This patch adds a driver for the built-in GPIO controller of the MPC85XX
SoC (probably supporting other PowerQUICC III SoCs as well).
Each GPIO bank is identified by its own entry in the device tree, i.e.
gpio-controller@fc00 {
#gpio-cells = <2>;
compatible = "fsl,pq3-gpio";
reg = <0xfc00 0x100>
}
By default, each bank is assumed to have 32 GPIOs, but the ngpios
setting is honored, so the number of GPIOs for each bank in configurable
to match the actual GPIO count of the SoC (e.g. the 32/32/23 banks of
the P1022 SoC).
The usual functions of GPIO drivers (setting input/output mode and output
value setting) are supported.
The driver has been tested on MPC85XX, but it is likely that other
PowerQUICC III devices will work as well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Replace a number of array length calculations with the ARRAY_SIZE()
macro, for clarity.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: York Sun <york.sun@nxp.com>
Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT:
config OF_BOARD_SETUP
bool "Set up board-specific details in device tree before boot"
depends on OF_LIBFDT
...
remove superfluous tests of CONFIG_OF_LIBFDT when testing for
CONFIG_OF_BOARD_SETUP.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
[trini: Typo fix: s/ifdefi/ifdef/]
Signed-off-by: Tom Rini <trini@konsulko.com>
While enabling L2 cache, the value of L2PE (L2 cache parity/ECC
error checking enable) must not be changed while the L2 cache is
enabled.
So, L2PE must be set before enabling L2 cache.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Commit ac337168a unified functions to flush and invalidate dcache by
range. These two functions were no-op for SoCs other than 4xx and
MPC86xx. Adding these functions seemed to be correct but introduced
issues when the dcache is flushed. While the root cause is under
investigation, disable these functions for affected SoCs so various
drivers can work.
Signed-off-by: York Sun <york.sun@nxp.com>
For SoCs that contain multiple SEC engines, each of them needs
to be initialized (by means of initializing among others the
random number generator).
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SOCs, specifically the ones in the C29x familiy can have
multiple security engines. This patch adds a system configuration
define which indicates the maximum number of SEC engines that
can be found on a SoC.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
To enable DM on MPC85xx, we need pre-relocation malloc, which is
implemented in this patch.
We also make sure that the IVORs are always 4-aligned on e500 to prevent
alignment exceptions caused by code changes in start.S.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
Kconfig options must defined in the defconfig files. Since RSA_SOFTWARE_EXP
relies on CONFIG_DM, unless it is set in kconfig we cannot enable RSA.
Remove the hacks which enable CONFIG_DM in header files and update the
defconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not only powerpc/mpc85xx but also Freescale Layerscape platforms will
use fdt_fixup_fman_firmware() to insert Fman ucode blob into the device
tree. So move the function to Fman driver code.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As the QE firmware struct is shared with Fman, move the header file
out of drivers/qe/.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
PAMU driver basic support for usage in Secure Boot.
In secure boot PAMU is not in bypass mode. Hence to use
any peripheral (SEC Job ring in our case), PAMU has to be
configured.
The patch reverts commit 7cad2e38d6.
The Header file pamu.h and few functions in driver have been derived
from Freescale Libos.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Chain of Trust is enabled for PowerPC platforms for Secure Boot.
CONFIG_BOARD_LATE_INIT is defined.
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
bootdelay = 0 (To disable Boot Prompt)
bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A function is created to detrmine if the boot mode is secure
or non-secure for differnt SoC's.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
There are two phases in Secure Boot
1. ISBC: In BootROM, validate the BootLoader (U-Boot).
2. ESBC: In U-Boot, continuing the Chain of Trust by
validating and booting LINUX.
For ESBC phase, there is no difference in SoC's based on ARM or
PowerPC cores.
But the exit conditions after ISBC phase i.e. entry conditions for
U-Boot are different for ARM and PowerPC.
PowerPC:
If Secure Boot is executed, a separate U-Boot target is required
which must be compiled with a diffrent Text Base as compared to
Non-Secure Boot. There are some LAW and TLB settings which are
required specifically for Secure Boot scenario.
ARM:
ARM based SoC's have a fixed memory map and exit conditions from
BootROM are same irrespective of boot mode (Secure or Non-Secure).
Thus the current Secure Boot functionlity has been split into
two parts:
CONFIG_CHAIN_OF_TRUST
This will have the following functionality as part of U-Boot:
1. Enable commands like esbc_validate, esbc_halt
2. Change the environment settings based on bootmode, determined
at run time:
- If bootmode is non-secure, no change
- If bootmode is secure, set the following:
- bootdelay = 0 (Don't give boot prompt)
- bootcmd = Validate and execute the bootscript.
CONFIG_SECURE_BOOT
This is defined only for creating a different compile time target
for secure boot.
Traditionally, both these functionalities were defined under
CONFIG_SECURE_BOOT. This patch is aimed at removing the requirement
for a separate Secure Boot target for ARM based SoC's.
CONFIG_CHAIN_OF_TRUST will be defined and boot mode will be
determine at run time.
Another Security Requirement for running CHAIN_OF_TRUST is that
U-Boot environemnt must not be picked from flash/external memory.
This cannot be done based on bootmode at run time in current U-Boot
architecture. Once this dependency is resolved, no separate
SECURE_BOOT target will be required for ARM based SoC's.
Currently, the only code under CONFIG_SECURE_BOOT for ARM SoC's is
defining CONFIG_ENV_IS_NOWHERE
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_CMD_BLOB must be defined in case of Secure Boot. It was
earlier defined in all config files. The definition has been
moved to a common file which is included by all configs.
Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
xilinx_uartlite has been ported to DM, this patch makes the
xilinx-ppc405-generic and the xilinx-ppc440-generic boards use the new
DM driver.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Add device tree example file for xilinx-ppc440-generic and
xilinx-ppc405-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
The old mail address will stop working soon.
Update it all the files
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of xilinx-ppc440
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
It is just a specialized version of the xilinx-ppc405
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
ml507 is just a specialized version of the xilinx-ppc440-generic
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Incorrect DDR law was created in case of B4860qds after commit
2d2f490d. Return value of ffs64() differs from __ffs64(), eg.
ffs64(0x80000000) = 0x20
__ffs64(0x80000000) = 0x1f
As a result of this change, callers need to adjust the expected
return value by removing -1.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.
So Move set_liodns() and setup_portals() to common u-boot boot
sequence
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Erratum A-009663 workaround requires to set DDR_INTERVAL[BSTOPRE] to 0
before setting DDR_SDRAM_CFG[MEM_EN] and set DDR_INTERVAL[BSTOPRE]
to the desired value after DDR initialization has completed.
When DDR controller is configured to operate in auto-precharge
mode(DDR_INTERVAL[BSTOPRE]=0), this workaround is not needed.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
clang-3.8 reports that serial_putc_raw_dev in serial_ns16550.c is
unused. Further investigation shows that we have 3 places that
implement this function and no callers, remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For compatibility clang will report some gcc version. However since we
are checking gcc versions in order to then fail to build, we should
limit these tests only to when we are using gcc and not clang.
Signed-off-by: Tom Rini <trini@konsulko.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_init_f_mem() alters the C runtime environment's
stack it is actually already using. This is not a valid
behaviour within a C runtime environment.
Split board_init_f_mem into C functions which do not alter
their own stack and always behave properly with respect to
their C runtime environment.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
since:
commit: f05ad9ba "Add a way to skip relocation"
tqm5200s board fails to boot. Reason is that
board_init_f has a function parameter bootflag,
which is not setup in
in arch/powerpc/cpu/mpc5xxx/start.S _start
So board_init_f gets a undefined bootflag,
currently the gd pointer address. Unfortunately
this address sets the GD_FLG_SKIP_RELOC bit,
so u-boot code gets not relocated and u-boot
does not boot ...
Init bootflag with 0, and tqm5200 boots fine again.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <yorksun@freescale.com>
GCC 5.x does not like sizeof(array_variable) and errors out. Change these
calls to be instead sizeof(u8) (as that's what serdes_prtcl_map is) *
SERDES_PRCTL_COUNT (the number of array elements).
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move arch/powerpc/include/asm/fsl_errata.h to include/fsl_errata.h
to make it public for both ARM and POWER SoCs.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix soc.h path in fsl_errata.h]
Reviewed-by: York Sun <yorksun@freescale.com>
In preparation of some new Liebherr boards to be added soon, a new
"liebherr" vendor directory gets created, and the "lwmon5" board
directory is moved into this new vendor directory.
cc: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>