This patch removed obscure restriction on the HW setting of DMA transfers.
Before this change each transaction sent up to 512 bytes (with packet count
equal to 1) for non EP0 transfer.
Now it is possible to setup DMA transaction up to DMA_BUFFER_SIZE.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurement:
Transmission speed: 20.74 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
A set of cache operations (both invalidation and flush) were redundant
in the S3C HS OTG Samsung driver:
1. s3c_udc_ep0_zlp - to transmit EP0's ZLP packets one don't need to flush
the cache (since it is the zero length transmission)
2. s3c_udc_pre_setup and s3c_ep0_complete_out - cache invalidation is not
needed when the buffer for OUT EP0 transmission is setup, since no data
has yet arrived.
Cache cleanups presented above don't contribute much to transmission speed
up, hence shall be regarded as cosmetic changes.
3. setdma_rx - here the s3c UDC driver's internal buffers were invalidated.
This call is not needed anymore since we reuse the buffers passed from
gadgets. This is a key contribution to transmission speed improvement.
Test condition
- test HW + measurement: Trats - Exynos4210 rev.1
- test HW Trats2 - Exynos4412 rev.1
400 MiB compressed rootfs image download with `thor 0 mmc 0`
Measurements:
Base values (without improvement):
Transmission speed: 9.51 MiB/s
After the change:
Transmission speed: 10.15 MiB/s
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The s3c udc driver sends data in a max packet size. Therefore the dcache
invalidate range shall be equal to max packet, not the entire
DMA_BUFFER_SIZE.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch cleans up the Samsung's UDC driver. It replaces several
DEBUG_* macros with debug_cond().
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Merge our duplicate definitions with the common header.
Also fix drivers/usb/gadget/s3c_udc_otg_xfer_dma.c to
use min() instead of min_t() since we remove the latter
from compat.h.
Additionally use memalign() directly as the lin_gadget
specific kmalloc() macro is removed from lin_gadget_compat.h
by this patch.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
The dev->req_config flag was indicating that the forwarded
request needs to perform the usb gadget delayed status.
This is however not needed anymore, so it can be removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Fix:
In file included from s3c_udc_otg.c:216:0:
s3c_udc_otg_xfer_dma.c: In function 'complete_tx':
s3c_udc_otg_xfer_dma.c:280:33: warning: variable 'is_short' set but not used
s3c_udc_otg_xfer_dma.c:280:6: warning: variable 'ep_tsr' set but not used
s3c_udc_otg_xfer_dma.c: In function 's3c_udc_irq':
s3c_udc_otg_xfer_dma.c:469:16: warning: variable 'flags' set but not used
s3c_udc_otg_xfer_dma.c:468:18: warning: variable 'gintmsk' set but not used
s3c_udc_otg_xfer_dma.c: In function 's3c_queue':
s3c_udc_otg_xfer_dma.c:582:14: warning: variable 'gintsts' set but not used
s3c_udc_otg_xfer_dma.c:581:16: warning: variable 'flags' set but not used
s3c_udc_otg_xfer_dma.c: In function 's3c_ep0_read':
s3c_udc_otg_xfer_dma.c:778:6: warning: variable 'ret' set but not used
s3c_udc_otg_xfer_dma.c: In function 's3c_udc_set_halt':
s3c_udc_otg_xfer_dma.c:1020:16: warning: variable 'flags' set but not used
s3c_udc_otg_xfer_dma.c: In function 's3c_ep0_setup':
s3c_udc_otg_xfer_dma.c:1258:13: warning: initialization from incompatible
pointer type [enabled by default]
s3c_udc_otg_xfer_dma.c:1239:16: warning: variable 'is_in' set but not used
s3c_udc_otg_xfer_dma.c:1239:9: warning: variable 'bytes' set but not used
s3c_udc_otg.c: In function 'usb_gadget_register_driver':
s3c_udc_otg.c:292:16: warning: variable 'flags' set but not used
s3c_udc_otg.c: In function 'usb_gadget_unregister_driver':
s3c_udc_otg.c:338:16: warning: variable 'flags' set but not used
s3c_udc_otg.c: In function 's3c_ep_enable':
s3c_udc_otg.c:582:16: warning: variable 'flags' set but not used
s3c_udc_otg.c: In function 's3c_ep_disable':
s3c_udc_otg.c:646:16: warning: variable 'flags' set but not used
s3c_udc_otg.c: In function 's3c_dequeue':
s3c_udc_otg.c:704:16: warning: variable 'flags' set but not used
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
This commit provides UDC driver support for Samsung's SoC
family of processors.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
