In Allwinner's SDK the A80 is clocked to 1008 MHz by default.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The A80 can support 8-bit eMMC with reset on the PC pingroups.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that DRAM initialization and clock setup is supported,
we can enable SPL for the A80.
[wens@csie.org: Added commit message]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds DRAM initialisation code for sun9i, which calculates the
appropriate timings based on timing information for the supplied
DDR3 bin and the clock speeds used.
With this DRAM setup, we have verified DDR3 clocks of up to 792MHz
(i.e. DDR3-1600) on the A80-Q7 using a dual-channel configuration.
[wens@csie.org: Moved dram_sun9i.c to arch/arm/mach-sunxi/; style cleanup]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
[hdegoede@redhat.com: Drop some huge non-documenting #if 0 ... #endif blocks]
[hdegoede@redhat.com: Fix checkpatch warnings]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Enable an early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
If 'ethaddr' is not set, we will get the ethernet address from AT24MAC,
and set it to 'ethaddr' variable.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Songjun Wu <songjun.wu@microchip.com>
Reviewed-by: Andreas Bießmann <biessmann@corscience.de>
Since the introduction of pinctrl and clk driver, and the dts file,
remove unneeded the pin configurations and the clock enabling code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Move the config options from the include/configs/sama5d2_xplained.h
to configs/sama5d2_xplained_*_defconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Adding new handoff for SDRAM ctrcfg.extratime1 which is
required for stable LPDDR2 operation. Since the board is
using DDR3, the handoff is set to default value 0.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
i.CoreM6 Quad/Dual modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DQ, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU NXP i.MX6 DL, 800MHz
RAM 1GB, 32, 64 bit, DDR3-800/1066
NAND SLC,512MB
Power supply Single 5V
MAX LCD RES FULLHD
and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6SOLO rev1.3 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM: 256 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
Booting using the fdt blob at 0x18000000
Using Device Tree in place at 18000000, end 1800a787
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------
U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1
U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)
CPU: Freescale i.MX6Q rev1.2 at 792MHz
CPU: Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
icorem6qdl>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add plugin code for mx6ullevk.
Define CONFIG_USE_IMXIMG_PLUGIN in defconfig file to use plugin code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
This should be defined in a header file so that arguments are checked.
Move it to video.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most armv8 systems have PSCI support enabled in EL3, either through
ARM Trusted Firmware or other firmware.
On these systems, we do not need to implement system reset manually,
but can instead rely on higher level firmware to deal with it.
The exclude list seems excessive right now, but NXP is working on
providing an in-tree PSCI implementation, so that all NXP systems
can eventually use PSCI as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: fix meson]
Reviewed-by: Simon Glass <sjg@chromium.org>
All systems that are running on armv8 are running bare metal with firmware
that implements PSCI running in EL3. That means we don't really need to expose
the hypercall variants of them.
This patch leaves the code in, but makes the code explicit enough to have the
compiler optimize it out. With this we don't need to worry about hvc vs smc
calling convention when calling psci helper functions.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a README to explain the steps for booting mx6sabresd in different ways:
1. Booting via Normal U-Boot (u-boot.imx)
2. Booting via SPL (SPL and u-boot.img)
3. Booting via Falcon mode (SPL launches the kernel directly)
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Allow i.MX6Q Sabre SD to load the kernel and dtb via SPL in Falcon mode.
Based on the Falcon mode code for MX6 Gateworks Ventana board.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Declaring a CSF section makes the imximage tool increase the size of
data to be loaded by the BootROM and also adds a pointer to that CSF
section in the IVT header to the BootROM can check the signature.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
PBL flush command is restricted to CCSR memory space. So use WAIT
PBI command to provide enough time for data to get flush in
target memory.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York Sun: rewrap commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
T series boards use unified RCW for sd, spi and nand boot.
Now split txxx_rcw.cfg to txxx_sd_rcw.cfg, txxx_spi_rcw.cfg
and txxx_nand_rcw.cfg for SPI/NAND/SD boot.
And modify RCW[PBI_SRC] for them:
PBI_SRC=5 for SPI 24-bit addressing
PBI_SRC=6 for SD boot
PBI_SRC=14 for IFC NAND boot
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Ethernet ports might be used in the kernel even if CPSW driver
is disabled at u-boot. So always set ethaddr and eth1addr
environment variable from efuse.
Retain usbnet_devaddr as it is required for SPL USB eth boot.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Both ethernet ports can be used as CPSW ethernet (RMII mode)
or PRU ethernet (MII mode) by setting the jumper near the port.
Read the jumper value and set the pinmux, external mux and
PHY clock accordingly.
As jumper line is overridden by PHY RX_DV pin immediately
after bootstrap (power-up/reset), we have to use GPIO edge
detection to capture the jumper line status.
As u-boot doesn't provide any infrastructure for GPIO edge
detection, we directly access the GPIO registers.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Create a Kconfig entry for DISPLAY_BOARDINFO and make it be the default
in certain architectures. Migrate all config files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds a small README to explain the 2 defconfig files and its
usage for the different console UART options.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Synology DS109 is based on MV88F6281. The code
is based on Dreamplug code with modificatons
from Synologys open source repository.
Signed-off-by: Walter Schweizer <swwa@users.sourceforge.net>
Signed-off-by: Stefan Roese <sr@denx.de>
As a standard practice complex definitions should be protected
with parentheses, as it might fail when used in a complex if
statements.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add DTS support for dra72 evm Rev C which has the following
changes
* Two ethernet ports now instead of the single one in rev B.
* DP83867 ethernet phy instead of DP838865.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit f225d39d30 ("vexpress: Check TC2 firmware support before defaulting
to nonsec booting") added support to check if the firmware on TC2 is
configured appropriately before booting in nonsec/hyp mode.
However when booting in non-secure/hyp mode, CCI control must be done in
secure firmware and can't be done in non-secure/hyp mode. In order to
ensure that, this patch disables the cci slave port inteface so that it
is not accessed at all.
Cc: Jon Medhurst <tixy@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Jon Medhurst <tixy@linaro.org>
Tested-by: Jon Medhurst <tixy@linaro.org>
We now use device tree to provide SoC data to the UART driver, there
is no need for the legancy UART platform data.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Fix various misspellings of:
* deprecated
* partition
* preceding,preceded
* preparation
* its versus it's
* export
* existing
* scenario
* redundant
* remaining
* value
* architecture
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present there are two SPI functions only used by freescale which are
defined in the spi_flash.h header. One function name matches an existing
generic SPL function.
Move these into a private header to avoid confusion.
Arcturus looks like it does not actually support SPI, so drop the SPI code
from that board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update the API's for transition of Security Monitor states. Instead
of providing both initial and final states for transition, just
provide final state for transition as Security Monitor driver will
take care of it internally.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[York Sun: Reformatted commit message slightly]
Reviewed-by: York Sun <york.sun@nxp.com>
PCM052 SoMs may be equipped with various sizes of DDR.
Keep default of 256MB; new PCM052-based targets will
specify their actual DDR size.
Linux command line is auto-adjusted to DDR size.
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.
Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)
CPU: Freescale i.MX6ULL rev1.0 at 396MHz
CPU: Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM: 512 MiB
MMC: initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When using SPL on i.mx6 we frequently notice some DDR initialization
mismatches between the SPL code and the non-SPL code.
This causes stability issues like the ones reported at 7dbda25ecd
("mx6ul_14x14_evk: Pass refsel and refr fields to avoid hang") and also:
http://lists.denx.de/pipermail/u-boot/2016-September/266355.html .
As the non-SPL code have been tested for long time and proves to be reliable,
let's configure the DDR in the exact same way as the non-SPL case.
The idea is simple: just use the DCD table and write directly to the DDR
registers.
Retrieved the DCD tables from:
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg
and
board/freescale/mx6sabresd/mx6qp.cfg
(NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga)
This method makes it easier for people converting from non-SPL to SPL code.
Other benefit is that the SPL binary size is reduced from 44 kB to 39.9 kB.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
A kernel hang is observed when running wandboard 3.14 kernel and
going to the lowest operational point of cpufreq:
# ifconfig eth0 down
# echo 1 > /sys/class/graphics/fb0/blank
The problem is caused by incorrect setting of the REFR field
of register MDREF. Setting it to 4 refresh commands per refresh
cycle fixes the hang.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
When CONFIG_FIT_IMAGE_POST_PROCESS or CONFIG_SPL_FIT_IMAGE_POST_PROCESS
is enabled board_fit_image_post_process will be called, add this
function to am33xx boards when CONFIG_TI_SECURE_DEVICE is set to
verify the loaded image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
rockchip platform have a protocol to pass the the kernel reboot mode to bootloader
by some special registers when system reboot. In bootloader we should read it and take action.
We can only setup boot_mode in board_late_init becasue "setenv" need env setuped.
So add CONFIG_BOARD_LATE_INIT to common header and use a entry "rk_board_late_init"
to replace "board_late_init" in board file.
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The latest rk3288-miniarm board doesn't have eMMC device, so remove it.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add vdd_center pwm regulator get_device to
enable this regulator.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
EEC is being enabled based on the ddr size populated by SPD data.
But not all keystone platforms have SPD data to detect ddr3 size.
So, enable ECC using the detected DDR size.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function fdt_fixup_dr_usb is specific to fsl/nxp. So,
make the function name explicit and rename fdt_fixup_dr_usb
into fsl_fdt_fixup_dr_usb.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Commit ce02a71c23 "tegra: dts: Sync tegra20 device tree files with
Linux" enabled the ULPI USB port on Ventana, but made no attempt to ensure
that U-Boot code could handle this. In practice, various code is missing,
and various configuration options are not enabled, which causes U-Boot to
hang when attempting to initialize this USB port. This patch enables ULPI
PHY support on Ventana, and adds the required pinmux setup for the port to
operate. Note that Ventana is so similar to Seaboard that this change is
made in the Seaboard board file, which is shared with Ventana.
Seaboard also has the ULPI USB port wired up in hardware, although to an
internal port that often doesn't have anything attached to it. However,
the DT nodes for the USB controller and PHY had different status property
values, so the port was not initialized by U-Boot. Fix this inconsistency,
and enable the ULPI port, just like in the Linux kernel DT. This likewise
requires enabling ULPI support in the Seaboard defconfig.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds basic support for the Marvell Armada 7K DB-88F7040
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- USB
- SATA / AHCI
Support for other interfaces will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds basic support for the Marvell Armada 3700 DB-88F3720
development board. Supported are the following interfaces:
- UART
- SPI (incl. SPI NOR)
- I2C
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Instead of using multiple macros, a data structure is used to pass
board-specific parameters to MMDC DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board is a plug in card for Marvell's switch system development
kits. Form-factor aside it is similar to the DB-88F6820-GP with the
following differences.
- TCLK is 200MHz
- SPI1 is used
- No SATA
- No MMC
- NAND flash
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Use a board-specific board_sat_r_get() function to configure the board
for PCIe 2.0 capability (e.g. 5GB/s link speed). Otherwise the default
of 2.5GB/s will be established.
Signed-off-by: Stefan Roese <sr@denx.de>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
We are supposed to use #include <...> to include headers in the
public include paths. We should use #include "..." only for headers
in local directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rk3399 using one gpio control signal for two usb 2.0 host port,
it's better to enable the power in board file instead of in usb driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no interrupt line for each PWM which used by pinctrl to get the
periph_id, so it's not able to enable the default pinctrl setting by pinctrl
framework, let's enable it at board_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Chip ID needs to be known for loading bitstream because
U-Boot checks ID from bitstream header in BIT format.
BIN format is completely unchecked.
The chipid is get from ATF via SMC.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPL needs to have bigger stack size because of USB.
Simple malloc needs to be disabled because dfu code requires different
allocation functions. There is no space in OCM that's why random place
in DDR is used.
BOOTD must be disabled because it is causing compilation error.
All variables are disabled and used only variables valid for DFU because
they are simple huge. Including automatic variables added by
CONFIG_ENV_VARS_UBOOT_CONFIG.
Hardcode addresses for u-boot, atf, kernel and dtb
just for SPL DFU code.
Enable SPL DFU for zcu100.
Create new usb_dfu_spl variable just to run Linux kernel loaded in SPL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Function is defined in g_dnl.h and have different parameter
then it is used. This patch fixes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
