
It is using an OMAP4430 SoC GP version, which allows running U-Boot and the
U-Boot SPL from the ground up.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This is based on the davinci da850evm. It can boot from either the
on-board 16MB flash or from a microSD card. It also reads board
information from an I2C EEPROM.
The EV3 itself initally boots from write-protected EEPROM, so no
u-boot SPL is needed.
Signed-off-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable support for PMMC the TI power processor on K2G. This processor
manages all power management related activities on the SoC and and
allows the Operating Systems on compute processors such as ARM, DSP to
offload the power logic away into the power processor.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Various boards have the wrong Kconfig ordering now. To avoid a misleading
diff in the next patch, reorder the configuration correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
- FEC Ethernet
- USB Ports
- SDHC and MMC boot
- SPI NOR
- LVDS and HDMI display
Basic information about the module:
- Module manufacturer: Advantech
- CPU: Freescale ARM Cortex-A9 i.MX6D
- SPECS:
Up to 2GB Onboard DDR3 Memory;
Up to 16GB Onboard eMMC NAND Flash
Supports OpenGL ES 2.0 and OpenVG 1.1
HDMI, 24-bit LVDS
1x UART, 2x I2C, 8x GPIO,
4x Host USB 2.0 port, 1x USB OTG port,
1x micro SD (SDHC),1x SDIO, 1x SATA II,
1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
MIPS EL boards should define CONFIG_USE_PRIVATE_LIBGCC=y to work
with EB-only toolchains like the one from kernel.org. If one do
not globally set CONFIG_USE_PRIVATE_LIBGCC=y, the build fails with:
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_lshrdi3.o)
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): compiled for a big endian system and target is little endian
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o): endianness incompatible with that of the selected emulation
/opt/gcc-4.9.0-nolibc/mips-linux/bin/mips-linux-ld.bfd: failed to merge target specific data of file /opt/gcc-4.9.0-nolibc/mips-linux/bin/../lib/gcc/mips-linux/4.9.0/libgcc.a(_ashldi3.o)
/work/git-trees/u-boot-mips/Makefile:1171: recipe for target 'u-boot' failed
One example for a failing build is Travis CI.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Purna Chandra Mandal <purna.mandal@microchip.com>
This introduces some minor cleanups, regarding aspects such as board name, code
and headers organization as well as deprecated and missing config options.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The chains of "depends on <SoC_name>" in the current Kconfig is
clumsy. The idea here is to allow users to choose a SoC group first
(SoC group consists of some SoCs that can coexist in one binary).
Then, allow to enable/disable each SoC support in the selected SoC
group. This makes the Kconfig menu clearer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
PH1-Pro5 support and ProXstream2/PH1-LD6b support can coexist in one
image and there is bit more room in SPL to accommodate all of them.
Merge uniphier_pro5_defconfig into uniphier_pxs2_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the driver in all UniPhier defconfig files and add some
needed defines to the common files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Define prompt for cm-t43.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add full support for SPI flash chips to future-proof U-Boot for cm-t43.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_DM_SERIAL to cm_t43_defconfig. This forces us to update the
CONFIG_SYS_NS16550_REG_SIZE value for SPL.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
We drop everything possible things from board headerfiles and replace
this functionality with responsible settings in Kconfig (_defconfig).
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
There is no need to have some specific prompt, so we drop this within
defconfigs.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Tom Rini <trini@konsulko.com>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported
in SD boot now. For the customer's demand, QSPI needs to be supported
in SD boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig
is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig
is used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Convert ls1021aqds_nor_lpuart and ls1021aqds_ddr4_nor_lpuart
to driver model suport. Enable lpuart port driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
SY8106A is a PMIC which is used on the Allwinner
H3 Orange Pi Pc and Plus board. The VOUT1_SEL register is
implemented to set the default V-CPU voltage to 1200 mV.
This driver is required to ensure the SY8106A V-CPU
voltage is set to 1200 mV after a software reset. On cold
boot the default SY8106A output voltage is selected to be
1200 mV by a pair of resistors on the Orange Pi PC and Plus.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Split duart configuration as device tree file. Move /chosen node
out of board commone device tree. Convert ls1021aqds nor and SD
configurations to driver model support (qspi already uses DM).
Enable ns16550 DM serial driver for nor configurations.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Alison Wang <alison.wang@nxp.com>
CC: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
enable dma driver model for am437x_sk_evm as ti-edma3 supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
In current design, if any peripheral was assigned to both A7 and M4,
it will receive ipg_stop or ipg_wait when any of the 2 platforms
enter low power mode. We will have a risk that, if A7 enter wait,
M4 enter stop, peripheral will have chance to get ipg_stop and ipg_wait
asserted same time. Also if M4 enters stop mode, A7 will have no
chance to access the peripheral.
There are 26 peripherals affected by this IC issue:
SIM2(sim2/emvsim2)
SIM1(sim1/emvsim1)
UART1/UART2/UART3/UART4/UART5/UART6/UART7
SAI1/SAI2/SAI3
WDOG1/WDOG2/WDOG3/WDOG4
GPT1/GPT2/GPT3/GPT4
PWM1/PWM2/PWM3/PWM4
ENET1/ENET2
Software Workaround:
The solution is to set the peripherals to Domain0 by A core, since A core
in Domain0. The peripherals which will be used by M4, will be set to Domain1
by M4.
For example, A core set WDOG4 to domain0, but when M4 boots up, M4 will
set WDOG4 to domain1, because M4 will use WDOG4.
So the peripherals are not shared by them. This way requires
the uboot implemented the RDC driver and set the 26 IPs above
to domain 0 only. M4 image will set the M4 to domain 1 and
set peripheral which it will use to domain 1.
This patch enables the CONFIG_IMX_RDC and CONFIG_IMX_BOOTAUX for
i.MX7D SABRESD board, and setup the 26 IP resources to domain 0.
Signed-off-by: Ye.Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This adds basic support to Intel Cougar Canyon 2 board, a board
based on Chief River platform with an Ivy Bridge processor and
a Panther Point chipset.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
ARC core could be configured with different L1 and L2 (AKA SLC) cache
line lengths. At least these values are possible and were really used:
32, 64 or 128 bytes.
Current implementation requires cache line to be selected upon U-Boot
configuration and then it will only work on matching hardware. Indeed
this is quite efficient because cache line length gets hardcoded during
code compilation. But OTOH it makes binary less portable.
With this commit we allow U-Boot to determine real L1 cache line length
early in runtime and use this value later on. This extends portability
of U-Boot binary a lot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
New features for smartweb:
* switch to hush command parser
* change autoboot stop to <ESC><ESC>
* allow to write ethaddr
Signed-off-by: Matthias Michel <matthias.michel@siemens.com>
Reviewed-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Move this option to Kconfig and clean up the header files. Adjust the only
user (the LCD driver) to work with the new driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move this driver over to use driver model. This involves rearranging the
code somewhat. The effect is that everything is run from the probe() method.
Boards which use this are fixed up, but only seaboard is tested.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This option refers only to the tegra20 video driver, so name it as such
to avoid confusion with tegra124.
Also move this option to Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Adjust the driver to use driver model. The SOR becomes a bridge device. We
use the normal simple_panel driver to handle the display itself. We also
need to enable some options such as regulators, PWMs and DM_VIDEO itself.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The UniPhier EHCI driver (drivers/usb/host/ehci-uniphier.c) does
nothing special but set the base address and handle reset/clock.
Since commit 4feefdcfe9 ("usb: add clock support for generic EHCI"),
the generic one (drivers/usb/host/ehci-generic.c) can do those, too.
We no longer need to stick to the dedicated driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add nand driver support for zynqmp. The Nand
controller used in ZynqMP is Arasan Nand Flash
controller.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
[scottwood: Fix checkpatch warning]
Signed-off-by: Scott Wood <oss@buserror.net>
enable net driver model for k2g evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
enable net driver model for k2e evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
enable net driver model for k2l evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
enable net driver model for k2hk evm as keystone_net supports
driver model
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The defconfig patch will enable the the SPL and NAND settings.
The update to Kconfig will allow the SPL to configured in and
built.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The option was renamed to CONFIG_CONSOLE_ROTATION and Rockchip boards
were not updated. However this option is is not needed by default for
Rockchip since we don't need a rotated console for current boards. So just
remove the old option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board uses RTL8169 which is a driver model ethernet driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move some #undef from efi-x86.h to efi-x86_defconfig as these are
already Kconfig options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Let's go with pure DT solution for board's
based on NXP/Freescale Vybrid platform.
- Merge the DT defconfig with non-DT defconfig for Toradex
Colibri VF50/VF61 and drop the non-DT defconfig.
- Update the legacy defconfigs for NXP/Freescale VF610 Tower
Board with DT.
- Update the legacy defconfigs for Phytec phyCORE-vybrid
Board with DT.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.
Signed-off-by: Ye Li <ye.li@nxp.com>
The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
This adds ethernet, TFTP support for PIC32MZ[DA] Starter Kit. Also
custom environment variables/scripts are added to help boot from network.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Enable MMC, SDHCI, FAT_FS support for PIC32MZ[DA] StarterKit.
Also add custom scripts, rules to boot Linux from microSD card.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
This adds support for Microchip PIC32MZ[DA] StarterKit board
based on a PIC32MZ[DA] family of microcontroller.
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Enable this feature so that truetype fonts can be used on the sandbox
console. Update the tests to select the normal/rotated console when needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Enable the U-Boot Driver Model(DM) to use the Freescale QSPI driver.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add lpuart support using the driver model.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move new /chosen node out of the board device tree.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
If the xparameters file contains a LL_TEMAC definition compile its
driver and the net commands.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Define CONFIG_SYS_PROMPT for all Zynq boards
It was removed by:
"kconfig: add config option for shell prompt"
(sha1: 181bd9dc61)
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add PHYLIB and MII dependencies and enable it by default for Microblaze.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Move config option out of board file.
- Remove uartlite address from config file
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Thomas Chou <thomas@wytron.com.tw>
Remove redundant defconfig file. Boot via flash can be configured via
Kconfig.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Remove redundant defconfig file. Boot via flash can be configured via
Kconfig.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Armada XP (MV78260) based theadorable
board. Its equipped with onboard DDR3, UART, ethernet, I2C, SPI NOR,
LCD and SATA (SSD) interfaces / devices.
Two defconfigs are added:
theadorable_defconfig:
The production U-Boot version with a stripped down drivers and feature
list. This removes networking, USB and PCI support.
theadorable_debug_defconfig:
The debugging / testing U-Boot version with full support for all drivers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
According to the Bananapro schematic VDD25-SATA either comes from a
dedicated WL2003E25-5 LTO, or it is connected to LDO4 via a
0 Ohm resistor.
In practice it seems that LDO4 is used, so enable it and set it to 2.5V.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The LDO settings in this defconfig are either wrong (ALDOs must not be 0)
or the same as Kconfig defaults.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enabling CONFIG_DISPLAY breaks building for some architectures
(microblaze-generic), so we disable CONFIG_DISPLAY in Kconfig
by default and enable this option in defconfigs. CONFIG_DISPLAY
depends on CONFIG_I2C_EDID, so add and enable it in defconfigs, too.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Each system controller can have a number to identify it. It can then be
accessed using syscon_get_by_driver_data(). Put this in a shared header
file and update the only current user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We will use a system controller to model the Intel Management Engine. Enable
this for link.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move the init code into the I2C driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing ivybridge code predates the normal multi-core CPU init, and
it is not used. Remove it and add CPU nodes to the device tree so that all
four CPUs are set up. Also enable the 'cpu' command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable these devices using the VOPL video output device. We explicitly
disable VOPB in the device tree to avoid it taking over. Since this device
has an LCD display this comes up by default. If the display fails for some
reason then it will attempt to use HDMI. It is possible to force it to fail
(and thus fall back to HDMI) by puting 'return -EPERM' at the top of
rk_edp_probe(). For now there is no easy way to select between the two.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a feature which speeds up the CPU to full speed in SPL to minimise
boot time. This is only supported for certain boards (at present only
jerry).
Signed-off-by: Simon Glass <sjg@chromium.org>
The current DisplayPort uclass is too specific. The operations it provides
are shared with other types of output devices, such as HDMI and LVDS LCD
displays.
Generalise the uclass so that it can be used with these devices as well.
Adjust the uclass to handle the EDID reading and conversion to
display_timing internally.
Also update nyan-big which is affected by this.
Signed-off-by: Simon Glass <sjg@chromium.org>
To reduce the SPL image size, drop the LED features. Jerry does not have
an LED and we can leave out GPIO support also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use the same peripheral ID for clocks and pinctrl. While this
works it is probably better to use the device tree clock binding ID for
clocks. We can use the clk_get_by_index() function to find this.
Update the clock drivers and the code that uses them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is defined in the device tree in Linux. Copy over the settings so that
this can be used instead of hard-coding the reset line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
Test that text is displayed correctly when the console is rotated.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Move this option to Kconfig. This is quite simple as only sandbox uses the
driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Convert ls1021atwr_nor_lpuart to driver model support. As a start,
enable lpuart serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Acked-by: Simon Glass <sjg@chromium.org>
LPUART is seen on Freescale VF610 and QorIQ Layerscape devices.
Create a Kconfig option and move it to defconfig for all boards
that have this serial driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert ls1021atwr_nor to driver model support. As a start, enable
ns16550 serial port driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Enable timer driver model for dra74_evm_defconfig as omap-timer
supports driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for dra72_evm_defconfig as omap-timer
supports driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am335x_gp_evm as omap-timer supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am335x_boneblack_vboot as
omap-timer supports driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am437x_gp_evm as omap-timer supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable timer driver model for am437x_sk_evm as omap-timer supports
driver model.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On startup, the BeagleBone family of boards can occationally halt at
the U-Boot prompt. Due to U-Boot receiving random data on the usart.
Migrate BeagleBone based boards to use CONFIG_AUTOBOOT_KEYED, user
will now have to enter the <SPACE> key to get to U-Boot prompt
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Craig McQueen <craig.mcqueen@innerrange.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_NET_RANDOM_ETHADDR to generate a random MAC address
when ETHADDR is not set.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is how CONFIG options are defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
For historical reason, CONFIG_SYS_TEXT_BASE has been specified
in various ways:
[1] by board/${VENDOR}/${BOARD}/config.mk
[2] by CONFIG_SYS_EXTRA_OPTIONS
(This was "options" field of boards.cfg before Kconfig conversion)
[3] by include/configs/${BOARD}.h
[4] by configs/${BOARD}_defconfig
Most of M68K boards use either [1] or [2], both of which we want to
deprecate. Switch them into [4], which is the newest way (Kconfig).
We still allow [3] too, because it is still used by many boards and
we expect much time for conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both of these boards are very close to their limit and with some toolchains
such as gcc 5.x are too large. Switch to tiny printf to reclaim some size.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enabling this function always removes some class of string saftey issues.
The size change here in general is about 400 bytes and this seems a reasonable
trade-off.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Peter Robinson <pbrobinson@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
By removing CONFIG_SYS_MALLOC_CLEAR_ON_INIT, the bootup time is a bit
faster.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This is needed for the upcoming ethernet DM conversion of the maxbcm
board. The configuration of the PHY is then extracted from the DT
instead of using the defines from the config header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
