Backend driver for MUSB OTG controllers found on TI AM35x.
It seems that on AM35X interrupt status registers can be updated
_before_ core registers. As we don't use true interrupts in U-Boot
and poll interrupt status registers instead this can result in
interrupt handler being called with non-updated core registers.
This confuses the code and result in hanged transfers.
Add a small delay in am35x_interrupt as a workaround.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Backend driver for MUSB OTG controllers found on TI AM33xx and
TI81xx SoCs (tested with AM33xx only).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Existing U-Boot musb driver has no support for the new gadget framework
and also seems to have other limitations. As gadget framework is ported
from Linux it seems pretty natural to port musb gadget driver as well.
This driver supports both host and peripheral modes.
This is not a replacement for current musb driver (at least now) as
there are still some consumers of the old UDC interface.
No DMA operation support included, CONFIG_MUSB_PIO_ONLY should be
defined.
Virtual root hub device is not implemented.
Known problems: with no devices connected usb_lowlevel_start() fails.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Enable USB keyboard for seaboard and ventana
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Move environment settings for stdin/stdout/stderr to
tegra-common-post.h and generate them automaticaly based on input
device selection.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
CONFIG_EHCI_DCACHE was removed by commit b8adb12
"USB: Drop cache flush bloat in EHCI-HCD". Remove the defines from
the boards configs as well.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
cc: Marek Vasut <marex@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Tom Rini <trini@ti.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Thierry Reding <thierry.reding@avionic-design.de>
cc: Tom Warren <twarren@nvidia.com>
cc: Stephen Warren <swarren@nvidia.com>
cc: Stefano Babic <sbabic@denx.de>
Modify tegra-common-post.h's BOOTCOMMAND definition to use the generic
filesystem command load rather than separate fatload and ext2load.
This removes the need to iterate over supported filesystem types in the
boot command.
This requires editing all board config headers to enable the new
commands. The now-unused commands are left enabled to assue backwards
compatibility with any user scripts. Boards (all from Avionic Design)
which define custom BOOTCOMMAND values are not affected.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
tegra generic fs cmds fixup
Signed-off-by: Tom Warren <twarren@nvidia.com>
The NAND defines ended up before this include file, but should be after
it, so it doesn't become a post-pre-NAND.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that we are using the new CONFIG_SYS_NAND_SELF_INIT setup, we don't
need CONFIG_SYS_NAND_BASE. Punt it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
TrimSlice's USB1 port has two purposes; it either acts as a device port
hosting Tegra's USB recovery protocol, or acts as a host port connected
to the internal USB->SATA bridge chip, which may in turn be connected to
an SSD or HDD. Add the appropriate device tree and board configuration
options to enable this port as a host port, and route the port to the
SATA bridge using the VBUS GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable the Seaboard's 16-bit LCD and use it as the console.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For tegra we want to enable the cache for the LCD. This is easier if
we can avoid using L2 page tages, so align the LCD to a section
boundary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This provides an option for the LCD to flush the dcache after each update
(puts, scroll or clear).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The normal alignment is PAGE_SIZE, but if this is defined, we can support
other alignments.
The motivation for this change is to make the display section-aligned on
ARM so that we can easily turn off data caching for the frame buffer region
without resorting to level 2 page tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add support for the LCD peripheral at the Tegra2 SOC level. A separate
LCD driver will use this functionality to configure the display.
Signed-off-by: Mayuresh Kulkarni <mkulkarni@nvidia.com>
Mayuresh Kulkarni:
- changes to remove bitfields and clean up for submission
Signed-off-by: Simon Glass <sjg@chromium.org>
Simon Glass:
- simplify code, move clock control into here, clean-up
Signed-off-by: Tom Warren <twarren@nvidia.com>
The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
These platforms don't include dcache support. Define CONFIG_SYS_DCACHE_OFF
so that functions don't try to call non-existent routines like
flush_dcache_range().
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The mx5 lowlevel_init.S contains board-specific code based on the reference
design. Let's keep it since it avoids creating new lowlevel_init files and it
may be used by many boards. But add a config to make it optional in order not to
cause issues on boards not following this part of the reference design.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matt Sealey <matt@genesi-usa.com>
Acked-by: Stefano Babic <sbabic@denx.de>
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
One second is enough time for users to react in case they want to stop the
booting process.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Jason Liu <r64343@freescale.com>
Add support for the OTG port on the mx35pdk Personality board.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The EHCI definitions in i.MX31's imx-regs.h are MXC-generic, so move them to
ehci-fsl.h so that all MXC SoCs can use them.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This patch enables SPI Booting for EXYNOS5
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables SPI driver for EXYNOS5.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch enables sound support for EXYNOS5
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Chander Kashyap <chander.kashyap@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds driver for I2S interface specific to samsung.
Signed-off-by: R. Chandrasekar <rcsekar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add support for display on Universal C210 board.
Width of displyed logo must be not bigger than 480 pixel and
is limited by width of the screen.
Tizen logo size is 520x120 pixels and should be resized.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add LDO7 and LDO17 macros to max8998_pmic.h necessary to power on the LCD.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch use software spi on Samsung Universal C210 board.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Low level initialisation is done by another bootloader
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SDRAM setup alike to ORIGEN Dev board.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- update clock settings for higher perfomance
- change standard baud rate to 115200
- fix flash base address
- remove unused defines
- add I2C support
- switch form board dependent flash to cfi
- remove board dependent flash code
- use sdram bank 0 instead of bank 1 on boot
- enable on board frame buffer instead external
- remove fake mac address form config
- add watchdog support
- add status led support
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
[agust: fixed small style issues and build warning]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Support for TRATS battery has been added. It is treated as a "normal"
power related device and thereof controlled by pmic/power subsystem.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
FG IC built into the MAX8997 device (compliant to MAX17042) is enabled
at TRATS.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
MUIC IC built into the MAX8997 device is enabled at TRATS.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Function for calculating LDO internal register value from passed micro
Volt.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Support for MAX17042 fuel-gauge (FG), which is built into the MAX8997
power management device.
Special file - fg_battery_cell_params.h with cells characteristics
added.
The FG device will work with redesigned PMIC framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Support for MUIC (Micro USB Integrated Circuit) built into the MAX8997
power management device.
The MUIC device will work with redesigned PMIC framework.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Now it is possible to provide specific function per PMIC/power
device instance.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
New power_chrg.h file has been added to "bind" together common
information about charging battery available in the system.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the pmic_reg_read is the u32 value, the order in which bytes
are placed to form u32 value is important.
Support for big and little sensor endianess is added.
Moreover calls to [leXX|beXX]_to_cpu have been added to support
little and big endian SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
When booting a fit image with multiple configurations, the user either has to
specify which configuration to use explicitly, or there has to be a default
defined which is chosen automatically. This change adds an option to change
that behavior so that a configuration can be selected explicitly, or the
configuration which has the device tree that claims to be compatible with the
earliest item in U-Boot's device tree.
In other words, if U-Boot claimed to be compatible with A, B, and then C, and
the configurations claimed to be compatible with A, D and B, D and D, E, the
first configuration, A, D, would be chosen. Both the first and second
configurations match, but the first one matches a more specific entry in
U-Boot's device tree. The order in the kernel's device tree is ignored.
Signed-off-by: Gabe Black <gabeblack@google.com>
Commit-Ready: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add get and set gpio functions to fdtdec that take into account the
polarity field in fdtdec_gpio_state.flags.
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
It decodes a 64-bit value from a property that is at least 8 bytes long.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Commit-Ready: Vincent Palatin <vpalatin@chromium.org>
Commit-Ready: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Samsung's SDHCI bindings require multiple gpios to be parsed and
configured at a time. Export the already available fdtdec_decode_gpios
for this purpose.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Commit-Ready: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
A memory region has a start and a size and is often specified in
a node by a 'reg' property. Add a function to decode this information
from the fdt.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to look up a configuration string such as board name
and returns its value. We look in the "/config" node for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to look up a configuration item such as machine id
and return its value.
Note: The code has been taken as is from the Chromium u-boot development
tree and needs Simon Glass' sign-off.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
implement the common api lcd_setcolreg in include/lcd.h
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[agust: fixed commit log and gcc 4.6 -Wparentheses warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The file has a wrong inline keyword of __led_toggle(), which causes
compilation error. And its content is defined in common status_led.h.
So define CONFIG_BOARD_SPECIFIC_LED in board config files and remove
this header file.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
The commit 51926d5ee0
COMMON: Use __stringify() instead of rest of implementations
forgot to update the wrctl funtion, and causes compilation error.
But there are builtin functions for control registers access in
nios2 comipiler. It is convenient to use them instead.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Cc: Marek Vasut <marex@denx.de>
Use CONFIG_MX6 when the particular processor
variant isn't important.
Reserve the use of CONFIG_MX6Q to
specifically test for quad cores variant.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Flushing caches is necessary because of soft reset
which doesn't clear caches.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Reviewed-by: Marek Vasut <marex@denx.de>
Create a basic API to provide access to lcd parameters such as screen
size, and to position the cursor on the screen.
This matches up with the video API for the same purpose. Unfortunately
they are not yet combined.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a basic API to provide access to video parameters such as screen
size, and to position the cursor on the screen. Also add a prototype
for video_display_bitmap() which was missing.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
define Z_NULL to (void *)0 include/u-boot/zlib.h to get rid of most of
the NULL pointer warnings.
inflate.c:942:1: warning: non-ANSI definition of function 'inflateEnd'
inflate.c:9:1: warning: non-ANSI definition of function 'inflateReset'
inflate.c:12:17: warning: Using plain integer as NULL pointer
inflate.c:12:42: warning: Using plain integer as NULL pointer
inflate.c:15:17: warning: Using plain integer as NULL pointer
inflate.c:21:19: warning: Using plain integer as NULL pointer
inflate.c:35:1: warning: non-ANSI definition of function 'inflateInit2_'
inflate.c:38:20: warning: Using plain integer as NULL pointer
inflate.c:41:17: warning: Using plain integer as NULL pointer
inflate.c:42:17: warning: Using plain integer as NULL pointer
inflate.c:50:18: warning: Using plain integer as NULL pointer
inflate.c:65:23: warning: Using plain integer as NULL pointer
inflate.c:69:21: warning: Using plain integer as NULL pointer
inflate.c:78:1: warning: non-ANSI definition of function 'inflateInit_'
inflate.c:86:1: warning: non-ANSI definition of function 'fixedtables'
inflate.c:108:26: warning: Using plain integer as NULL pointer
inflate.c:109:1: warning: non-ANSI definition of function 'updatewindow'
inflate.c:112:30: warning: Using plain integer as NULL pointer
inflate.c:339:1: warning: non-ANSI definition of function 'inflate'
inflate.c:349:17: warning: Using plain integer as NULL pointer
inflate.c:349:42: warning: Using plain integer as NULL pointer
inflate.c:350:27: warning: Using plain integer as NULL pointer
inflate.c:369:42: warning: Using plain integer as NULL pointer
inflate.c:376:32: warning: Using plain integer as NULL pointer
inflate.c:401:54: warning: Using plain integer as NULL pointer
inflate.c:419:32: warning: Using plain integer as NULL pointer
inflate.c:426:32: warning: Using plain integer as NULL pointer
inflate.c:433:32: warning: Using plain integer as NULL pointer
inflate.c:444:36: warning: Using plain integer as NULL pointer
inflate.c:449:37: warning: Using plain integer as NULL pointer
inflate.c:450:38: warning: Using plain integer as NULL pointer
inflate.c:457:40: warning: Using plain integer as NULL pointer
inflate.c:458:47: warning: Using plain integer as NULL pointer
inflate.c:480:40: warning: Using plain integer as NULL pointer
inflate.c:481:50: warning: Using plain integer as NULL pointer
inflate.c:491:37: warning: Using plain integer as NULL pointer
inflate.c:492:37: warning: Using plain integer as NULL pointer
inflate.c:501:40: warning: Using plain integer as NULL pointer
inflate.c:502:53: warning: Using plain integer as NULL pointer
inflate.c:512:37: warning: Using plain integer as NULL pointer
inflate.c:513:40: warning: Using plain integer as NULL pointer
inflate.c:525:32: warning: Using plain integer as NULL pointer
inflate.c:529:52: warning: Using plain integer as NULL pointer
inflate.c:543:54: warning: Using plain integer as NULL pointer
inflate.c:932:17: warning: Using plain integer as NULL pointer
inflate.c:932:42: warning: Using plain integer as NULL pointer
inflate.c:935:26: warning: Using plain integer as NULL pointer
inflate.c:940:19: warning: Using plain integer as NULL pointer
adler32.c:58:5: warning: non-ANSI definition of function 'adler32'
adler32.c:81:16: warning: Using plain integer as NULL pointer
zutil.c:53:9: warning: non-ANSI definition of function 'zcalloc'
zutil.c:64:9: warning: non-ANSI definition of function 'zcfree'
inffast.c:70:1: warning: non-ANSI definition of function 'inflate_fast'
inftrees.c:33:1: warning: non-ANSI definition of function 'inflate_table'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
bootp.c:44:14: warning: symbol 'dhcp_state' was not declared. Should it be static?
bootp.c:45:15: warning: symbol 'dhcp_leasetime' was not declared. Should it be static?
bootp.c:46:10: warning: symbol 'NetDHCPServerIP' was not declared. Should it be static?
arp.c:30:17: warning: symbol 'NetArpWaitReplyIP' was not declared. Should it be static?
arp.c:37:16: warning: symbol 'NetArpTxPacket' was not declared. Should it be static?
arp.c:38:17: warning: symbol 'NetArpPacketBuf' was not declared. Should it be static?
atheros.c:33:19: warning: symbol 'AR8021_driver' was not declared. Should it be static?
net.c:183:7: warning: symbol 'PktBuf' was not declared. Should it be static?
net.c:159:21: warning: symbol 'net_state' was not declared. Should it be static?
ping.c:73:6: warning: symbol 'ping_start' was not declared. Should it be static?
ping.c:82:13: warning: symbol 'ping_receive' was not declared. Should it be static?
tftp.c:53:7: warning: symbol 'TftpRRQTimeoutMSecs' was not declared. Should it be static?
tftp.c:54:5: warning: symbol 'TftpRRQTimeoutCountMax' was not declared. Should it be static?
eth.c:125:19: warning: symbol 'eth_current' was not declared. Should it be static?
Note: in the ping.c fix, commit a36b12f95a
"net: Move PING out of net.c" mistakenly carried the ifdef CMD_PING
clause from when it was necessary to avoid warnings when it was embedded
in net.c.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
include/linux/unaligned/generic.h:5:9: warning: preprocessor token __force redefined
include/linux/compiler.h:10:10: this was the original definition
fixup __force definitions in compat.h code appears to be placed
there as a cover up from a code import from linux when u-boot didn't yet
have a compiler.h, introduced by commit
b1b4e89a0f "Add LZO decompressor support".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
include/linux/compat.h:4:9: warning: preprocessor token __user redefined
include/linux/compiler.h:7:10: this was the original definition
include/linux/compat.h:5:9: warning: preprocessor token __iomem redefined
include/linux/compiler.h:12:10: this was the original definition
fixup __iomem, __user definitions in compat.h code appears to be placed
there as a cover up from a code import from linux when u-boot didn't yet
have a compiler.h, introduced by commit
932394ac43 "Rewrite of NAND code based on
what is in 2.6.12 Linux kernel".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
When the generic filesystem load command "fsload" was written, I felt
that "load" was too generic of a name for it, since many other similar
commands already existed. However, it turns out that there is already
an "fsload" command, so that name cannot be used. Rename the new
"fsload" to plain "load" to avoid the conflict. At least anyone who's
used a Basic interpreter should feel familiar with the name!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit 045fa1e "fs: add filesystem switch libary, implement ls and
fsload commands" unified the implementation of fatload and ext*load
with the new command fsload. However, this altered the interpretation
of command-line numbers from always being base-16, to requiring a "0x"
prefix for base-16 numbers. Enhance do_fsload() to allow commands to
specify which base to use.
Use base 0, thus requiring a "0x" prefix for the new fsload command.
This feels much cleaner than assuming base 16.
Use base 16 for the pre-existing fatload and ext*load to prevent a
change in behaviour.
Use base 16 exclusively for the loadaddr environment variable, since
that variable is interpreted in multiple places, so we don't want the
behaviour to change.
Update command help text to make it clear where numbers are assumed to
be hex, and where an explicit "0x" prefix is required.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Writes in u-boot are so rare, and the logic to know when is
the last write and do a flush only there is sufficiently
difficult. Just do a flush after every write. This incurs,
usually, one extra flush when the rare writes do happen.
Signed-off-by: Marc Jones <marc.jones@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
In the structure returned by the ATA identify device command, there are two
fields which describe the device capacity. One is a 32 bit data type which
reports the number of sectors as a 28 bit LBA, and the other is a 64 bit data
type which is for a 48 bit LBA. If the device doesn't support 48 bit LBAs,
the small value is the only value with the correct size. If it supports more,
if the number of sectors is small enough to fit into 28 bits, both fields
reflect the correct value. If it's too large, the smaller field has 28 bits of
1s, 0xfffffff, and the other field has the correct value.
The AHCI driver is implemented by attaching to the generic SCSI code and
translating on the fly between SCSI binary data structures and AHCI data
structures. It responds to requests to execute specific SCSI commands by
executing the equivalent AHCI commands and then crafting a response which
matches what a SCSI disk would send.
The AHCI driver now considers both fields and chooses the correct one when
implementing both the SCSI READ CAPACITY (10) and READ CAPACITY (16) commands.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
- print the correct speed
- print all the AHCI capability flags
(information taken from Linux kernel driver)
- clean up some comments
For example, this might show the following string:
AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Commit-Ready: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Reinauer <reinauer@chromium.org>
Add a new function to find out the number of available SCSI disks. Also
set the 'scsidevs' environment variable after each scan.
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This includes were outside an #ifdef CONFIG_PPC, but there is not reason
to exclude powerpc from using them.
Move the declaration outside the #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
We add CONFIG_ENV_VARS_UBOOT_CONFIG,
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG and CONFIG_BOARD_LATE_INIT to set
the variables and then fdtfile and findfdt to make us of this. It is
now possible to do 'run findfdt' to have fdtfile be set to the value of
the dtb file to load for the board we are running on.
Signed-off-by: Tom Rini <trini@ti.com>
CONFIG_ENV_VARS_UBOOT_CONFIG creates environment variables indicating
which configuration U-Boot was built for. Some U-Boot binaries run on
multiple boards, and hence this information may not uniquley describe
the HW that U-Boot is actually running on. Another patch introduces
environment variable board_name to represent that. In order to avoid
scripts having to check $board_name, use it if set, and then fall back
to using $board, make CONFIG_ENV_VARS_UBOOT_CONFIG also set a default
value for board_name, so that variable is always available.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 1db7377a70 fixes the gen_atmel_mci driver
to be able to use multi block access for avr32. Therefore remove the setting
which forces single block access.
This also adds a huge performace gain for mmc access:
---8<---
Loading file "/boot/uImage" from mmc device 0:1
1830666 bytes read in 1293 ms (1.3 MiB/s)
--->8---
vs.
---8<---
Loading file "/boot/uImage" from mmc device 0:1
1830666 bytes read in 237 ms (7.4 MiB/s)
--->8---
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: haavard.skinnemoen@atmel.com
Cc: hans-christian.egtvedt@atmel.com
Cc: mpfj@mimc.co.uk
Cc: alex.raimondi@miromico.ch
Cc: julien.may@miromico.ch
Cc: egtvedt@samfundet.no
Cc: havard@skinnemoen.net
Implement "ls" and "fsload" commands that act like {fat,ext2}{ls,load},
and transparently handle either file-system. This scheme could easily be
extended to other filesystem types; I only didn't do it for zfs because
I don't have any filesystems of that type to test with.
Replace the implementation of {fat,ext[24]}{ls,load} with this new code
too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This makes the FAT and ext4 filesystem implementations build if
CONFIG_FS_{FAT,EXT4} are defined, rather than basing the build on
whether CONFIG_CMD_{FAT,EXT*} are defined. This will allow the
filesystems to be built separately from the filesystem-specific commands
that use them. This paves the way for the creation of filesystem-generic
commands that used the filesystems, without requiring the filesystem-
specific commands.
Minor documentation changes are made for this change.
The new config options are automatically selected by the old config
options to retain backwards-compatibility.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Change tegra SPL to use common SPL framework. Any tegra specific
initialization is now done in spl_board_init() instead of
board_init_f()/board_init_r(). Only one SPL boot target is supported
on tegra, which is boot to RAM image. jump_to_image_no_args() must be
overridden on tegra so the host CPU can be initialized.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For Tegra, the SPL and main U-Boot are concatenated together to form a
single memory image. Hence, the maximum SPL size is the different in
TEXT_BASE for SPL and main U-Boot. Instead of manually calculating
SPL_MAX_SIZE based on those two TEXT_BASE, which can lead to errors if
one TEXT_BASE is changed without updating SPL_MAX_SIZE, simply perform
the calculation automatically.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the missing bits to the Tegra NAND driver to make ONFI detection work
properly.
Also add it to the Tegra default config, as it seems to be a reasonable thing
to have it available on all boards that use any kind of NAND.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The device tree already contains the required configuration for both the
USB1 and USB3 ports. Enable the required configuration options to enable
both these ports, which in turn allows the USB1 port to be used.
Note that on a true Seaboard, this port is typically used as a device
port hosting Tegra's USB recovery protocol. However, on the Springbank
derivative, this port is the only external USB port, so we enable it as
a host port so that USB peripherals may be used. Enabling this port in
U-Boot as a host port doesn't prevent the port from reverting to a
device port when the CPU is reset into recovery mode.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.
* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Currently, Tegra's default environment uses non-standard variables to define
where boot scripts should load the kernel, FDT, and initrd. This change both
changes the variable names to match those described in U-Boot's README, and
shuffles their values around a little so that the values make a little more
sense; see comments in the patch for rationale behind the values chosen.
Note that this patch does remove the old non-standard variable "fdt_load" from
the default environment, so this patch requires people to change their boot
scripts.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This define indicates the size of the memory region where it is safe
to place data passed to the Linux kernel (ATAGs, DTB, initrd). The
value needs to be:
a) Less than or equal to RAM size.
b) Small enough that the area is not within the kernel's highmem region,
since the kernel cannot access ATAGs/DTB/initrd from highmem.
c) Large enough to hold the kernel+DTB+initrd.
256M seems large enough for (c) in most circumstances, and small enough
to satisfy (a) and (b) across any possible Tegra board. Note that the
user can override this value via environment variable "bootm_mapsize"
if needed.
The advantage of defining BOOTMAPSZ is that we no longer need to define
variable fdt_high in the default environment. Previously, we defined
this to prevent the DTB from being relocated to the very end of RAM,
which on most Tegra systems is within highmem, and hence which would
cause boot failures. A user can still define this variable themselves
if they want the FDT to be either left in-place wherever loaded, or
copied to some other specific location. Similarly, there should no
longer be a strict requirement for the user to define initrd_high if
using an initrd.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds board support for the Toradex Colibri T20 module.
Working functions:
- SD card boot
- USB boot
- Network
- NAND environment
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch remove the env saving in NAND as so far the
NAND driver is not ported to the M54418TWR platform.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
These boards have long reached EOL, and there has been no indication
of any active users of such hardware for years. Get rid of the dead
weight.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@denx.de>
SX1 does not build properly by itself, is not built
as part of MAKEALL arm or MAKEALL -a arm, and is only
present in Makefile, not boards.cfg. As it also has no
entry in MAINTAINERS, it is orphan and non-functional.
Remove it.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Recent patches adding FSL_PMIC_I2C_LENGTH require
that the PMIC model is defined.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <jason.hui@linaro.org>
mx25pdk has a Ethernet port that is connected to its internal FEC controller.
In order to power up the Ethernet PHY (DP83640) it is necessary to communicate
with the MC34704 PMIC via I2C.
Make the FEC ethernet port functional
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Introduce FSL_PMIC_I2C_LENGTH to configure the number of bytes that are used to
communicate with the PMIC via I2C.
Instead of hardcoding the value, pass the number via a configurable option per
PMIC type.
This will be useful for adding support for PMIC MC34704 from Freescale, which
uses only one byte in its I2C protocol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx25pdk has a SD/MMC slot connected to esdhc1.
Add support for it and allow the environment variables to be saved into SD/MMC.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
It is necessary to include CONFIG_MX25 as several i.mx drivers handle the SoC
differences based on the this config option.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The woodburn board is based on the MX35 SOC.
Support for both external (NOR) and internal
(SD Card) boot mode are added. It uses the
generic SPL framework to implement the internal boot
mode.
The following peripherals are supported:
- Ethernet (FEC)
- SD Card
- NAND (512 MB)
- NOR Flash
In the internal boot mode, a simple imximage header
is generated to set the address in internal RAM
where the SOC must copy the SPL code. The initial setup
is then demanded to the SPL itself.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add targets of am335x_evm_uart{1,2,3,4,5} to have serial input/output on
UART{1,2,3,4,5} for use with the Beaglebone RS232 cape, am335x_evm
daughterboard, and other custom configurations.
Modify target for am335x_evm to include SERIAL1 and CONS_INDEX=1
options in order to clarify UART selection requirements.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
This makes the FAT filesystem API more consistent with other block-based
filesystems. If in the future standard multi-filesystem commands such as
"ls" or "load" are implemented, having FAT work the same way as other
filesystems will be necessary.
Convert cmd_fat.c to the new API, so the code looks more like other files
implementing the same commands for other filesystems.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Add the required config.mk logic for this SoC as well as the BOOT_DEVICE
define. Finally, enable the options on the am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
Some GPIOs differ in the new revision board.
Previous revision are considered obsolete and
they will not anymore supported.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The mcx board was slightly modified and the pinmux must be updated.
There is no need to support the old board, that becomes obsolete.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add Freescale MCF54418TWR ColdFire development board support.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
Add support for the new kmvect1 board powered by the mpc8309 processor.
As this board is very similar to the existing suvd3, instead of adding a
new config header file, just add a new config option to suvd3.h
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support for Keymile boards based on mpc8309
(it would be only kmvect1 for now)
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
[#elseif -> #if to allow kmcoge5ne and kmeter1 to build successfully]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This processor, though very similar to other members of the
PowerQUICC II Pro family (namely 8308, 8360 and 832x), provides
yet another feature set than any supported sibling.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Introduce a new configuration token CONFIG_MPC830x to be shared among
mpc8308 and mpc8309. Define it for existing 8308 boards, and refactor
existing common code so to make future introduction of 8309 simpler.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Neither cm-t35, nor cm-t3730 is using OneNAND or flash.
Remove the related defines from config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Fix usage of 'mmc rescan' by many configs. Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device. 'mmc rescan' itself does not take any arguments.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
LAN8720 PHY is used on Freescale C2X0QDS board.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Starting from QMan3.0, the QMan clock cycle needs be exposed so that the kernel
driver can use it to calculate the shaper prescaler and rate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The T4240QDS is a high-performance computing evaluation, development and
test platform supporting the T4240 QorIQ Power Architecture™ processor.
SERDES Connections
32 lanes grouped into four 8-lane banks
Two “front side” banks dedicated to Ethernet
Two “back side” banks dedicated to other protocols
DDR Controllers
Three independant 64-bit DDR3 controllers
Supports rates up to 2133 MHz data-rate
Supports two DDR3/DDR3LP UDIMM/RDIMMs per controller
QIXIS System Logic FPGA
Each DDR controller has two DIMM slots. The first slot of each controller
has up to 4 chip selects to support single-, dual- and quad-rank DIMMs.
The second slot has only 2 chip selects to support single- and dual-rank
DIMMs. At any given time, up to total 4 chip selects can be used.
Detail information can be found in doc/README.t4qds
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The multirate ethernet media access controller (mEMAC) interfaces to
10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII
interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface.
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Add support for Freescale T4240 SoC. Feature of T4240 are
(incomplete list):
12 dual-threaded e6500 cores built on Power Architecture® technology
Arranged as clusters of four cores sharing a 2 MB L2 cache.
Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture
v2.06-compliant)
Three levels of instruction: user, supervisor, and hypervisor
1.5 MB CoreNet Platform Cache (CPC)
Hierarchical interconnect fabric
CoreNet fabric supporting coherent and non-coherent transactions with
prioritization and bandwidth allocation amongst CoreNet end-points
1.6 Tbps coherent read bandwidth
Queue Manager (QMan) fabric supporting packet-level queue management and
quality of service scheduling
Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support
Memory prefetch engine (PMan)
Data Path Acceleration Architecture (DPAA) incorporating acceleration for
the following functions:
Packet parsing, classification, and distribution (Frame Manager 1.1)
Queue management for scheduling, packet sequencing, and congestion
management (Queue Manager 1.1)
Hardware buffer management for buffer allocation and de-allocation
(BMan 1.1)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps
RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps
Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps
DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0)
32 SerDes lanes at up to 10.3125 GHz
Ethernet interfaces
Up to four 10 Gbps Ethernet MACs
Up to sixteen 1 Gbps Ethernet MACs
Maximum configuration of 4 x 10 GE + 8 x 1 GE
High-speed peripheral interfaces
Four PCI Express 2.0/3.0 controllers
Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with
Type 11 messaging and Type 9 data streaming support
Interlaken look-aside interface for serial TCAM connection
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Four I2C controllers
Four 2-pin or two 4-pin UARTs
Integrated Flash controller supporting NAND and NOR flash
Two eight-channel DMA engines
Support for hardware virtualization and partitioning enforcement
QorIQ Platform's Trust Architecture 1.1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
The P5040 does not have SRIO, so don't put the SRIO definitions in
corenet_ds.h. They belong in the board-specific header files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
This change adds CBFS support and some commands to use it to u-boot. These
commands are:
cbfsinit - Initialize CBFS support and pull all metadata into RAM. The end of
the ROM is an optional parameter which defaults to the standard 0xffffffff and
can be used to support multiple CBFSes in a system. The last one set up with
cbfsinit is the one that will be used.
cbfsinfo - Print information from the CBFS header.
cbfsls - Print out the size, type, and name of all the files in the current
CBFS. Recognized types are translated into symbolic names.
cbfsload - Load a file from CBFS into memory. Like the similar command for fat
filesystems, you can optionally provide a maximum size.
Support for CBFS is compiled in when the CONFIG_CMD_CBFS option is specified.
The CBFS driver can also be used programmatically from within u-boot.
If u-boot needs something out of CBFS very early before the heap is
configured, it won't be able to use the normal CBFS support which caches some
information in memory it allocates from the heap. The
cbfs_file_find_uncached function searches a CBFS instance without touching
the heap.
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Stefan Reinauer <reinauer@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The size of an LBA type changes depending on this option. We need to
use a different printf() string in each case, so create a define for
this.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
The command declaration now uses the new LG-array method to generate
list of commands. Thus the __u_boot_cmd section is now superseded and
redundant and therefore can be removed. Also, remove externed symbols
associated with this section from include/command.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
This patch converts the old method of creating a list of command
onto the new LG-arrays code. The old u_boot_cmd section is converted
to new u_boot_list_cmd subsection and LG-array macros used as needed.
Minor adjustments had to be made to the common code to work with the
LG-array macros, mostly the fixup_cmdtable() calls are now passed the
ll_entry_start and ll_entry_count instead of linker-generated symbols.
The command.c had to be adjusted as well so it would use the newly
introduced LG-array API instead of directly using linker-generated
symbols.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
This patch adds support for linker-generated array. These arrays
are a generalization of the U-Boot command declaration approach.
Basically, the idea is to generate an array, where elements of the
array are statically initialized at compile time and each element
is declared separatelly at different place. Such array is assembled
together into continuous piece of memory by linker and a pointer to
it's first entry can then be retrieved via accessor.
The actual implementation relies on placing any variable that is to
represent an element of LG-array into particular subsection of the
.u_boot_list linker section . The subsection is determined by user
options. Once compiled, it is possible to dump all symbols placed
in .u_boot_list section and the subsections in which they should be
and generate appropriate bounds for each requested subsection of the
.u_boot_list section. Each such subsection thus contains __start and
__end entries at the begining and end respecitively.
This allows for simple run-time traversing of the array, since the
symbols are properly defined.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Some of the boards still used the old PXA_MMC driver instead of the
new generic one. Use the new one instead so the old can be removed
and the generic MMC framework can be properly used.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
MMC host controller requires a delay between every sdhci_send_cmd()
execution. In s5p_mmc driver (s5p_sdhci replaces this driver), a delay
of 1000us was provided after every mmc_send_cmd() call. Adding a quirk
in current sdhci driver to replicate the behaviour.
Without this delay, MMC initialization on Origen board fails with
following error messages.
Timeout for status update!
mmc fail to send stop cmd
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Flip the boards to use the generic bounce buffer instead of the
MMC one.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Implement common bounce buffer to be used on a less capable hardware.
That includes hardware that can not do DMA from any address or such.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Andy Fleming <afleming@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
To support Non-ASCII keys (ex, Fn, PgUp/Dn, arrow keys, ...), we need to
translate key code into escape sequence.
(Updated by sjg@chromium.org to move away from a function to store
keycodes, so we can easily record how many were sent. We now need to
return this from input_send_keycodes() so we know whether keys were
generated.)
Signed-off-by: Hung-Te Lin <hungte@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
The BIOS leaves the keyboard enabled during boot time so that any
keystroke would interfere kernel driver initialization.
Add a way to disable the keyboard to make sure no scancode will be
generated during the boot time. Note that the keyboard will be
re-enabled again after the kernel driver is up.
This code can be called from the board functions.
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
On x86, the i8042 keyboard controller driver frequently waits for the keyboard
input buffer to be empty to make sure the controller has had a chance to
process the data it was given. The way the delay loop was structured, if the
controller hadn't cleared the corresponding status bit immediately, it would
wait 1ms before checking again. If the keyboard responded quickly but not
instantly, the driver would still wait a full 1ms when perhaps 1us would have
been sufficient. Because udelay is a busy wait anyway, this change decreases
the delay between checks to 1us.
Also, this change gets rid of a hardcoded 250ms delay.
On Stumpy, this saves 100-150ms during boot.
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@ti.com>
There used to be a huge structure duplicated 3 times in the source.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch provides a support to use buffered writes on flash
for versatile and vexpress boards.
This will certainly increase the flash writes.
Signed-off-by: Jagannadha Sutradharudu Teki <402jagan@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Oliver Brown <obrown@adventnetworks.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
The sbc8548/60 (both similar, just variations in UART hardware)
support has been removed from the linux kernel as of v3.6-rc1~132
so lets also now remove it from the u-boot tree as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The recent U-Boot version 2012.07 has improved drivers
(e.g. MMC and network/FEC) regarding DCache handling.
So it should be safe to use the DCache on the i.MX6, now.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This changes input_data() and friends from static function to global symbols
under weak alias, to enable board specific overrides (and therefore get rid of
board-specific code in cmd_ide.c)
Also declare ide_bus_offset in the header file, so other files can use
ATA_CURR_BASE as well.
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
move most of mpc8xx hooks from cmd_ide.c into ide_preinit() and newly created
ide_init_postreset() (invoked after calling ide_reset after ide_preinit),
some cleanup to make checkpatch happy, enable IDE init hooks in configs of
affected boards.
confusingly, these hooks are used by more than just mpc8xx-based boards, and
therefore are placed in arch/ppc/lib/
note: checkpatch still emits warnings about using volatile
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
U-Boot contains a lot of duplicit implementations of serial_puts()
call which just pipes single characters into the port in loop. Implement
function that does this behavior into common code, so others can make
easy use of it.
This function is called default_serial_puts() and it's sole purpose
is to call putc() in loop on the whole string passed to it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: James F. Dougherty <jfd@broadcom.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Since the at91sam9263, the mmc hardware support multi blocks read/write. So this driver enable it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
We define CONFIG_SYS_TEXT_BASE in board's specified header file.
So config.mk is useless, then remove it.
Signed-off-by: Zhizhou Zhang <etou.zh@gmail.com>
Adds support for HDMI, two LVDS panels and one RGB panel to
the SABRE-Lite board.
Displays supported:
HDMI - 1024 x 768 for maximum compatibility
Hannstar-XGA - 1024 x 768 LVDS (Freescale part number MCIMX-LVDS1)
wsvga-lvds - 1024 x 600 LVDS (Boundary p/n Nit6X_1024x600)
wvga-rgb - 800 x 480 RGB (Boundary p/n Nit6X_800x480)
Since the ipuv3_fb display driver currently supports only a single display,
this code auto-detects panel by probing the HDMI Phy for Hot Plug Detect
or the I2C touch controller of the LVDS and RGB displays in the priority
listed above.
Setting 'panel' environment variable to one of the names above will
override auto-detection.
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
The mmcroot setting vary between mx6qsabreauto and mx6qsabresd so we
move this to the board configuration file.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>
On mxc, each SDHC instance has a dedicated clock, so gd->sdhc_clk is not
suitable for the multi-instance use case (initialization made directly with
fsl_esdhc_initialize()).
This patch fixes this issue by adding a configuration field for the SDHC input
clock frequency.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Andy Fleming <afleming@gmail.com>
Add basic support for HP iPAQ h2200 palmtop. h2200 palmtop was targeted
to general consumers. It has 64 MB of RAM, 32 MB flash. No intergrated
Wi-Fi nor Ethernet. Based on Intel PXA255 processor. It was shipped with
Windows CE 4.2 operating system.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
sh_i2c.c support I2C0 and I2C1. This patch extends it to I2C4.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Adjust i2c_raw_read() in sh_i2c.c to work for SH73A0.
After this patch, "i2c md" and "i2c mw" command on U-Boot work properly on KZM-A9-GT board.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
R-mobile SoC (at least SH73A0) has extension bits to store 8th bit of iccl and icch.
This patch add support for the extentin bits.
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
The libfdt read/write functions are now usable enough that it's become a
moderately common pattern to use them to build and manipulate a device
tree from scratch. For example, we do so ourself in our rw_tree1 testcase,
and qemu is starting to use this model when building device trees for some
targets such as e500.
However, the read/write functions require some sort of valid tree to begin
with, so this necessitates either having a trivial canned dtb to begin with
or, more commonly, creating an empty tree using the serial-write functions
first.
This patch adds a helper function which uses the serial-write functions to
create a trivial, empty but complete and valid tree in a supplied buffer,
ready for manipulation with the read/write functions.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
From git://git.jdl.com/software/dtc.git patch hash be6026838 with
adaptations to include/libfdt.h and lib/libfdt/Makefile for the U-Boot
environment.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Allow the itb file to declare to u-boot that its hash should not be
checked automatically on bootm or iminfo. This allows an image to
either be checked automatically or to include a script which may
check it otherwise (such as after part of the itb has been relocated
to RAM by the script).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
In device trees in the world, properties consisting of a single 64-bit
integer are not as common as those consisting of a single 32-bit, cell
sized integer, but they're common enough that they're worth including
convenience functions for.
This patch adds helper wrappers of fdt_setprop_inplace(), fdt_setprop() and
fdt_appendprop() for handling 64-bit integer quantities in properties. For
better consistency with the names of these new *_u64() functions we also
add *_u32() functions as alternative names for the existing *_cell()
functions handling 32-bit integers.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Some properties may contain multiple values, these values may need
to be added to the property respectively. this patch provides this
functionality. The main purpose of fdt_append_prop() is to append
the values to a existing property, or create a new property if it
dose not exist.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Since commit 50d4a707f0 (mx5/6: Define default SoC input clock frequencies)
we can use the default clock values.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The CSI PODF bit-field used by the previous code for the i.MX31 CCM PDR0
register is actually composed of two bit-fields: one pre-divider and one
post-divider. This patch fixes the CCM access macros and the code using them
accordingly.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
The mx6qsabreauto console is different than mx6qsabresd so the console
configuration is now set in the board file.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
Define default SoC input clock frequencies for i.MX5/6 in order to get rid of
duplicated definitions.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Cc: Matt Sealey <matt@genesi-usa.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabreauto is a board based on mx6q SoC with the following features:
- 2GB of DDR3
- 2 USB ports
- 1 HDMI output port
- SPI NOR
- 2 LVDS LCD ports
- Gigabit Ethernet
- Camera
- eMMC and SD card slot
- Multichannel Audio
- CAN
- SATA
- NAND
- PCIE
- Video Input
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
mx6qsabresd has a AR8031 Gigabit PHY.
Add support for it.
Also increase CONFIG_SYS_MALLOC_LEN so that FEC buffer allocation does not fail.
Tested on 1Gbp and 100Mbps networks.
Suggested-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
mx6qsabresd is a board based on mx6q SoC with the following features:
- 1GB of DDR3
- 1 USB OTG port
- 1 HDMI output port
- SPI NOR
- LVDS panel
- Gigabit Ethernet
- Camera Connector
- eMMC and SD card slot
- Audio
Add very basic support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This is extremely likely to be used from the boot.scr that Tegra's default
bootcmd locates and executes.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Medcom is the marketing name for an older, PXA-based version of the same
device. In order to avoid confusion, rename the Tegra-based version to
the new marketing name.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
It is inconvenient to have to specify the keyboard repeat and delay at
init time if it is not yet available, so move this into a separate
function.
Some drivers will want to do this when their keyboard init routine
is actually called.
Signed-off-by: Simon Glass <sjg@chromium.org>
- block_dev_desc_t says that block_(read|write) take lbaint_t for blkcnt
not ulong.
- We also move the extern of sata_dev_desc into <sata.h>
- Remove now duplicate declarations from driver-specific headers.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Pavel Herrmann <morpheus.ibis@gmail.com>
PXA25x gadget implements common function usb_disconnect().
This patch adds this function prototype into usb.h for boards using it.
Signed-off-by: Lukasz Dalek <luk0104@gmail.com>
Allows for easy configuration of the VBUS indicator related ULPI
config bits.
Also move the external indicator setup from ulpi_set_vbus() to
the new function.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>
As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter De Schrijver <p2@mind.be>
Acked-by: Marek Vasut <marex@denx.de>
Since the IOP480 (PPC401/3 variant from PLX) is only used on 2
boards that are not actively maintained, lets remove support
for it completely. This way the ppc4xx code will get a bit cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Acked-by: Marek Vasut <marex@denx.de>
Remove the parts depending either on disabled CONFIG_SERIAL_MULTI
or ifdefs around CONFIG_SERIAL_MULTI parts since CONFIG_SERIAL_MULTI
is now enabled by default.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove any notion of CONFIG_SERIAL_MULTI from board config files.
Since CONFIG_SERIAL_MULTI is now enabled by default, it is useless
to specify this config option in the board config files. Therefore
remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Rework the emulation of serial console via JTAG from simple ad-hoc
implementation of serial port routines to CONFIG_SERIAL_MULTI and
enable CONFIG_SERIAL_MULTI unconditionally for blackfin.
In order for the JTAG serial console to take precedence over all
other serial ports available in system, implement override for
default_serial_console call returning this JTAG serial console.
This brings in a bit of a growth of size, but eventually will allow
us to unconditionally enable CONFIG_SERIAL_MULTI throughout the whole
U-Boot and maintain only one serial subsystem.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Remove the prototypes for zoom2_serial_deviceN from serial.h . This
can't be done right away, as they are referenced from the zoom2
config file. Therefore, adjust the code so the config file only
specifies number of the port. Then, replace the simple return in
default_serial_console() with a switch across possible values, which
returns the zoom2_serial_deviceN . With such adjustment in place,
the exported prototypes in serial.h can be safely removed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Rename the serial_register_bfin_uart() to bfin_initialize_serial()
to be consistent with the rest of the naming. Next, remove it's
prototype from serial.h and properly insert it into serial.c as
the rest of the serial initialization functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Remove the exports from serial.h as they are only used in the blackfin
serial driver. Furthermore, they are only used for registration, which
is handled already inside that driver and default_serial_port() call,
which is also handled in that driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Move the registration of eserialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented ns16550_serial_initialize() function, which is
implemented inside of the ns16550 serial driver allows encapsulation
of eserialN_device within the ns16550 serial driver itself.
Also, remove the exports of eserialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the ns16550 serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented mpc512x_serial_initialize() function, which is
implemented inside of the mpc512x serial driver allows encapsulation
of serialN_device within the mpc512x serial driver itself.
Also, remove the exports of serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the mpx512x serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Move the registration of xuartlite_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented xuartlite_serial_initialize() function, which is
implemented inside of the serial_xuartlite driver allows encapsulation
of xuartlite_serialN_device within the serial_xuartlite driver itself.
Also, remove the exports of xuartlite_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_xuartlite driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of zynq_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented zynq_serial_initialize() function, which is
implemented inside of the serial_zynq driver allows encapsulation
of zynq_serialN_device within the serial_zynq driver itself.
Also, remove the exports of zynq_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_zynq driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Tom Rini <trini@ti.com>
Move the registration of s5p_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s5p_serial_initialize() function, which is
implemented inside of the serial_s5p driver allows encapsulation
of s5p_serialN_device within the serial_s5p driver itself.
Also, remove the exports of s5p_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s5p driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Move the registration of serial_XXuart ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented pxa_serial_initialize() function, which is
implemented inside of the serial_pxa driver allows encapsulation
of serial_XXuart within the serial_pxa driver itself.
Also, remove the exports of serial_XXuart from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_pxa driver and
the default console is picked by CONFIG_CONS_IDX macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the registration of s3c24xx_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s3c24xx_serial_initialize() function, which is
implemented inside of the serial_s3c24xx driver allows encapsulation
of s3c24xx_serialN_device within the serial_s3c24xx driver itself.
Also, remove the exports of s3c24xx_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s3c24xx driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: C Nauman <cnauman@diagraph.com>
Some of the boards using the mpc512x serial driver didn't properly
define which PSC console to use. This caused breakage when building
with CONFIG_SERIAL_MULTI enabled. Fix this by defining the default
PSC console.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Make use of the newly implemented weak default_serial_console in
the serial_pxa driver. This removes all reimplementations of this
function from board files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Rename .init() to .start() and .uninit() to .stop() in struct
serial_device. This allows aligning struct serial_device with
closer to struct stdio_dev. The real goal here is to allow
these two structures to converge together and eventually make
one to be a superset of the other.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Do a simple cleanup of the struct serial_device and align it with
current coding style. Checkpatch now reports no errors.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Kill multiple occurances and redeclaration of MK_STR
in favor of __stringify().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Kill multiple occurances and redeclaration of xstr in favor of __stringify().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Copied from Linux kernel:
commit 8f7c2c37319a81ef4c2bfdec67b1ccd5744d97e4
Date: Wed Apr 8 16:58:57 2009 +0800
Pull in the __stringify() macro from Linux kernel. This macro is usually used to
convert numbers to strings at preprocessor level, yet it is not limited only to
that. This is useful as it allows higher usage of puts() in favour of printf().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The SPI flash is not properly detected by plain "sf probe" due to
it being located on different bus and different chipselect. Fix
this problem.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
The IDE_BUS(dev) macro was previously doing dev >> 1. This however is a
mis-match of the usage in common/cmd_ide.c and would cause boards with
multiple ports / devices to not correctly detect all devices. For more
details please see:
http://lists.denx.de/pipermail/u-boot/2012-April/122525.html
[Tom Rini: Reword commit message only]
Tested-by: Luka Perkov <uboot@lukaperkov.net>
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
The default configuration for ml507 will generate a hang() in the
Xilinx uartlite driver.
userial_ports[] in drivers/serial/serial_xuartlite.c does not get
initialized properly. CONFIG_SERIAL_BASE is unused.
XILINX_UARTLITE_BASEADDR is used instead.
Signed-off-by: Rommel Custodio <sessyargc+uboot@gmail.com>
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Add minimal support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Chin Liang See <clsee@altera.com>
Signed-off-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Tom Trini <trini@ti.com>
Cc: Wolfgang Denx <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefan Roese <sr@denx.de>
----
v8: Remove no_return attribute for reset_cpu
Based on v2012.10-rc2
Add support for Xilinx Zynq board.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
CC: Joe Hershberger <joe.hershberger@gmail.com>
The driver is used on Xilinx Zynq platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds support for the X600 SPEAr600 based board. Its also
the first SPEAr600 board that uses the newly introduced SPEAr600
SPL support. Xloader is not necessary any more. By using the new
"u-boot.spr" make target, one image will generated containing both,
U-Boot SPL (with mkimage header as needed by the SPEAr BootROM, and
the main U-Boot with mkimage header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
On x86 machines gd is unfortunately a #define, so we should avoid using
gd for anything. This patch changes uses of gd to bgd so that ext4fs
can be used on x86.
A better fix would be to remove the #define in x86, but I'm not sure
how to do that.
Signed-off-by: Simon Glass <sjg@chromium.org>
Malloc len of 128K caused a warning from
ehci_hcd asking for more.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
This patch adds support for the LaCie board d2 Network v2 which share
a lot of hardware caracteristics with the 2Big Network v2.
- CPU: Marvell 88F6281 1200Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- 2 SATA ports: internal and eSATA
- Gigabit ethernet: PHY Marvell 88E1116R
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports: host and host/device
- 1 push button
- 1 power switch
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
This patch adds support for the LaCie boards Network Space v2 (Lite and
Mini). This two boards are derived from the Network Space v2 and a lot
of hardware caracteristics are shared.
- CPU: Marvell 88F6192 800Mhz
- SDRAM memory: 128MB DDR2 200Mhz
- 1 SATA port: internal
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: SPI NOR 512KB (Macronix MX25L4005A)
- i2c EEPROM: 512 bytes (24C04 type)
- 2 USB2 ports (Lite only): host and host/device
- 1 push button
- 1 SATA LED (bi-color, blue and red)
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Defines CONFIG_EFI_PARTITION for LaCie boards.
Additionally this patch defines CONFIG_DOS_PARTITION. Note that this
definition is implicit in mv_common.h when CONFIG_CMD_USB is enabled.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Support of the MINI2440 board from FriendlyARM from
an old version of u-boot :
http://repo.or.cz/r/u-boot-openmoko/mini2440.git
Currently, supporting only boot from NOR.
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
kzm9g board use global timer. But by commit 813ffda31, timer function of
rmobile was changed that global timer might be used, when CONFIG_GLOBAL_TIMER
was defined.
This add CONFIG_GLOBAL_TIMER to board config file.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some rmobile SoC has TMU base timer function. This supports TMU.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove CONFIG_INTEGRATOR and CONFIG_ARCH_CINTEGRATOR. These are not for kzm9g.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The value of CONFIG_BAUDRATE is treated as string and put as initial value of
environment variable. If it begin with '(', it is wrongly parsed to 0 in number.
So I removed '(' and ')'.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reserve first 16MB for RT-CPU (as same as kernel config).
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The KZM-A9-GT board has Renesas R-Mobile SH73A0, 512MB DDR2-SDRAM,
USB, Ethernet, and more.
This patch supports the following functions:
- 512MB DDR2-SDRAM
- 16MB NOR Flash memory
- Serial console (SCIF)
- Ethernet (SMSC)
- I2C
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is useful to be able to write the bootstage information to memory for
use by a later utility, or the Linux kernel. Provide a function to do
this as well as a function to read bootstage information back and incorporate
it into the current table.
This also makes it possible for U-Boot to chain to another U-Boot and pass
on its bootstage information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an option, CONFIG_BOOTSTAGE_FDT to pass boot timings to the kernel
in the device tree, if available. To use this, you must have
CONFIG_OF_LIBFDT defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we want to add up the amount of time spent in a particular
activity when it is happening in a number of discrete chunks.
Add bootstage_start() to mark the start of an acitivity and
bootstage_accum() to accumulate the time since the last start. Calling
these function in pairs results in the accumulated time being collected.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is not static, but not exported either. Add a prototype
in the header file and move the required enum to the header also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since a while, the size of the u-boot.bin image is larger than
256kB. This requires moving the environment sectors by one. As
we are at it, we also update a few other custom settings.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
A fast boot is important to the beaglebone, so save 2 seconds here by
decreasing bootdelay. This is still plenty time to break into the prompt,
I do that at least once a day.
Mount the rootfs RO by default, this is needed to make fsck succeed
without resorting to an initramfs.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
This patch adds support for networking in SPL. Some devices are
capable of loading SPL via network so it makes sense to load the
main U-Boot binary via network too. This patch tries to use
existing network code as much as possible. Unfortunately, it depends
on environment which in turn depends on other code so SPL size
is increased significantly. No effort was done to decouple network
code and environment so far.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for networking in SPL on TI AM335x based
boards. Vendor Class Identifier used by SPL during BOOTP is
"AM335x U-Boot SPL".
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>