Commit Graph

9 Commits

Author SHA1 Message Date
Anton Vorontsov
300615dc5d uec: add support for Broadcom BCM5481 Gigabit PHY
This patch adds basic support for Broadcom BCM5481 PHY.

RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is
Peter Barada <peterb@logicpd.com>.

Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-03-25 19:16:46 -05:00
Anton Vorontsov
91cdaa3a9d uec: add support for gbit mii status readings
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
2008-03-25 19:16:45 -05:00
Kim Phillips
f30b6154f1 net: uec_phy: actually increment the timeout counter
allow u-boot to recover (and, e.g., switch to another interface) in the
case where a PHY does not report autonegotiation is complete within its
two second timeout value.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-07 12:47:08 -06:00
Kim Phillips
f655adef65 net: uec_phy: handle 88e1111 rev.B2 erratum 5.6
erratum 5.6 states the autoneg completion bit is functional only if the
autoneg bit is asserted.

This fixes any secondarily-issued networking commands on non-gigabit
links on the mpc8360 mds board.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2008-03-02 21:52:15 +01:00
Joakim Tjernlund
84a3047b72 Remove annoying debug printout for PHY less boards.
PHY less board prints out lots of "read wrong ...":
read wrong value : mii_id 3,mii_reg 2, base e0102320
read wrong value : mii_id 3,mii_reg 3, base e0102320
UEC: PHY is Generic MII (ffffffff)
read wrong value : mii_id 3,mii_reg 4, base e0102320
read wrong value : mii_id 3,mii_reg 0, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 1, base e0102320
read wrong value : mii_id 3,mii_reg 5, base e0102320
FSL UEC0: Full Duplex
FSL UEC0: Speed 100BT
FSL UEC0: Link is up
Using FSL UEC0 device

Make this printout depend on UEC_VERBOSE_DEBUG and
remove its definition in uec_phy.c

Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16 16:56:57 -05:00
Kim Phillips
ee62ed3286 net: reduce boot latency on QE UEC based boards
actually polling for PHY autonegotiation to finish enables us to remove the
5 second boot prompt latency present on QE based boards.

call to qe_set_mii_clk_src in init_phy, and mv call to init_phy from
uec_initialize to uec_init by Joakim Tjernlund; autonegotiation wait
code shamelessly stolen from tsec driver.

also rm unused CONFIG_RMII_MODE code.

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-01-16 16:54:20 -05:00
Andy Fleming
da9d4610d7 Add support for UEC to 8568
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2007-08-14 01:47:44 -05:00
Wolfgang Denk
dd520bf314 Code cleanup. 2006-11-30 18:02:20 +01:00
Dave Liu
7737d5c658 mpc83xx: add QE ethernet support
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
2006-11-03 19:42:21 -06:00