Remove LS102XA immap header inclusion from xhci fsl driver.
It removes redefinition warnings when built for platforms
other than LS102XA
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
This adjusts (micro)frame length to appropriate value thus
avoiding USB devices to time out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Support driver model in this driver. This uses the normal USB driver search
mechanism. Any EHCI controllers will be set up as they are found during
usb_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
On some single port (otg) controllers there is no emulated root hub, so
the first child (if any) may be one of: UCLASS_MASS_STORAGE,
UCLASS_USB_DEV_GENERIC or UCLASS_USB_HUB.
All three of these (and in the future others) are suitable for our
purposes, remove the check for the device being a hub, and add a check to
deal with the fact that there may be no child-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Allow usb uclass host drivers to implement usb_reset_root_port, this is
used by single port usb hosts which do not emulate a hub, such as otg
controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we unbind usb devices from usb_stop() usb_find_child() is
only necessary to deal with emulated usb devices.
Rename it to make this clear and add a #ifdef to make it a nop in
other cases.
Note the #ifdef turns usb_find_emul_child() into a nop, rather then not
building it and adding another #ifdef to the caller, this is done this way
because adding a #ifdef to the caller is somewhat hairy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
On an usb stop instead of leaving orphan usb devices behind simply remove
them.
The result of this commit is best seen in the output of "dm tree" after
plugging out an usb hub with 2 devices plugges in and plugging in a keyb.
instead, before this commit the output would be:
usb [ + ] `-- sunxi-musb
usb_hub [ ] |-- usb_hub
usb_mass_st [ ] | |-- usb_mass_storage
usb_dev_gen [ ] | `-- generic_bus_0_dev_3
usb_dev_gen [ + ] `-- generic_bus_0_dev_1
Notice the non active usb_hub child and its 2 non active children. The
first child being non-active as in this example also causes usb_get_dev_index
to return NULL when probing the first child, which results in the usb kbd
code not binding to the keyboard.
With this commit in place the output after swapping and "usb reset" is:
usb [ + ] `-- sunxi-musb
usb_dev_gen [ + ] `-- generic_bus_0_dev_1
As expected, and usb_get_dev_index works properly and the keyboard works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add an usb_device parameter to usb_reset_root_port so that it knows which
root-port it is resetting. This is necessary for proper device-model support
for usb_reset_root_port.
Also remove a duplicate declaration of usb_reset_root_port() from usb.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop the unneeded portnr function argument, the portnr is part of the
usb_device struct which is passed via the dev argument.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The device-model usb_legacy_port_reset function calls the device-model
usb_port_reset function which is a 1 on 1 copy of the non dm
usb_legacy_port_reset and this is the only use of usb_port_reset in all
of u-boot.
Drop both, and alway use the usb_legacy_port_reset() version in
common/usb.c .
Also while at it make it static as it is only used in common/usb.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.
But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a weak function board_ehci_hcd_init which can be used by the board
file for board specific initialisation.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Return if USB_MAX_CONTROLLER_COUNT hence the index of the controller
to be initialised is incorrect
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.
Update the SoC select menu in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>. Follow this trend.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has been tested to the extent that I can enumerate
a asix usb networking adapter and boot a kernel over usb
on the 96boards hikey u-boot port I'm currently doing.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Add support for interrupt queues to the ohci hcd code, bringing it inline
with the ehci and musb-new(host) code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add an ohci_alloc_urb() function, this is a preparation patch for adding
interrupt queue support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When submitting interrupt packets to an endpoint we only link in the ed
once to avoid some races surrounding unlinking of periodic endpoints,
but we share one ohci_device struct / one set of ed-s for all devices,
which means that if we have an interrupt endpoint at endpoint 1 with one
device, and a non interrupt endpoint 1 with another device we end up
with the same ed linked into both the periodic and async lists, which is
not good (tm).
This commit switches over to using separate ohci_device structs, and thus
separate ed-s for devices with interrupt endpoints, fixing this.
This fixes e.g. matching a usb storage device and keyboard on the same
usb-1 hub not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Convert sunxi-boards which use the sunxi-ehci code to the driver-model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
For some reason the ohci code is full with:
#ifdef DEBUG
pkt_print(...)
#else
mdelay(1);
#endif
AFAICT there is no reason for the mdelay(1) calls. This commit disables them
when building the ohci code for new driver-model using boards. It leaves
the mdelay(1) calls in place when building for older boards, so as to avoid
causing any regressions there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb spec says that we must wait a minimum amount of time after port
power on (exact time is in the hub descriptor), this is something which
we must not only do for root ports but also for external hub ports, which
is why the common usb_hub code already waits a full second after powering
up ports. Having a separate wait for just the root hub in the ohci-hcd
code only leads to doing the waiting twice for the root ports, so drop the
wait from the ohci-hcd code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The u-boot usb code uses polling for all endpoints, including interrupt
endpoints, so urbs should never be automatically resubmitted.
This also fixes a leak of the urb, as submit_int_msg() did not check if
an already re-submitted urb exists before creating a new one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
USB scanning is slow, and there is no need to scan the companion buses
if no usb devices where handed over to the companinon controllers by any
of the main controllers.
This saves e.g. 2 seconds when booting a A10 OLinuxIno Lime with no USB-1
devices plugged into the root usb ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB companion controllers must be scanned after the main controller has
been scanned, so that any devices which the main controller which to hand
over to the companion have actually been handed over before we scan the
companion.
As there are no guarantees that this will magically happen in the right
order, split the scanning of the buses in 2 phases, first main controllers,
and then companion controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move printing of usb scan status to usb_scan_bus().
This is a preparation patch for adding companion controller support to the
usb uclass.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Interrupt endpoints typically are polled for a long time by the usb
controller before they return anything, so calls to submit_int_msg() can
take a long time to complete this.
To avoid this the u-boot code has the an interrupt queue mechanism / API,
add support for this to the driver-model usb code and implement it for the
dm ehci code.
See the added doc comments for more details.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a preparation patch for adding interrupt-queue support to the
ehci dm code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Short circuit the retry loop in legacy_hub_port_reset() by returning an
error from usb_control_msg() when a device was handed over to a companion
by the ehci code. This avoids trying to reset low / fullspeed devices 5
times needlessly. Also do not print an error when a device has been handed
over.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When after a reset the port status connection bit is still set and the enable
bit is not then we're dealing with a full-speed device and should hand it over
to the companion controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Interrupts transfers timing out is normal, so do not log an error for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Add proper cache flushing / invalidating for non cache coherent cpus, for now
only enable this for new (driver-model) usb code to avoid regressions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Non static function and variable declarations do not belong in a .h file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
This is a preparation patch for adding driver-model support.
Note we do keep ohci_dev as a separate struct so that we can later add
support for interrupt-queues which requires allocating a separate ohci_dev
per interrupt-queue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
devgone is never assigned a value, so the one comparisson reading it will
never be true, and devgone can be completely removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Without this usb-1 device descriptors do not get read properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The ehci driver model code for finding the first upstream usb-2 hub before
this commit has a number of issues:
1) "if (!ttdev->speed != USB_SPEED_HIGH)" does not work because the '!'
takes presedence over the '!=' this should simply be
"if (ttdev->speed == USB_SPEED_HIGH)"
2) It makes ttdev point to the first upstream usb-2 hub, but ttdev should
point to the last usb-1 device before the first usb-2 hub (when going
upstream from the device), as ttdev is used to find the port of the
first usb-2 hub to which the the last usb-1 device is connected.
3) parent_devnum however should be set to the devnum of the first usb-2
hub, so we need to keep pointers around to both usb_device structs.
To complicate things further during enumeration usb_device.dev will point
to the parent udevice, where as during normal use it will point to
the actual udevice, we must handle both cases correctly.
This commit fixes all this making usb-1 devices attached to usb-2 hubs,
including usb-1 devices attached to usb-1 hubs attached to usb-2 hubs, work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use usb_get_bus in dm ehci code rather then re-implementing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently we copy over a number of usb_device values stored in the on stack
struct usb_device probed in usb_scan_device() to the final driver-model managed
struct usb_device in usb_child_pre_probe() through usb_device_platdata, and
then call usb_select_config() to fill in the rest.
There are 3 problems with this approach:
1) It does not fill in enough fields before calling usb_select_config(),
specifically it does not fill in ep0's maxpacketsize causing a div by zero
exception in the ehci driver.
2) It unnecessarily redoes a number of usb requests making usb probing slower
3) Calling usb_select_config() a second time fails on some usb-1 devices
plugged into usb-2 hubs, causing u-boot to not recognize these devices.
This commit fixes these issues by removing (*) the usb_select_config() call
from usb_child_pre_probe(), and instead of copying over things field by field
through usb_device_platdata, store a pointer to the in stack usb_device
(which is still valid when usb_child_pre_probe() gets called) and copy
over the entire struct.
*) Except for devices which are explictly instantiated through device-tree
rather then discovered through usb_scan_device() such as emulated usb devices
in the sandbox.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make usb_get_bus easier to use for callers, by directly returning the bus
rather then returning it via a pass-by-ref argument.
This also removes the error checking from the current callers, as
we already have an assert() for bus not being NULL in usb_get_bus().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Do not use bus->seq before device_probe(bus), as bus->seq is not set until
after the device_probe() call. This fixes u-boot printing: "USB-1: " for
each bus it scans.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.
Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.
Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.
This patch purely renames things, it contains no functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.
This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.
This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add driver model support in the XHCI support code so that it can be used by
XHCI USB drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Since driver model will want to use most of the same code for XHCI init
and uninit, put it in a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Rather than getting this directly from struct usb_device, call a function
to obtain it. This will make it possible for driver model to provide it
another way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We want to use mostly the same init and uninit code for driver model, so move
the common part into two functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Try to return useful error numbers where possible. Also avoid swallowing
an error number when it is returned by a called function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This variable is a bit of a hack. We can obtain the same information from
the normal device config. This will fit better with driver model, where
global variables are best avoided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This driver supports using emulation devices to provide a USB bus within
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These devices must have their addresses removed ready for the next USB
bus enumeration. Add this logic to usb_stop().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some controllers support OTG (on-the-go) where they can operate as either
host or device. The gadget layer in U-Boot supports this.
While this layer does not interact with driver model, we can provide a
function which sets up the controller in the correct way. This way the code
at least builds (although it likely will not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present USB devices with no driver model driver cannot be seen in the
device list, and we fail to set them up correctly. This means they cannot
be used.
While having real drivers that support driver model for all USB devices
is the eventual goal, we are not there yet.
As a stop-gap, add a generic USB driver which is bound when we do not have
a real driver. This allows the device to be set up and shown on the bus.
It also allows ad-hoc code (such as usb_ether) to find these devices and
set them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
USB devices in U-Boot are currently probed only after all devices have
been enumerated. Each type of device is probed by custom code, e.g.:
- USB storage
- Keyboard
- Ethernet
With driver model this approach doesn't work very well. We could build
a picture of the bus and then go back and add the devices later, but
this means that the data structures are incomplete for quite a while.
It also does not follow the model of being able to bind a device when we
discover it.
We would prefer to have devices automatically be bound as the device is
enumerated. This allows us to attach drivers to particular USB classes
or product/vendor IDs. This is the method used by Linux.
Add the required #defines from Linux, a way of declaring a USB driver and
the logic to locate the correct driver given the USB device's descriptors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a way for EHCI controller drivers to support driver model. Drivers can
call ehci_register() to register themselves in their probe() methods.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The index cannot be used with driver model, and isn't needed anyway. Change
the parameter to a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are a pain with driver model because we might have different EHCI
drivers which want to implement them differently. Now that they use
consistent function signatures, we can in good conscience move them to
a struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Fix non-driver-model EHCI to set up the EHCI operations correctly:
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the bulk of the code in usb_lowlevel_init() into a separate function
which will also be used by driver model. Keep the CONFIG options out of
this function by providing a tweak flag for Faraday. We need to avoid using
CONFIG options in driver model code where possible, since it makes it
impossible to use multiple controllers in that code where they have
different options.
The CONFIG_EHCI_HCD_INIT_AFTER_RESET option is also kept out of the
common init function. With driver model the controller will be able to
perform this extra init itself after registering with the EHCI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With driver model we want to remove the controller pointer in struct udevice
and use driver model data structures instead. To prepare for this, move
access to this field to a function which can provide a different
implementation for driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller. This makes the weak functions
use a consistent API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller. This makes the weak functions
use a consistent API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We don't need this anymore, so adjust the code to avoid using it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Adjust this function so that it is passed an EHCI controller pointer so that
implementations can look up their controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present the tegra driver uses a separate pointer to know which controller
type is in use. This works because only one controller type is used at a
time.
With driver model we want to make the controller state hermetic in the sense
that it is not necessary to look elsewhere to know the controller type. This
will permit a controller to implement the EHCI weak functions without
reference to global data structures.
To achieve this, define an enum for the controller type and store it with
the information on each EHCI controller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
