Now that we track which TLB CAM entries are used we can allocate
entries on the fly. Change the SPD DDR TLB setup code to assume
we use at most 8 TLBs (or the number free, which ever is fewer).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to track which TLB CAM entries are used to allow us to
"dynamically" allocate entries later in the code. For example the SPD
DDR code today hard codes which TLB entries it uses. We can now make
that pick entries that are free.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We were incorrectly use the max CAM size as the number of entries in
the array for setting up the addrmap. We should be using the NENTRY
field which is the low 12-bits of TLB1CFG.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536E is capable of booting form NAND/eSDHC/eSPI, this patch
implements these three bootup methods in a unified way - all of these
use the general cpu/mpc85xx/start.S, and load the main image to L2SRAM
which lets us use the SPD to initialize the SDRAM.
For all three bootup methods, the bootup process can be divided into two
stages: the first stage will initialize the corresponding controller,
configure the L2SRAM, then copy the second stage image to L2SRAM and
jump to it. The second stage image is just like the general U-Boot image
to configure all the hardware and boot up to U-Boot command line.
When boot from NAND, the eLBC controller will first load the first stage
image to internal 4K RAM buffer because it's also stored on the NAND
flash. The first stage image, also call 4K NAND loader, will initialize
the L2SRAM, load the second stage image to L2SRAM and jump to it. The 4K
NAND loader's code comes from the corresponding nand_spl directory, along
with the code twisted by CONFIG_NAND_SPL.
When boot from eSDHC/eSPI, there's no such a first stage image because
the CPU ROM code does the same work. It will initialize the L2SRAM
according to the config addr/word pairs on the fixed address and
initialize the eSDHC/eSPI controller, then load the second stage image
to L2SRAM and jump to it.
The macro CONFIG_SYS_RAMBOOT is used to control the code to produce the
second stage image for all different bootup methods. It's set in the
board config file when one of the bootup methods above is selected.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we move some of the functions in tlb.c around we need less
ifdefs. The first stage loader just needs invalidate_tlb and
init_tlbs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can pack the initial tlb_table in MAS register format and use
write_tlb to set things up. This savings can be helpful for NAND
style first stage boot loaders.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Factor out the code we use to actually write a tlb entry.
set_tlb is a logical view of the TLB while write_tlb is a low level
matching the MAS registers.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Its reset value is random, and we sometimes read uninitialized TLB
arrays. Make sure that we don't retain MAS8 from reading such an entry
if the VF bit in MAS8 is set, attempts to use the mapping will trap.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Allow us to search the TLB array based on an address. This is useful
if we want to change an entry but dont know where it happens to be
located.
For example, the boot page mapping we use on MP or the flash TLB that
we change the WIMGE settings for after we've relocated.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we init the addrmap based on the TLB we will not end up getting
the TLB that covers memory if we are using SPD. The reason is we
haven't relocated at the point that we setup the memory TLB and thus it
will not get setup in the addrmap.
Instead we can just walk over the TLB array after we've relocated and
see all the TLBs that have been set and use that information to populate
the initial addrmap. By doing this we insure that we get the TLB
entries that cover memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MAXSIZE field in the TLB1CFG register is 4 bits, not 8 bits.
This made setup_ddr_tlbs() try to set up a TLB larger than the e500 maximum
(256 MB)
which made u-boot hang in board_init_f() when trying to create a new stack
in RAM.
I have an mpc8540 with one 1GB dimm.
Signed-off-by: Fredrik Arnerup <fredrik.arnerup@edgeware.tv>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Previously we only allowed power-of-two memory sizes and didnt
handle >2G of memory. Now we will map up to CONFIG_MAX_MEM_MAPPED
and should properly handle any size that we can make in the TLBs
we have available to us
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
So that we can locate the DDR tlb start entry to the value other than 8. By
default, it is still 8.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Now that all boards have been converted, remove old config code and the
config option for the new style.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a set of functions to manipulate TLB entries:
* set_tlb() - write a tlb entry
* invalidate_tlb() - invalidate a tlb array
* disable_tlb() - disable a variable size tlb entry
* init_tlbs() - setup initial tlbs based on static table
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
