Commit Graph

5221 Commits

Author SHA1 Message Date
Tom Rini
44fb0d6c9f Xilinx/FPGA changes for v2020.01
FPGA:
 - Enable fpga loading on Versal
 - Minor fix
 
 Microblaze:
 - Fix LMB configurations to support initrds
 - Some other cleanups
 
 Zynq:
 - Minor config/dt changes
 - Add distro boot support for usb1 and mmc1
 - Remove Xilinx private boot commands and use only distro boot
 
 ZynqMP:
 - Kconfig cleanups, defconfig updates
 - Update some dt files
 - Add firmware driver for talking to PMUFW
 - Extend distro boot support for jtag
 - Add new IDs
 - Add system controller configurations
 - Convert code to talk firmware via mailbox or SMCs
 
 Versal:
 - Add board_late_init()
 - Add run time DT memory setup
 - Add DFU support
 - Extend distro boot support for jtag and dfu
 - Add clock driver
 - Tune mini configurations
 
 Xilinx:
 - Improve documentation (boot scripts, dt binding)
 - Enable run time initrd_high calculation
 - Define default SYS_PROMPT
 - Add zynq/zynqmp virtual defconfig
 
 Drivers:
 - Add Xilinx mailbox driver for talking to firmware
 - Clean zynq_gem for Versal
 - Move ZYNQ_HISPD_BROKEN to Kconfig
 - Wire genphy_init() in phy.c
 - Add Xilinx gii2rgmii bridge
 - Cleanup zynq_sdhci
 - dwc3 fix
 - zynq_gpio fix
 - axi_emac fix
 
 Others:
 - apalis-tk1 - clean config file
 -----BEGIN PGP SIGNATURE-----
 
 iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXZ2mcwAKCRDKSWXLKUoM
 IT/KAJ4tL49YwINqCVGd7gafWvdfC4htygCcCgr9gLnJ+LjDQkxWT/r6faIcL00=
 =OnMk
 -----END PGP SIGNATURE-----

Merge tag 'xilinx-for-v2020.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze

Xilinx/FPGA changes for v2020.01

FPGA:
- Enable fpga loading on Versal
- Minor fix

Microblaze:
- Fix LMB configurations to support initrds
- Some other cleanups

Zynq:
- Minor config/dt changes
- Add distro boot support for usb1 and mmc1
- Remove Xilinx private boot commands and use only distro boot

ZynqMP:
- Kconfig cleanups, defconfig updates
- Update some dt files
- Add firmware driver for talking to PMUFW
- Extend distro boot support for jtag
- Add new IDs
- Add system controller configurations
- Convert code to talk firmware via mailbox or SMCs

Versal:
- Add board_late_init()
- Add run time DT memory setup
- Add DFU support
- Extend distro boot support for jtag and dfu
- Add clock driver
- Tune mini configurations

Xilinx:
- Improve documentation (boot scripts, dt binding)
- Enable run time initrd_high calculation
- Define default SYS_PROMPT
- Add zynq/zynqmp virtual defconfig

Drivers:
- Add Xilinx mailbox driver for talking to firmware
- Clean zynq_gem for Versal
- Move ZYNQ_HISPD_BROKEN to Kconfig
- Wire genphy_init() in phy.c
- Add Xilinx gii2rgmii bridge
- Cleanup zynq_sdhci
- dwc3 fix
- zynq_gpio fix
- axi_emac fix

Others:
- apalis-tk1 - clean config file
2019-10-09 16:22:03 -04:00
Tom Rini
eaa0bde051 u-boot-imx-20191009
-------------------
 
 Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532
 
 - MX6UL / ULZ
 - Toradex board
 - Allow to set OCRAM for MX6Q/D
 - MX7ULP
 - MX8: (container image, imx8mq_mek), SCU API
 - fix several board booting from SD/EMMC (cubox-i for example)
 - pico boards
 -----BEGIN PGP SIGNATURE-----
 
 iQHDBAABCgAtFiEEiZClFGvhzbUNsmAvKMTY0yrV63cFAl2dlTAPHHNiYWJpY0Bk
 ZW54LmRlAAoJECjE2NMq1et3yfgL/1b4pKCwxswK42XkPpdHN1u/v2W/PVDanl/H
 EYxlluHVFH23bLTjLvrrgQjAnZD1VQhxWq3bwCMoJ8vb9tYQ3d9vq7XADQ0WVQV+
 EfhE33fVRPRT3rEdhDKWm+y1mL8YPvYEBnr9li7qU9n1VxiwONPXxMXMqoo9/lbM
 b6lJaG5KkuK8Ofx3cYFVQeAEdsFYIJ2aXtTqsqrV9o2sjruOuG3Ux+6Ov+9O0crY
 q8MXvW6kwWkVVNriVV7Yal0pomPZfMTqft007En9Mv2FtXqMeCWZ4Xh2LtRylR7n
 ruIbo94jkPuwuZ0p/6SeiyopoG/hU/skrkJv1s8W70DOsyaunP2BsveYXEjMV2Rb
 DomotcJit9Ws6P7rOP1oI8OvxSxVN8n6mo23UviZd8MjNAmOm49BtSxVGGB+pwmr
 ufGFG4MGQ5VpCxmzh6KrJCLXpI/mhKrkBkZy58cUbus7aPv3es/jBmmtGlU3m6ka
 NlEzHOX1hpJV/lhLvxjqRhVxuXvXOA==
 =+e3p
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20191009' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20191009
-------------------

Travis : https://travis-ci.org/sbabic/u-boot-imx/builds/595148532

- MX6UL / ULZ
- Toradex board
- Allow to set OCRAM for MX6Q/D
- MX7ULP
- MX8: (container image, imx8mq_mek), SCU API
- fix several board booting from SD/EMMC (cubox-i for example)
- pico boards

[trini: display5 merged manually]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-10-09 11:44:45 -04:00
Tom Rini
8c05abad13 Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- Move WATCHDOG_TIMEOUT_MSECS to Kconfig (Heiko)
2019-10-08 18:45:49 -04:00
Tom Rini
efea5a34bb Merge https://gitlab.denx.de/u-boot/custodians/u-boot-x86
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
2019-10-08 18:45:26 -04:00
Heinrich Schuchardt
86d2b28b28 configs: sheevaplug disable EFI_UNICODE_CAPITALIZATION
With upcoming patches u-boot.kwb gets too large.

Save 3740 bytes in u-boot.kwb by disabling Unicode support in the UEFI
sub-system.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2019-10-08 16:36:37 +02:00
Joris Offouga
f730fdf98b pico-imx7d: fix splash logo drawing
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:36:37 +02:00
Stefano Babic
d714a75fd4 imx: replace CONFIG_SECURE_BOOT with CONFIG_IMX_HAB
CONFIG_SECURE_BOOT is too generic and forbids to use it for cross
architecture purposes. If Secure Boot is required for imx, this means to
enable and use the HAB processor in the soc.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2019-10-08 16:36:37 +02:00
Parthiban Nallathambi
39fd054fee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
CONFIG_SPL_TEXT_BASE is moved to common/spl/Kconfig, update
pcl063_ull defconfig.

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
2019-10-08 16:36:37 +02:00
Saravanan Sekar
a7031d9f54 imx: variscite: Fix regression of SPL and U-boot booting
1. Commit 3a7c45f6a7 ("simple-bus: add DM_FLAG_PRE_RELOC flag to
simple-bus driver") causes some i.MX boards that were converted
to DM, such as warp7, to fail to boot.

As explained by Lukas Auer:

"With the patch, U-Boot probes the drivers for devices under simple-bus
device tree nodes in the pre-relocation device model. The default value
of CONFIG_SYS_MALLOC_F_LEN (0x4000) leaves U-Boot with not enough memory to
do this, causing it to hang."

Fix this problem by providing a convenient default value for
CONFIG_SYS_MALLOC_F_LEN.

2. CONFIG_SPL_TEXT_BASE was moved to Kconfig, so added in defconfig
"configs: move CONFIG_SPL_TEXT_BASE to Kconfig"
(sha1: f89d6133ee)

Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:37 +02:00
Adam Ford
7cf388fa69 ARM: imx6q_logic: Enable DM_SERIAL
In order to call preloader_console_init from board_init_f when
DM_SERIAL is enabled, it neesd to call spl_early_init() to get early access
to DM and device tree.

This patch calls spl_early_init just before preloader_console_init()
and enables DM_SERIAL and SPL_DM_SERIAL.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08 16:36:37 +02:00
Parthiban Nallathambi
a919b6ba37 imx: pcl063: add nand boot support
Booting from NAND needs nandbcb and nand boot device selection

Signed-off-by: Parthiban Nallathambi <pn@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:37 +02:00
Peng Fan
9b15ce9193 imx: Add i.MX8MM EVK board support.
Add board and SoC dts
Add ddr training code
support SD/MMC/GPIO/PINCTRL/UART

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:36 +02:00
Anatolij Gustschin
0a1a45b7d6 imx: mx6ul_14x14_evk: fix link issue
Since recent splash changes common code for splashscreen logo
should be used instead of adding duplicated code under board
directories. mx6ul_9x9_evk and mx6ul_14x14_evk configurations
used old board specific logo code and do not link, fix them.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:36:36 +02:00
Patrick Wildt
2845f86d95 imx: enable the reset controller on the i.MX8MQ EVK
This patch makes sure that the reset controller driver is compiled
for the i.MX8MQ EVK.

Signed-off-by: Patrick Wildt <patrick@blueri.se>
2019-10-08 16:36:36 +02:00
Patrick Wildt
d08a194871 imx: add support for i.MX8MQ power domain controller
Add support for the power domain controller that's used on the
i.MX8MQ.  This will be needed to be able to power on the PCIe
controller.  Bindings taken from Linux, driver implementation
taken from the i.MX8 power domain controller and adjusted for
the i.MX8M SoC.

Signed-off-by: Patrick Wildt <patrick@blueri.se>
2019-10-08 16:36:36 +02:00
Anatolij Gustschin
e4b91f085d imx: wandboard: convert FEC support to DM_ETH
Remove CONFIG_DM_ETH conversion warning to avoid board removal.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08 16:36:36 +02:00
Lukasz Majewski
5ec7d1b495 ARM: Update display5_factory_defconfig after switch to DM/DTS and uuu utility
This commit updates the display5_factory_defconfig file after the switch
to DM/DTS for this board.

Moreover, the VID and PID for SPL running SDP gadget have been updated to
allow seamless work with 'uuu' utility from NXP (the imx_usb doesn't work
properly after embedding the u-boot proper into fitImage - problem with IVT
embedding in FIT).

Example to use 'uuu' session:

cat << EOF > display5_recovery.lst
uuu_version 1.2.135
SDP: boot -f /srv/tftp/SPL
SDPU: write -f /srv/tftp/u-boot-dtb.img -addr 0x10000000
SDPU: jump -addr 0x10000000
SDPU: done
EOF

sudo ./uuu/uuu display5_recovery.lst

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:36:35 +02:00
Lukasz Majewski
d5354f59d0 DM: WDT: Convert WDT driver to use DM/DTS (including SYSRESET)
This commit enables support for CONFIG_WDT in the U-Boot proper. Moreover,
the SYSRESET_WATCHDOG driver is used to support 'reset' command.

As SPL is not yet ready for DM conversion, the CONFIG_HW_WATCHDOG is
enabled for it. This allows the legacy SPL code to work properly.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:35:59 +02:00
Lukasz Majewski
e95b4bdd8d DM: SPI: Convert display5 to use SPI with DM/DTS (but no in SPL)
The DM/DTS support for SPI is disabled on purpose for SPL, as it is not
supported as of time of this conversion.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:35:59 +02:00
Lukasz Majewski
1b20e3a281 ARM: imx: defconfig: Enable 'regulator' and 'pmic' commands on display5
Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:35:59 +02:00
Lukasz Majewski
dac9a8f8a2 DM: I2C: Switch display5 board to use DM_I2C
After this commit the display5 device would use I2C driver supporting
driver model (DM_I2C).

The 'i2c' and 'eeprom' commands now use DM I2C drivers and initialize
on-bus devices according to device tree description.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:35:59 +02:00
Lukasz Majewski
5ca7094668 ARM: imx: defconfig: Enable CONFIG_PINCTRL{_IMX6} on display5's defconfig
Enable PINCTRL for i.MX6 soc based display5 after DM/DTS conversion.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:35:59 +02:00
Lukasz Majewski
4c3c29e3b0 fix: defconfig: Enable OF_CONTROL for display5_factory
This change fixes issue with building display5 "factory" U-Boot variant
when the display5 board gains DM/DTS support.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
2019-10-08 16:35:59 +02:00
Fabio Estevam
953c2500bc pico-imx6: Add splashscreen support
Add splashscreen support. Tested with the parallel
FT5x06-WVGA panel.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Otavio Salvador
7efe52a0a7 pico-imx6: Fix bootmenu handling
We should use a common script to allow booting the U-Boot console as
fallback so we ended using a 'default_boot' and 'base_boot'
environment scripts to accomplish that.

Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Fabio Estevam
004eee86f1 pico-imx6: Add initial support
Add the initial support for the pico-imx6 variants.

DDR initialization is based on the TechNexion's U-Boot code.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Stefano Babic
31bd001b21 board: imx6dl_mamoj: set the value for CSF size
Default value is too high and it covers the worst case. SPL for
imx6dl_mamoj becomes too big and cannot fit into the OCRAM, but CSF size
can be reduced.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Breno Lima <breno.lima@nxp.com>
2019-10-08 16:35:59 +02:00
Otavio Salvador
9b1fd3c834 configs: Sync all baseboard specific pico-imx7d
This syncs all baseboard specific defconfig using the
pico-imx7d_defconfig as base. It changes:

 - pico-dwarf-imx7d_defconfig
 - pico-hobbit-imx7d_defconfig
 - pico-nymph-imx7d_defconfig
 - pico-pi-imx7d_defconfig

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Joris Offouga
d89f0a889f configs: pico-imx7d: Convert to DM_VIDEO
This commit convert all pico-imx7d to DM_VIDEO

Signed-off-by: Joris Offouga <offougajoris@gmail.com>
2019-10-08 16:35:59 +02:00
Anatolij Gustschin
4289912715 imx: sksimx6_defconfig: remove SPL misc option to fix build error
Remove CONFIG_SPL_DRIVERS_MISC_SUPPORT since it is already defined
in include/configs/mx6_common.h for SPL builds. When this option
is in defconfig, we get build warnings (or errors when building
with -Werror).

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2019-10-08 16:35:59 +02:00
Fabio Estevam
b31bed279a pico: Convert to CONFIG_FSL_USDHC
The eSDHC config symbol has been converted to CONFIG_FSL_USDHC, so
adjust it accordingly in order to fix the build errors:

https://travis-ci.org/sbabic/u-boot-imx/jobs/584781580#L1287

Reported-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
2019-10-08 16:35:59 +02:00
Otavio Salvador
34ac994245 pico-imx7d: Add NYMPH baseboard support
This add the boot menu option for the NYMPH baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Otavio Salvador
e82e292751 pico-imx7d: Add DWARF baseboard support
This add the boot menu option for the DWARF baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Fabio Berton
cca5c03644 pico-imx7d: Sync pico-hobbit-imx7d_defconfig
Update pico-hobbit-imx7d_defconfig using pico-imx7d_defconfig as base
to fix device tree file generation. With this all pico-imx7d are
creating u-boot-dtb.img files.

Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Fabio Estevam
5d1ed3024a pico-imx6ul: Add LCD support
Add support for the VXT VL050-8048NT-C01 panel connected through
the 24 bit parallel LCDIF interface.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Otavio Salvador
9988001089 pico-imx6ul: Add DWARF baseboard support
This add the boot menu option for the DWARF baseboard as well as a
specific config file for users which wish to use it as a pre-defined
board.

Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
2019-10-08 16:35:59 +02:00
Peng Fan
6e92cae3cd configs: imx8qm/qxp_mek: enable CONFIG_OF_SYSTEM_SETUP
Enable CONFIG_OF_SYSTEM_SETUP to let U-Boot could disable
device tree nodes that could not be used by Linux.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:59 +02:00
Peng Fan
f31f8b0434 imx8qm_mek: switch to use container image
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.

Enable HUSH_PARSER in defconfig to make run netboot could work.

Note: The AHAB related code has not been added.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:58 +02:00
Peng Fan
d94049ce19 imx8qxp_mek: switch to use container image
Because FIT could not be used for AHAB secure boot on i.MX8,
so switch to use container image that could let SPL verify
ATF and U-Boot with AHAB.

Note: The AHAB related code has not been added.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:58 +02:00
Peng Fan
ebf4f0944d imx: mx6sabresd: fix usb start when DM enabled
Enable CONFIG_DM_REGULATOR_FIXED to let vbus regulator work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:58 +02:00
Breno Matheus Lima
5f2fe3b93a Kconfig: Migrate CONFIG_CSF_SIZE to Kconfig
Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.

mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2019-10-08 16:35:58 +02:00
Fabio Estevam
91457597e3 mx6sabresd: Reduce overall SPL size
Currently the SPL binary is 67 kB, which leaves only 1 kB of free
internal RAM space.

The following options can be safely removed to save some precious
SPL space:

- CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd
command (at offset 69 kB)
- CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL
- CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported
by default

After this change the SPL binary size gets down to 51 kB.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:16 +02:00
Peng Fan
3399a2e1d2 i.MX7ULP: evk: Enable fuse comamnd
Enable fuse command

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:16 +02:00
Ye Li
61bf6173cd i.MX7ULP: Fix wrong i2c configuration name
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:16 +02:00
Peng Fan
bd1cc6ae6f i.MX7ULP: evk: Modify FDT file to disable SD3.0 for usb boot
Since the SD3.0 kernel driver needs M4 image support, this causes
problem for usb boot booting into kernel.  To decouple the relationship,
we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:16 +02:00
Troy Kisky
b1f955cb4d configs: nitrogen6x: Add DM_SPI/DM_SPI_FLASH support
Add CONFIG_DM_SPI/CONFIG_DM_SPI_FLASH to all defconfigs whose board is
    nitrogen6x.

    mx6qsabrelite_defconfig
    nitrogen6dl2g_defconfig
    nitrogen6dl_defconfig
    nitrogen6q2g_defconfig
    nitrogen6q_defconfig
    nitrogen6s1g_defconfig

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08 16:35:16 +02:00
Troy Kisky
684efe2f48 configs: nitrogen6x: Add DM_GPIO support
Add CONFIG_DM_GPIO to all defconfigs whose board is
nitrogen6x.

mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig

This is in preparation for adding CONFIG_DM_SPI.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08 16:35:16 +02:00
Troy Kisky
cdcaee9518 configs: nitrogen6x: Add DM_MMC/DM_USB/AHCI support
Add DM_MMC to all defconfigs whose board is
nitrogen6x.

mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig

This commit is adding multiple configs, but
seems to be the minimum change to not lose features
and still compile fine.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08 16:35:16 +02:00
Troy Kisky
f8f9f79a63 nitrogen6x: migrate to using device tree
Migrate to using device tree required for further driver model
integration.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2019-10-08 16:35:16 +02:00
Peng Fan
bdcac95565 imx: mx6slevk: enable DM_SPI and DM_SPI_FLASH
With DM_SPI and DM_SPI_FLASH enabled, we could get:

spi          0  [   ]   mxc_spi               |   |   |   `-- ecspi@02008000
spi_flash    0  [   ]   spi_flash_std         |   |   |       `-- m25p80@0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-10-08 16:35:16 +02:00