This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY
initialization can be reused in kernel without “usb start” command.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The VSC8574 is a quad-port Gigabit Ethernet transceiver with four SerDes
interfaces for quad-port dual media capability. This driver supports SGMII
and QSGMII MAC mode. For now SGMII mode is tested.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
- set proper compatible property name for mEMAC.
- fixed ft_fixup_port for dual-role mEMAC, which will lead to
MAC node disabled incorrectly.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4160 SoC is low power version of T4240. The T4160 combines eight dual
threaded Power Architecture e6500 cores and two memory complexes (CoreNet
platform cache and DDR3 memory controller) with the same high-performance
datapath acceleration, networking, and peripheral bus interfaces.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
T4240 internal UTMI phy is different comparing to previous UTMI PHY
in P3041.
This patch adds USB 2.0 UTMI Dual PHY new memory map and enable it for
T4240.
The phy timing is very sensitive and moving the phy enable code to
cpu_init.c will not work.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
1. fix 10G mac offset by plus 8;
2. add second 10G port info for FM1 & FM2 when init ethernet info;
3. fix 10G lanes name to match lane protocol table;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.
Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.
There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.
Adding several gpios IP is also possible and supported.
For listing gpio configuration please use "gpio status" command
This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A malloc() followed by memset() can be simply replaced by calloc().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
If failed the add_host(), it is reasonable that return value of
add_sdhci().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Without this additional delay, some eMMC don't negotiate properly bus width
Tested on:
- Toshiba THGBM2G8D8FBAIB
- Toshiba THGBM4G4D1HBAR
- Micron MTFC4GMVEA (the one giving the problem)
- Hynix H26M64002BNR
- SanDisk SDIN5E1-32G
Signed-off-by: Davide Bonfanti <davide.bonfanti@bticino.it>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Most of time that MMC driver spends on initializing a device is polling
OCR (operation conditions register). To decouple this polling loop,
device init is split into two parts: The first part fires the OCR query
command, and the second part polls the result. So the caller is now no
longer bound to the OCR-polling delay; he may fire the query, go
somewhere and then come back later for the result.
To use this, call mmc_set_preinit() on any device which needs this.
This can save significant amounts of time on boot (e.g. 200ms) by
hiding the MMC init time behind other init.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
We can use a common global method for calculating minimum of
3 numbers. Put the same in 'common header' and let 'ehci'
use it.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Some legacy RGMII phys don't have in band signaling for the
speed information. so set the RGMII MAC mode according to
the speed got from PHY.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
log2 of the device block size serves as the shift value used to calculate
the block number to read in file systems when implementing avaiable block
sizes.
It is needed quite often in file systems thus it is pre-calculated and
stored in the block device descriptor.
Signed-off-by: Egbert Eich <eich@suse.com>
The number 512 appears quite a bit in the mmc code. Add a constant for this
so that it can be used here and in other parts of the code (e.g. SPL code
which loads from mmc).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
block_read returns unsigned long, so it doesn't make sense to check for
< 0. and neither does marking the header structure as const and then
casting away the constness to load data into it.
Also cleanup some unneeded pointer casting while we're at it.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Reviewed-by: Tom Rini <trini@ti.com>
Watchdog can be used on Microblaze, PPC and Zynq hw designs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@ti.com>
Support to check whether the SD3.0 or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Rommel Custodio <sessyargc@gmail.com>
eMMC vesrion is supported up to v4.5.
But bootloader isn't saw the exact eMMC version.
After applied this patch,
if use the mmcinfo command, then can see the exactly mmc version.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rommel Custodio <sessyargc@gmail.com>
Rework the waiting for transfer completion loop condition
to continue waiting until both Transfer Complete and DMA End
interrupts occur. Checking of DLA bit in Present State register
looks not needed in addition to interrupts status checking,
so it can be removed from the condition. Also, DMA Error
condition is added to the list of data errors, checked in the loop.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
The cache should invalidate the read buffer for
the SD card interface after the transfer complete,
not command-complete.
Tested-by: Andrew Gabbasov <Andrew_Gabbasov@mentor.com>
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The glitch in the SPI clock line, which commit 3cea335c34 (spi: mxc_spi: Fix spi
clock glitch durant reset) solved, is back now and itwas re-introduced by
commit d36b39bf0d (spi: mxc_spi: Fix ECSPI reset handling).
Actually the glitch is happening due to always toggling between slave mode
and master mode by configuring the CHANNEL_MODE bits in this reset function.
Since the spi driver only supports master mode, set the mode for all channels
always to master mode in order to have a stable, "glitch-free" SPI clock line.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a driver for the I2C TPM from Infineon.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
When building for the Sandbox version, the casts in this change are
necessary to avoid compilation issues.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_NAND_ECC_BCH is set use 4-bit error correction code instead of
the 1-bit error correction code on the NAND device.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The syndrome functions should use the page number passed as argument instead of
the page number saved upon NAND_CMD_READ0.
This does not make any difference if the NAND_NO_AUTOINCR option is set, but
otherwise this fixes accesses to the wrong pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The page number indicated in the debug trace of mxc_nand_read_oob_syndrome() did
not match the page being worked on.
By the way, replace the GCC-specific __FUNCTION__ with __func__.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Add some abstraction to NFC definitions so that some parts of the current code
can also be used for future i.MX5 code.
Clean up a few things by the way.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently is_16bit_nand() is a per SoC function and it decides the bus nand
width by reading some boot related registers.
This method works when NAND is the boot medium, but does not work if another
boot medium is used. For example: booting from a SD card and then using NAND
to store the environment variables, would lead to the following error:
NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB
Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.
If it is defined in the board file, then consider 16-bit NAND bus-width,
otherwise assume 8-bit NAND is used.
This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which
states:
nand-bus-width : 8 or 16 bus width if not present 8
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Introduce CONFIG_SYS_NAND_BUSWIDTH_16BIT option so that other NAND controller
drivers could use it when a 16-bit NAND is deployed.
drivers/mtd/nand/ndfc has CONFIG_SYS_NDFC_16BIT, so just rename it, so that
other NAND drivers could reuse the same symbol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The unwind code was not reversing operations correctly and was causing
a hang on any error condition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Support for NAND storage devices to work with the DFU framework.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
