Intel iDMA 32-bit controller has 17 bits for the maximum block size value.
Due to nature of the binary number representation the maximum value is
2^17 - 1. The original code misses the latter part in equation.
Fixes: 5e99fde34a ("x86: tangier: Populate CSRT for shared DMA controller")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Per PCI firmware specification the ACPI has to reserve the memory
which is defined as PCI ECAM.
Fixes: 39665beed6 ("x86: tangier: Enable ACPI support for Intel Tangier")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If a crash occurs, show the loaded UEFI images to facilitate analysis.
This is an example output:
=> bootefi 0x1000000
Found 0 disks
Hello world of bugs!
Invalid Opcode (Undefined Opcode)
EIP: 0010:[<06ceb06e>] EFLAGS: 00010206
Original EIP :[<fec9906e>]
EAX: 00000000 EBX: 06cec000 ECX: 00000fd0 EDX: 00000001
ESI: 06ced18a EDI: 07d0fe10 EBP: 07fe27a0 ESP: 07d0fde0
DS: 0018 ES: 0018 FS: 0020 GS: 0018 SS: 0018
CR0: 00000033 CR2: 00000000 CR3: 00000000 CR4: 00000000
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Stack:
0x07d0fde8 : 0x00000000
0x07d0fde4 : 0x06ced040
--->0x07d0fde0 : 0x07fe27a0
0x07d0fddc : 0x00010206
0x07d0fdd8 : 0x00000010
0x07d0fdd4 : 0x06ceb06e
UEFI image [0x06cea000:0x06cf0fff] pc=0x106e '/bug-i386.efi'
### ERROR ### Please RESET the board ###
With the additional information provided by this patch we know that the
problem occurred 0x106e after the load address of bug-i386.efi.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that we are able to get the size of high memory from QEMU,
report its memory range as usable ram.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
At present only size of memory that is below 4GiB is retrieved from
QEMU. Add a function that gets size of memory that is above 4GiB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
This extracts getting memory size logic in dram_init() to a separate
routine qemu_get_low_memory_size(). No functional changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Aiden Park <aiden.park@intel.com>
This patch removes the x86 architecture specific GD flags
(GD_FLG_COLD_BOOT & GD_FLG_WARM_BOOT), as they are not used. Only
GD_FLG_COLD_BOOT is referenced in coreboot.c but assigned in start16.S.
But the coreboot target does not use start16.S at all and boots directly
from the 32-bit start code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This declaration is only used in three files. Although it relates to
malloc() it is actually only used during malloc() init. It uses CONFIG
options including CONFIG_ENV_ADDR which are defined only in environment.h
so this header must be included anyway, for TOTAL_MALLOC_LEN to be
correct.
Nove it to environment.h to simplify the common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Slim Bootloader already calibrated TSC and provides it to U-Boot.
Therefore, U-Boot does not have to re-calibrate TSC.
Configuring tsc_base and clock_rate makes x86 tsc_timer driver bypass
TSC calibration and use the provided TSC frequency.
- Get TSC frequency from performance info hob
- Set tsc_base and clock_rate for tsc_timer driver
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Slim Bootloader provides serial port info thru its HOB list pointer.
All these HOBs are eligible for Slim Bootloader based board only.
- Get serial port information from the serial port info HOB
- Leverage ns16550 driver with slimbootloader specific platform data
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Slim Bootloader provides memory map info thru its HOB list pointer.
Configure memory size and relocation memory from the HOB data, and
provide e820 entries as well.
- Get memory size from the memory map info HOB
- Set available top memory lower than 4GB for U-Boot relocation
- Provide e820 entries from the memory map info HOB
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This slimbootloader CPU type is to enable U-Boot as a payload which
runs on top of Slim Bootloader (https://github.com/slimbootloader).
The Slim Bootloader is designed with multi-stage architecture for
the execution from reset vector to OS booting, and supports QEMU,
Apollolake, Whiskeylake and Coffeelake platforms consuming Intel
FSP (https://github.com/IntelFsp) for silicon initialization
including CAR and memory initialization.
The Slim Bootloader generates new HOB (Hand Off Block) which are
serial port info, memory map info, performance data info and so on,
and passes it to a Payload. U-Boot as a payload will use these HOB
information for basic initialization such as serial console.
As an initial commit,
- Add CONFIG_SYS_SLIMBOOTLOADER to enable slimbootloader CPU type
- Add new arch/x86/cpu/slimbootloader directory with minimum codes
- Get hob_list pointer from Slim Bootloader
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Intel Tangier has a shared DMA controller that, according to Microsoft spec,
has to be presented in CSRT table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
coreboot makes it possible to add own entries into coreboot's
table at a per mainboard basis. As there might be some custom
ones it makes sense to provide a way to process them.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
When TPL finishes it needs to jump to SPL with the stack set up correctly.
Add a function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The early init should only happen once. Update the probe method to
deal with TPL, SPL and U-Boot proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the Makefie rules to ensure that the correct files are built when
TPL is being used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an implementation of arch_cpu_init_f() so that the x86 SPL code builds
and identifies the CPU.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Allow broadwell to build for SPL and include the reference code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present broadwell only supports booting straight into U-Boot proper.
Add a separate init file to boot from SPL into U-Boot proper, and select
it when SPL is in use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we support having 16-bit init be in SPL or U-Boot proper, but
not TPL. Add support for this so that TPL can boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When a previous phase of U-Boot has run we need to adjust the init of
subsequent states to avoid messing up the CPU state.
Add a new version of the start logic for SPL, when it boots from TPL
(start_from tpl.c) and a new version for U-Boot when it boots from SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Split the CPU init into two parts - the 'full' init which happens in the
first U-Boot phase, and the rest of the init that happens on subsequent
stages.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the debug UART is set up in sdram.c which is not the best place
since it has nothing in particular to do with SDRAM. Since we want to
support initing this in SPL too, move it to a common file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: added 'broadwell' tag in the commit title]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present, for broadwell, SDRAM is always set up in U-Boot proper since
the 64-bit mode (which uses SDRAM init in SPL) is not supported.
Update the code to allow SDRAM init in SPL instead so that U-Boot proper
can be loaded into SDRAM and run from there. This allows U-Boot to be
compressed to reduce space, since it is not necessary to run it directly
from flash. It could later allow us to support 64-bit U-Boot on broadwell.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add debugging during SDRAM init so that problems are easier to
diagnose.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We cannot init the CPU fully both than once during a boot. Add a new
function which can be called to figure out the CPU identity, but which
does not change anything. For x86_64, this is empty for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present many of the functions in this file return -1 as an error
number. which is -EPERM. Update the code to use real error numbers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We use binman to build the x86 image now. Update a comment which still
refers to ifdtool.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add support for initing the I2C device and ADSP on broadwell. These are
needed for sound to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the pinctrl probes the PCH but since it only uses it to obtain
a PCI address, this is no necessary. Avoiding this fixes one of the two
co-dependent loops in broadwell.
This driver really should be a proper pinctrl driver, but for now it
remains a syscon device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Application Digital Signal Processor is used for sound processing with
broadwell. Add a driver to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add sound support for link, using the HDA codec implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a way check to whether HD audio is enabled. Use ioctl() to avoid
adding too many unusual operations to PCH.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is unnecessary to use a RAM version GDT for 64-bit U-Boot proper.
In fact we can just use the ROM version directly, which not only
eliminates the risk of being overwritten by application, but also
removes the complexity of patching the cpu_call64().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Before jumping to 64-bit U-Boot proper, SPL copies the cpu_call64()
function to a hardcoded address 0x3000000. This can have potential
conflicts with application usage. Switch the destination address
to be allocated from the heap to avoid such risk.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the 4-level page table base address for 64-bit U-Boot
proper is assigned an address that conflicts with CONFIG_LOADADDR.
Change it to an address within the low memory range instead.
Fixes crashes seen when 'dhcp' on QEMU x86_64 with
"-net nic -net user,tftp=.,bootfile=u-boot".
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Up until now the call to initialize the USB subsystem was hardcoded
for U-Boot running as an EFI payload. This was used to enable the
use of a USB keyboard in the U-Boot shell. However not all boards
might need this functionality. As initializing the USB subsystem can
take a considerable amount of time (several seconds on some boards),
we now initialize the USB subsystem only if U-Boot is configured to
use USB keyboards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Up until now the call to initialize the USB subsystem was hardcoded
for U-Boot running as a coreboot payload. This was used to enable
the use of a USB keyboard in the U-Boot shell. However not all boards
might need this functionality. As initializing the USB subsystem can
take a considerable amount of time (several seconds on some boards),
we now initialize the USB subsystem only if U-Boot is configured to
use USB keyboards.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
There are still systems running which do not have any LAPIC or even
IOAPIC. Responsible MSRs for those do not exist and the systems are
crashing on trying to setup LAPIC.
This commit makes the APIC stuff able to switch off for those boards
which dont' have an LAPIC / IOAPIC.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It turns out commit c0434407b5 broke some boards which have DM CPU
driver with CONFIG_DISPLAY_CPUINFO option on. These boards just fail
to boot when print_cpuinfo() is called during boot.
Fixes: c0434407b5 ("board_f: Use static print_cpuinfo if CONFIG_CPU is active")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
