Silence the "Driver Model for Ethernet drivers" migration warning for
the bcm7445 and bcm7260 ports, neither of which supports networking yet.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is not required for sysboot (we defined fdtfile), let's save a few
bytes in the binary image without these variables.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Toradex product is called apalis-imx8 consisting of SoM with
i.MX8QM and i.MX8QP SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The size of the binary created with the default U-boot config is much
greater than the default offset for environment `0x60000`.
In case if that binary is used for booting via MMC it is overlapped with
the environment stored on MMC.
This leads to U-Boot corruption while saving environment with `saveenv`
command and non-bootable SabreLite board.
The offset for environment `CONFIG_ENV_OFFSET=0x60000` was added in
commit a09fea1 but did not count in the change to `0xC0000` if option
`CONFIG_ENV_IS_IN_MMC` is used.
The offset is also used for variant with environment saving onto SPI NOR
flash (with enabled option `CONFIG_ENV_IS_IN_SPI_FLASH`). In that case the
U-Boot binary flashed on SPI NOR is also corrupted after environment
saving with the original 0x60000 offset.
Signed-off-by: Denis Pynkin <denis.pynkin@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: a62c60610f("colibri_imx7_emmc: add Colibri iMX7D 1GB (eMMC) module support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: 304042c1f3("colibri_vf: set fdtfile for distroboot")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.
This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.
Fixes: board: 31b1e17f44("toradex: add Colibri iMX6ULL support")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
enable DTS support for keymile mpc83xx based boards.
get rid of compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Therefore done:
- add DTS for all mpc83xx based boards from keymile
mainly they are not mainlined to linux.
- add u-boot specific dtsi
- add stdout-path
- add missing ucc4 par_io definitions, which were
in board code, but not in linux DTS
- remove not used ethernet nodes
Signed-off-by: Heiko Schocher <hs@denx.de>
Patch-cc: Mario Six <mario.six@gdsys.cc>
Patch-cc: Qiang Zhao <qiang.zhao@nxp.com>
Series-to: u-boot
Series-version: 3
Series-changes: 3
- rebase patchset to current mainline commit
c0192950df
- update defconfig files
Series-changes: 2
- add patch which fixes Codingstyle errors in drivers/qe
- add patch which converts the mpc83xx based boards from
keymile to DM_ETH
Cover-letter:
powerpc, mpc83xx: add DM_ETH support
This patch series adds DM ethernet support for mpc83xx based
keymile boards.
Travis build:
END
am335x internal SRAM is too small to support the addition of
SPI bootmode to the default defconfig. Add a separate spiboot_defconfig
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Enable the FS_LOADER and associated configs in the j7200_evm_r5_defconfig
so that the R5 SPL can support the loading of firmware files from a boot
media/file system.
Signed-off-by: Suman Anna <s-anna@ti.com>
The A72 U-boot can support early booting of any of the Main or MCU R5F
remote processors from U-boot prompt to achieve various system usecases
before booting the Linux kernel. Update the default BOOTCOMMAND to provide
an automatic and easier way to start various remote processors through
added environment variables.
Signed-off-by: Suman Anna <s-anna@ti.com>
The J7200 SoCs has two R5F sub-systems. Enable the TI K3
R5F remoteproc driver and the remoteproc command options
to allow these R5F processors to be booted from A72 U-Boot.
The Kconfigs are added using savedefconfig.
Signed-off-by: Suman Anna <s-anna@ti.com>
Enable configs required to support HyperFlash boot and detection of
onboard mux switch for HyperFlash selection
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Enable options SYS_WHITE_ON_BLACK to permit HDMI background
screen from white to back, also enable USB_KEYBOARD.
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Supporting USB keyboards out of the box is both handy for development
and production. Notably if u-boot is used to boot into GRUB. This patch
adds USB keyboard support for 32 bit RPi4 config.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Enable support of ISSI SPI flashes found on EspressoBIN boards
Change-Id: I6de61c48f108fb4f410f321b9db45887d23212e5
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/61455
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Chulski <stefanc@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Include support for CONFIG_SPI_FLASH_GIGADEVICE for supporting
newly produces EspressoBin boards (v7)
Change-Id: I5d4b972cbe2ee5a9d52ce9908794ad4e1b59ee3b
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/61236
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
For testing automated updates via dfu and mtd we need the dfu and mtd
commands as well as preboot support.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Due to different partition layouts in different U-Boot versions, DTS for
Espressobin in Linux does not contain any definition of MTD partitions.
See commit https://git.kernel.org/stable/c/00954566464a4 for more details.
This patch via ft_board_setup() hook fills current partition layout used by
U-Boot, so booted kernel would see correct MTD partitions layout.
U-Boot env partition is calculated from CONFIG_ENV_OFFSET option.
First partition contains secure firmware, ARM trusted firmware and U-Boot
with checksums. So it is not possible to replace just one image (e.g.
U-Boot) without updating other parts where is stored checksum of U-Boot.
Therefore there is no extra partition defined for U-Boot and first
partition is called just 'firmware'.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Tested-by: Andre Heider <a.heider@gmail.com>
Espressobin board comes with Marvell's U-Boot version where U-Boot env is
stored in SPI at offset 0x3F0000. This patch changes env offset in
Espressobin defconfig file to match Marvell's U-Boot version.
Users who want to use previous or different env offset can still change it
in .config file when compiling U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
Enabled SDIO slot 0 (south bridge) for SD card on
Espressobin board.
Change-Id: I51a2debf9fba276b9c4a2bc6da91328d47f443e3
Signed-off-by: Wilson Ding <dingwei@marvell.com>
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-on: http://vgitil04.il.marvell.com:8080/60945
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
[pali: Define cd-gpios and enable CONFIG_DM_REGULATOR_GPIO]
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Andre Heider <a.heider@gmail.com>
CMD_ADC selected DM_REGULATOR unconditionally without enabling DM.
That's why change select to depends on to cover it.
Kconfig is showing this issue as:
WARNING: unmet direct dependencies detected for REGMAP
Depends on [n]: DM [=n]
Selected by [y]:
- DM_REGULATOR_PBIAS [=y] && DM_REGULATOR [=y]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Update CMD_ADC=y configs to enable DM_REGULATOR now]
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add basic Marvell/Cavium OcteonTX/TX2 support (Suneel)
- Infrastructure changes to PCI uclass to support these SoC's (Suneel)
- Add PCI, MMC & watchdog driver drivers for OcteonTX/TX2 (Suneel)
- Increase CONFIG_SYS_MALLOC_F_LEN for qemu-x86 (Stefan)
- Sipeed Maix support S-mode.
- Provide command sbi.
- Use fdtdec_get_addr_size_auto_parent to get fu540 cache base address.
- Fix a compiler error with CONFIG_SPL_SMP=n.
- Fix sifive ram driver 32 compiler warnings.
- Fix kendryte/pll.h redefine nop() warning.
With the upcoming increase of the malloc area in U-Boot
("pci: pci-uclass: Dynamically allocate the PCI regions"), the CI QEMU
x86 test fails:
U-Boot 2020.10-rc2-g0a668f6d38 (Aug 25 2020 - 06:12:51 +0000)
alloc space exhausted
Error binding driver 'cpu_qemu': -12
Some drivers failed to bind
alloc space exhausted
initcall sequence fff6a760 failed at call fff13b3d (err=-19)
This patch now increases CONFIG_SYS_MALLOC_F_LEN to 0x1000, which is
already used on qemu-x86_64_defconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
As explained in the CONFIG_DM_MDIO text inside drivers/net/Kconfig:
"Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces."
i.MX6 has a single FEC instance, so there is no need to select
CONFIG_DM_MDIO.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
We have a number of platforms that are a combination of a carrier board
and System-on-Module (SoM) that in turn allows for the board to have
different SoCs on it. In some cases, this is handled via board-specific
Kconfig options. In other cases we make use of
CONFIG_SYS_EXTRA_OPTIONS. This latter case however can lead to invalid
configurations as we will not in turn get options that in Kconfig are
selected by or depend on that setting.
To resolve this, make the SoC option a choice in Kconfig and make boards
depend on what they can support. This change opens us up for further
clean-ups in the cases where a single CONFIG_TARGET_xxx can support
different SoCs and today they do not, or do not cleanly do so.
Reported-by: Matt Porter <mporter@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Soeren Moch <smoch@web.de>
Cc: Markus Niebel <Markus.Niebel@tq-group.com>
Cc: Igor Opaniuk <igor.opaniuk@toradex.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Akshay Bhat <akshaybhat@timesys.com>
Cc: Ken Lin <Ken.Lin@advantech.com.tw>
Cc: Ian Ray <ian.ray@ge.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Raffaele RECALCATI <raffaele.recalcati@bticino.it>
Cc: Simone CIANNI <simone.cianni@bticino.it>
Cc: Adam Ford <aford173@gmail.com>
Cc: Marcin Niestroj <m.niestroj@grinn-global.com>
Cc: "Eric Bénard" <eric@eukrea.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Cc: Eric Nelson <eric@nelint.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Parthiban Nallathambi <parthiban@linumiz.com>
Cc: Marek Vasut <marex@denx.de>
Cc: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Niel Fourie <lusus@denx.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Silvio Fricke <open-source@softing.de>
Tested-by: Matt Porter <mporter@konsulko.com> [colibri_imx6]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch adds support for all OcteonTX2 96xx/95xx
boards from Marvell.
For 96xx boards, use octeontx_96xx_defconfig and
for 95xx boards, use octeontx_95xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
This patch adds support for all OcteonTX 81xx/83xx
boards from Marvell.
For 81xx boards, use octeontx_81xx_defconfig and
for 83xx boards, use octeontx_83xx_defconfig.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Enable PCI memory regions in ranges property to be of multiple entry.
This helps to add support for SoC's like OcteonTX/TX2 where every
peripheral is on PCI bus.
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Provide a defconfig that can be used to build U-Boot for the Maix boards
running upon OpenSBI.
Update the documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
CONFIG_CMD_RUN is set on by default in Kconfig.
Create xenguest_arm64_defconfig by using savedefconfig to avoid unnecessary
options.
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Total Compute is based on ARM architecture and has
the following features enabled in u-boot:
- PL011 UART
- PL180 MMC
- NOR Flash
- FIT image with Signature
- AVB
Signed-off-by: Usama Arif <usama.arif@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPLASH_SCREEN
CONFIG_SPLASH_SCREEN_ALIGN
CONFIG_SPLASHIMAGE_GUARD
CONFIG_SPLASH_SOURCE
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove adhoc dt binding for fixed-partition definition for i2c eeprom.
fixed-partition are using reg property instead of offset/size pair.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
