Corrected the order of arguments in memset in run_descriptor
function. Wrong order of argumnets led to improper initialization
of members of struct type result. This resulted in RNG instantiation
error.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
we need to differentiate dual-role MACs into two types: MACs with
10GEC enumeration consistent with DTSEC enumeration(defined by
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION) and other MACs without
CONFIG_FSL_FM_10GEC_REGULAR_NOTATION defined.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For DDR controller version 4.7 or newer, MRC_CYC (mode register set
cycle time) is max(tMRD, tMOD). tMRD is 4nCK, or 8nCK (RDIMM). tMOD
is max(12nCK, 15ns) according to JEDEC spec.
DDR4 is not affected by this change.
Signed-off-by: York Sun <yorksun@freescale.com>
'eccstat' array elements might be used uninitialized
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Check USB Erratum A007792 applicability. If applicable, add
corresponding property in the device tree via device tree fixup
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add a new framework for fsl usb erratum handling to standardize
erratum checking only inside Uboot. Information to kernel is passed
via a boolean property corresponding to erratum, hence eliminating
need for code duplication inside kernel
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The macro __iomem is defined in include/linux/compiler.h.
Let's include it rather than double __iomem defines.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
pl010 & pl011 have different control register offsets, setting it as per
the pl01x type.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Receive line control uses same setting as transmit line control, also one lcrh
write is effective for both baud rate & receive line control internal update.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
UART_IBRD, UART_FBRD, and UART_LCR_H form a single 30-bit wide register which
is updated on a single write strobe generated by a UART_LCR_H write. So, to
internally update the content of UART_IBRD or UART_FBRD, a write to UART_LCR_H
must always be performed at the end.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Although we were checking the pl01x type, seems like PL010 type was being
passed by mistake.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Due to an uninitialised variable, when muxes were deselected, any value
could be written to the mux control register. On the PCA9548, this could
result in multiple channels being selected, thus enabling multiple
pull-up resistors, and much bus capacitance.
The fix is simply to initialise the written value to zero.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
VSC8514 QSGMII PHY requires enabling auto-negotiation,
otherwise it wouldn't work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Some UDIMMs have faulty SPD with wrong mapping for DQ[36-39].
Using raw card spec in case this error is detected.
Signed-off-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Cortina CS4315/CS4340 10G PHY.
- This driver loads CS43xx firmware from NOR/NAND/SPI/SD device
to initialize Cortina PHY.
- Cortina PHY has non-standard offset of PHY ID registers, thus
we define own get_phy_id() to override default get_phy_id().
- To define macro CONFIG_PHY_CORTINA will enable this driver.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase write-to-write and read-to-read turnaround time for two-slot DDR
configurations. Previously only quad-rank and two dual-rank configurations
have this additional turnaround time. A recent test on two single-rank
DIMMs shows the shorter additional turnaround time is also needed.
Signed-off-by: York Sun <yorksun@freescale.com>
fman_port_enet_if() tests if FM1_DTSEC2 or FM1_DTSEC4 uses
RGMII or MII and if not returns PHY_INTERFACE_MODE_NONE.
This excludes testing for SGMII further down.
Remove the unconditional "else return PHY_INTERFACE_MODE_NONE"
so SGMII can be tested too.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Reviewed-by: York Sun <yorksun@freescale.com>
The same problem that is seen on some OMAP3 is also seen on some OMAP4
so include them in the test in order to prevent some hangs during SPL.
[trini: Re-word commit message, make apply cleanly]
Signed-off-by: Tom Rini <trini@ti.com>
The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.
Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:
Without NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.947 seconds, 2947 ticks
With NAND ready pin:
U-Boot# time nand read 80400000 0 400000
NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK
time: 2.795 seconds, 2795 ticks
So an increase of approx. 5%.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
Renesas R-Mobile/R-Car ARM SoC of MMC has the same IP that are supported by
sh_mmcif. This adds support R-Mobile/R-Car ARM SoC with the setting of the
clock support.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Maximum value and the minimum value of clock for sh_mmcif instead by
base of MMC clock. This removes fixed clock, make the changes to be calculated
according to environment.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use DIV_ROUND_UP and fls to simplify the code.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not every device has multiple MMC slots available, so it makes sense to enable
only the required LDOs for the available slots. Generic code in omap_hsmmc will
enable both VMMC1 and VMMC2, in doubt.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
Some devices may use non-standard combinations of regulators to power MMC:
this allows these devices to provide a board-specific MMC power init function
to set everything up in their own way.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
there's no such function usb3_phy_power(),
it's likely that author meant to call,
usb_phy_power() instead, but that's already
called properly from xhci-omap.c.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
- fix crash when sata device is not initialized
- remove disable_sata_clock() since it is not clear which clock for which
device should be disabled here
- call disable_sata_clock() for mx6 in preboot_os instead
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Leave the OCOTP turned on, so that we subsequent access do not fail.
After enabling the thermal driver on a mx6sxsabresd board:
U-Boot 2015.01-rc1-18267-g99d4189-dirty (Nov 24 2014 - 12:59:01)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 48 C
Reset cause: POR
Board: MX6SX SABRE SDB
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
00:01.0 - 16c3:abcd - Bridge device
01:00.0 - 8086:08b1 - Network controller
In: serial
Out: serial
Err: serial
Net:
(hang)
As the thermal driver accesses the ocotp registers, its clock will be disabled
afterwards.
Then when the MAC address is read (also from ocotp registers) it will cause a
hang.
Do not disable the ocotp clock to prevent this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Printing the calibration data on every boot does not provide really useful
information:
U-Boot 2015.01-rc1-18266-ge7eb277 (Nov 24 2014 - 11:29:51)
CPU: Freescale i.MX6Q rev1.2 at 792 MHz
CPU: Thermal calibration data: 0x5d85067d
CPU: Temperature 33 C
Reset cause: POR
Board: MX6-SabreSD
Do not display the calibration data in order to have a cleaner boot log.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
