Commit 6af1d41 "smc911x MII made available" was missing a few "const"
qualifiers. Fix the resulting in build warnings:
smc911x.c: In function 'smc911x_initialize':
smc911x.c:297: warning: passing argument 2 of 'miiphy_register' from incompatible pointer type
smc911x.c:297: warning: passing argument 3 of 'miiphy_register' from incompatible pointer type
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Helmut Raiger <helmut.raiger@hale.at>
The driver already had the MII functions, but they have not been
registered using miiphy_register().
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
TX and RX channel numbers programmed as '1' during EMAC
teardown initialization is wrong. This patch fixes the
same by setting channel number to '0' which is used by U-boot.
Signed-off-by: Sugumar Natarajan <sugumar@ti.com>
Signed-off-by: Nagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The PHY driver was too verbose and corrupted the boot message display
like this:
...
Net: TSEC0 connected to Marvell 88E1111S
TSEC1 connected to Marvell 88E1111S
TSEC0, TSEC1
...
Turn printf() into debug() so we het the expected output again:
...
Net: TSEC0, TSEC1
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Built-in Ethernet adapters support setting the mac address by means of a
ethaddr environment variable for each interface (ethaddr, eth1addr, eth2addr).
This adds similar support to the USB network side, using the names
usbethaddr, usbeth1addr, etc. They are kept separate since we don't want
a USB device taking the MAC address of a built-in device or vice versa.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Eric Bénard <eric@eukrea.com>
Recieve/Receive
recieve/receive
Interupt/Interrupt
interupt/interrupt
Addres/Address
addres/address
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Only install der 4xx-EMAC interrupt handlers *after* the core
network driver is registered.
This problem was noticed on the APM Taishan 440GX board, where
the board hung upon bootup after displaying "Net:".
Signed-off-by: Stefan Roese <sr@denx.de>
gen10g_startup() had 2 bugs:
1) It had a boolean logic error in checking the MMD mask, and
always checked all of them.
2) It checked devices which don't actually report link state, which
meant that it would never believe the link was fully up.
Fix the boolean logic, and then mask the MMD mask so only link-reporting
devices are checked.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reported-by: Ed Swarthout <Ed.Swarthout@freescale.com>
When CONFIG_DW_SEARCH_PHY is disabled, the local phy_addr variable
never gets initialized which causes random behavior at runtime and a
gcc warning. So set it by default to the stored phy address.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
Fix commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The ctrl variable is only used when autoneg support is disabled, so only
declare it under those conditions to avoid an unused variable warning.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Reviewed-by: Vipin Kumar <vipin.kumar@st.com>
This patch fixes following compile warning:
---8<---
macb.c: In function 'macb_write_hwaddr':
macb.c:525:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
This patch removes the warning
---8<---
at91_emac.c: In function 'at91emac_write_hwaddr':
at91_emac.c:487:2: warning: dereferencing type-punned pointer will break strict-aliasing rules
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@gmail.com>
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
* Fix: timer.c compile error io.h not found with arm/at91rm9200
* update arm920t/at91 to ATMEL_xxx name scheme
* update arm920t/at91 soc lib
* update at91_emac driver
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
This allows this configuration to be defined differently for some
boards that request it.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
This is needed for the upcoming TFTP server implementation.
This also simplifies PingHandler() and fixes rxhand_f documentation.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
The tsec driver had a bunch of PHY drivers already written. This
converts them all into PHY Lib drivers, and serves as the first
set of PHY drivers for PHY Lib.
While doing that, cleaned up a number of magic numbers (though
not all of them, as PHY vendors like to keep their numbers as
magical as possible). Also, noticed that almost all of the
vitesse/cicada PHYs had the same config/parse/startup functions,
so those have been collapsed into one.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Extends the mii_dev structure to participate in a full-blown MDIO and
PHY driver scheme. The mii_dev structure and miiphy calls are modified
in such a way to allow the original mii command and miiphy
infrastructure to work as before, but also to support a new set of APIs
which allow (among other things) sharing of PHY driver code and 10G support
The mii command will continue to support normal PHY management functions
(Clause 22 of 802.3), but will not be changed to support 10G
(Clause 45).
The basic design is similar to PHY Lib from Linux, but simplified for
U-Boot's network and driver infrastructure.
We now have MDIO drivers and PHY drivers
An MDIO driver provides:
read
write
reset
A PHY driver provides:
(optionally): probe
config - initial setup, starting of auto-negotiation
startup - waiting for AN, and reading link state
shutdown - any cleanup needed
The ethernet drivers interact with the PHY Lib using these functions:
phy_connect()
phy_config()
phy_startup()
phy_shutdown()
Each PHY driver can be configured separately, or all at once using
config_phylib_all_drivers.h (added in the patch which adds the drivers)
We also provide generic drivers for Clause 22 (10/100/1000), and
Clause 45 (10G) PHYs.
We also implement phy_reset(), and call it in phy_connect(). Because
phy_reset() is essentially the same as miiphy_reset, but:
a) must support 10G PHYs, and
b) should use the phylib primitives,
we implement miiphy_reset, using phy_reset(), but only when
CONFIG_PHYLIB is set. Otherwise, we just use the old version. In this
way, we save on compile size, even if we don't manage to save code size.
Pulled ethtool.h and mdio.h from:
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6
782d640afd15af7a1faf01cfe566ca4ac511319d
With many, many deletions so as to enable compilation under u-boot
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
There were a few files which were already using phy_read and phy_write
for their PHY function names. It's only a few places, and the name
seems most appropriate for the high-level abstraction, so let's
rename the other versions to something more specific.
Also, uec_phy.c had a marvell_init function which I renamed to not
conflict with the one in marvell.c
Lastly, uec_phy.c was putting a space between the phy writing
function names, and the open paren, so I fixed that
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This is merely a rearrangement. No changes to the code, except
to remove now-useless declarations.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Add Intel E1000 82574L PCIe card support. Test on MPC8544DS
and MPC8572 board.
Add the missing contact information for future support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes ea20 after 8ef583a035 where
the u-boot custom PHY_ macros were replaced with those of linux/mii.h MII_
definitions except in the RMII support for davinci_emac. Probably also due to
the merge path of changes in 2010.12.
Signed-off-by: Ben Gardiner<bengardiner@nanometrics.ca>
CC: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Use get_timer() the same way as drivers/net/ftgmac100.c
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Reviewed-by: Macpaul Lin <macpaul@gmail.com>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Some CPU needs cache handling. So this patch add the config of
CONFIG_SH_ETHER_CACHE_WRITEBACK, and it calls wback function.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Added arch/arm/cpu/arm926ejs/davinci/et1011c.c for handling
ET1011C gigabit phy. which overrides get_link_speed function
from default implementation. This enables output of 125 MHz
reference clock on SYS_CLK pin.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adds "DaVinci-EMAC" as the name of the device so that
it gets printed as "Using DaVinci-EMAC device"
during network access (dhcp, tftp) instead of empty name
in "Using" statement.This name also gets
reflected in 'ethact' env variable.
Signed-off-by: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Enabling the gigabit was overwriting the
previous configuration by setting up only GIGAFORCE and
GIG bits of MAC control register.
Modified to retain previous configuration while
gigabit enabling.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The eth_device.name field length is limited by NAMESIZE,
which is 16 defined in include/net.h. Unfortunately, two
of the names in lan91c96.c are beyond that.
Signed-off-by: YanJun Yang <yangyj.ee@gmail.com>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The following commit:
commit 46e91674fb
Author: Peter Tyser <ptyser@xes-inc.com>
Date: Tue Nov 3 17:52:07 2009 -0600
tsec: Force TBI PHY to 1000Mbps full duplex in SGMII mode
Removed setting Auto-Neg by default, however this is believed to be
proper default configuration for initialization of the TBI interface.
Instead we explicitly set CONFIG_TSEC_TBICR_SETTINGS for the
XPedite5370 & XPedite5500 boards that use a Broadcomm PHY which require
Auto-Neg to be disabled to function properly.
This addresses a breakage on the P2020 DS & MPC8572 DS boards when used
with an SGMII riser card. We also remove setting
CONFIG_TSEC_TBICR_SETTINGS on the P1_P2_RDB family of boards as now the
default setting is sufficient for them.
Additionally, we clean up the code a bit to remove an unnecessary second
define.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Tested-by: Peter Tyser <ptyser@xes-inc.com>
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.
The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.
Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
