The Blackfin on-chip MAC driver was being managed in the BF537-STAMP board
directory, but it is not board specific, so relocate it to the drivers dir
so that other Blackfin ports can utilize it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the "ssync" instruction may have hardware anomalies associated with
it, have the smc91111 driver use the SSYNC macro rather than invoking it
directly. We workaround all the anomalies via this macro.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
For historical reasons we limited the stack to 256M because some boards
could only map that much via BATS. However newer boards are capable of
mapping more memory (for example 85xx is capble of doing up to 2G).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a simple expr style command that will set an env variable as the result
of the command. This allows us to do simple math in shell. The following
operations are supported: &, |, ^, +, -, *, /.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add setup_c0_status from Linux. For the moment we disable interrupts, set
CU0, mark the kernel mode, and clear ERL and EXL. This is good enough for
reset-time configuration and will work well across most processors.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Without this change, we'll be suffering from deffered WATCH exception
once Status.EXL is cleared. Make sure Cause.WP is cleared.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
We do Hit_Writeback_Inv_D and Hit_Invalidate_I. You might think that you
don't need to do Hit_Invalidate_I, but flush_cache() needs it since this
function is used not only in U-Boot specfic programs but also at loading
target binaries.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Currently we do 1) Index_Store_Tag_I, 2) Fill and 3) Index_Store_Tag_I
again per a loop for I-cache initialization. But according to 'See MIPS
Run', we're encouraged to use three separate loops rather than combining
them *for both I- and D-cache*. This patch tries to fix this.
In accordance with fixing above, mips_init_[id]cache are separated from
mips_cache_reset(), and rewrite cache loops are completely rewritten with
useful macros.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
This patch replaces the current function definitions with NESTED, LEAF
and END macro. They specify some more additional information about the
function; an alignment of symbol, type of symbol, stack frame usage, etc.
These information explicitly tells the assembler and the debugger about
the types of code we want to generate.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
The initial intension of having mips_cache_lock() was to use the cache
as memory for temporary stack use so that a C environment can be set up
as early as possible.
But now mips_cache_lock() follow lowlevel_init(). We've already have the
real memory initilaized at this point, therefore we could/should use it.
No reason to lock at all.
Other problems:
Cache locking is not consistent across MIPS implementaions. Some imple-
mentations don't support locking at all. The style of locking varies -
some support per line locking, others per way, etc. Some parts use bits
in status registers instead of cache ops. Current mips_cache_lock() is
not necessarily general-purpose.
And this is worthy of special mention; once U-Boot/MIPS locks the lines,
they are never get unlocked, so the code relies on whatever gets loaded
after U-Boot to re-initialize the cache and clear the locks. We're sup-
posed to have CFG_INIT_RAM_LOCK and unlock_ram_in_cache() implemented,
but leave the situation as it is for a long time.
For these reasons, I proposed the removal of mips_cache_lock() from the
global start-up code.
This patch adds CFG_INIT_RAM_LOCK_MIPS to make existing users aware that
*things have changed*. If he wants the same behavior as before, he needs
to have CFG_INIT_RAM_LOCK_MIPS in his config file.
If we don't have any regression report through several releases, then
we'll remove codes entirely.
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Acked-by: Andrew Dyer <amdyer@gmail.com>
If the LWMON5 config has SYSMON POST among CONFIG_POSTs which may be
run on the board, then the SYSMON POST controls the display backlight
(doesn't switch backlight ON if POST FAILED, and does switch the
backlight ON if PASSED).
If not, then the video driver controls the display backlight (just
switch ON the backlight upon initialization).
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
In current source code, when the device number of PCI is 0, process PCI
bridge without fail. However, when the device number is 0, it is not PCI
always bridge. There are times when device of PCI allocates.
When CONFIG_PCI_SKIP_HOST_BRIDGE is enable, this problem is solved when
use this patch.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Stefan Roese <sr@denx.de>
Disable default building of new uImage format support in preparation
for merge with the master. Support for new format can be enabled on
a per-board basis, by defining the following in the board's config file:
#define CONFIG_FIT 1
#define CONFIG_OF_LIBFDT 1
This can be optionally defined to give more verbose output:
#define CONFIG_FIT_VERBOSE 1 /* enable fit_format_{error,warning}() */
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Fix imxtract command not being compiled-in despite CONFIG_CMD_XIMG being in
include/config_cmd_default.h. Fix few warnings and handling of new format
images.
Signed-off-by: Bartlomiej Sieka <tur@semihalf.com>
Modify the RTC API to provide one a status for the time reported by
the rtc_get() function:
0 - a reliable time is guaranteed,
< 0 - a reliable time isn't guaranteed (power fault, clock issues,
and so on).
The RTC chip drivers are responsible for providing this info if the
corresponding chip supports such functionality. If not - always
report that the time is reliable.
The POST RTC test was modified to detect the RTC faults utilizing
this new rtc_get() feature.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
- insert partition for dtb blob to TQM5200B MTD layout
- set env variables dependent on the configured board
(TQM5200 or TQM5200B)
Signed-off-by: Martin Krause <martin.krause@tqs.de>
With this patch we don't need that many #ifdef's in the code. It moves
the subtraction into the macro and defines a NOP-macro when
CONFIG_FLASH_SHOW_PROGRESS is not defined.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Since fdt_node_offset_by_compatible() was converted to the new
fdt_next_node() iterator, a chunk of initialization code became
redundant, but was not removed by oversight. This patch cleans it up.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Currently the CHECK_HEADER() macro is defined local to fdt_ro.c.
However, there are a handful of functions (fdt_move, rw_check_header,
fdt_open_into) from other files which could also use it (currently
they open-code something more-or-less identical). Therefore, this
patch moves CHECK_HEADER() to libfdt_internal.h and uses it in those
places.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
fdt_add_subnode_namelen() has a bug if asked to add a subnode to a
node which has NOP tags interspersed with its properties. In this
case fdt_add_subnode_namelen() will put the new subnode before the
first NOP tag, even if there are properties after it, which will
result in an invalid blob.
This patch fixes the bug, and adds a testcase for it.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
This patch adds an fdt_next_node() function which can be used to
iterate through nodes of the tree while keeping track of depth. This
function is used to simplify the iteration code in a lot of other
functions, and is also exported for use by library users.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>