Add dts and defconfig for Banana-pi M3 board.
It has 2G LPDDR3, UART, ethernet, USB, HDMI, USB Sata, MIPI DSI,
mic, AP6212 Wifi, etc on it.
It is paired with AXP813 PMIC which is almost same as AXP818.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
[hdegoede@redhat.com: rename to Sinovoip_BPI_M3_defconfig/sun8i-a83t-sinovoip-bpi-m3.dts]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.
This adds groundwork to support for new DRAM type for A83T.
Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Now that we support PSCI and various security switches, we can let
U-boot boot Linux into non-secure and HYP mode.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory. These values
define the voltage requirements for the chip. u-boot reads
FUSESR and translates the values into the appropriate
commands to set the voltage output value of an external
voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IR chip on all the boards are required to be used in Intel mode
to support VID. VDD will not be adjusted if IR chip is used in
other modes.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Users migrating Freescale's PowerPC SoC U-Boot code to their custom
board, often overlook the need to execute set_liodns() and
setup_portals() being called by platform files.
So Move set_liodns() and setup_portals() to common u-boot boot
sequence
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some images to be validated are relocated to a dynamic
address at run time. So, these addresses cannot be known
befor hand while signing the images and creating the header
offline.
So, support is required to pass the image address to the
validate function as an argument.
If an address is provided to the function, the address
field in Header is not read and is treated as a reserved
field.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The code for image hash calculation, hash calculation from
RSA signature and comparison of hashes has been mobed to a
separate function.
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Separate functions are created for reading and checking the
sanity of Public keys:
- read_validate_single_key
- read_validate_ie_tbl
- read_validate_srk_table
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The prototype and defination of function fsl_secboot_validate
has been changed to support calling this function from another
function within u-boot.
Only two aruments needed:
1) header address - Mandatory
2) SHA256 string - optional
Signed-off-by: Saksham Jain <saksham@freescale.com>
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
1.Use "qixis_reset sd" to boot from SD
2.Use "qixis_reset sd_qspi" to boot from SD with QSPI support
3.Use "qixis_reset qspi" to boot from QSPI flash
On some SoCs such as LS1021A and LS1043A, IFC and QSPI could be
pin-multiplexed. So the switches are different between SD boot with
IFC support and SD boot with QSPI support. The default booting from
SD is with IFC support.
Once QSPI is enabled(IFC disabled), only use I2C to access QIXIS.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch also exposes the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
With gcc 4.9, it produces the following warnings:
CC board/tqc/tqm834x/tqm834x.o
board/tqc/tqm834x/tqm834x.c: In function 'initdram':
board/tqc/tqm834x/tqm834x.c:325:12: warning: iteration 3u invokes undefined behavior [-Waggressive-loop-optimizations]
(((base + size - 1) >> CSBNDS_EA_SHIFT) &
^
board/tqc/tqm834x/tqm834x.c:80:2: note: containing loop
for(cs = 0; cs < 4; ++cs) {
^
There is an integer overflow when cs = 3. To fix it, change
parameters of set_cs_bounds() to ulong.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently buildman fails to build sh7753evb and reports the following:
board/renesas/sh7753evb/built-in.o: In function 'init_gether_mdio':
board/renesas/sh7753evb/sh7753evb.c:94: undefined reference to 'PMB_ADDR_BASE'
board/renesas/sh7753evb/sh7753evb.c:94: undefined reference to 'PMB_DATA_BASE'
board/renesas/sh7753evb/sh7753evb.c:94: undefined reference to 'mk_pmb_addr_val'
board/renesas/sh7753evb/sh7753evb.c:94: undefined reference to 'mk_pmb_data_val'
make: *** [u-boot] Error 1
The fix is to wrap any codes that access these macros with CONFIG_SH_32BIT.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add pinmux settings.
Add related macro definitions.
Nand pin conflicts with emmc, so if want to enable nand, need to do
hardware rework. After hardware rework, define CONFIG_NAND_MXS in
board header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As the lowlevel_init function is empty we should better
remove this assembly file entirely and use a dummy C
function instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Instead of calling the northbridge and PCH init from bd82x6x_init_extra()
when the PCI bus is probed, call it from the respective drivers. Also drop
the Northbridge init as it has no effect. The registers it touches appear to
be read-only.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This board includes an RK3288 SoC on a SOM. It can be mounted on a
base-board which provides a wide range of peripherals.
So far this is verified to boot to a prompt from a microSD card. The serial
console works as well as HDMI.
Thanks to Tom Cubie for sending me a board.
Signed-off-by: Simon Glass <sjg@chromium.org>
We will save boot mode flag in grf's os_reg[4], if fastboot
requested or fastboot key pressed, try to enter fastboot mode
at preboot stage.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs
Signed-off-by: Heiko Schocher <hs@denx.de>
Now that driver model support is available, convert sandbox over to use it.
We can remove a few of the special hooks that sandbox currently has.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
- move chip reset to separate function
- use CONFIG_SMC911X_BASE instead of hardcoded value
- remove unneeded local variable from board_eth_init.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The include/configs/yucca.h already has the same define:
#define CONFIG_SYS_TEXT_BASE 0xfffb0000
Remove the redundant one from board/amcc/yucca/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stefan Roese <sr@denx.de>
We can delete board/pb1x00/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We can delete board/dbau1x00/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
We can delete board/micronas/vct/config.mk by moving the define of
CONFIG_SYS_TEXT_BASE to somewhere else. Other MIPS boards are
still defining it in include/config/${BOARD}.h, so I am following
that way here.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is how CONFIG options are defined by Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
The board/freescale/m54418twr/config.mk defined TEXT_BASE, which has
the same value as CONFIG_SYS_TEXT_BASE. The TEXT_BASE is referenced
by two files:
- arch/m68k/cpu/mcf5445x/start.S and include/
- include/configs/M54418TWR.h
Replace the references with CONFIG_SYS_TEXT_BASE and delete
board/freescale/m54418twr/config.mk.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
For historical reason, CONFIG_SYS_TEXT_BASE has been specified
in various ways:
[1] by board/${VENDOR}/${BOARD}/config.mk
[2] by CONFIG_SYS_EXTRA_OPTIONS
(This was "options" field of boards.cfg before Kconfig conversion)
[3] by include/configs/${BOARD}.h
[4] by configs/${BOARD}_defconfig
Most of M68K boards use either [1] or [2], both of which we want to
deprecate. Switch them into [4], which is the newest way (Kconfig).
We still allow [3] too, because it is still used by many boards and
we expect much time for conversion.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Angelo Dureghello <angelo at sysam.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change the dram_init() function on ThunderX to query ATF services for
the real installed DRAM size
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Use void pointers as address argument for readl( and writel()).
This is required for the upcoming MIPS asm header file and I/O
accessor update.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use void pointer as address argument for readl(). This is required
for the upcoming MIPS asm header file and I/O accessor update.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Synology keeps per item configuration in a dedicated 'partition' in SPI
flash, namely the one named 'vendor' in DTS file. It contains the two
NICs MAC addresses as well as the item's serial number. I didn't find a
way to have this information extracted automatically, therefore
implemented 'syno populate_env' command which extracts the three values
and puts them into environment. To make things permanent though, one has
to 'saveenv'.
Another command is 'syno clk_gate', which allows to change the clock
gating which is done in DS414 board file.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for the MV78230 based DS414 NAS by Synology. The
relevant bits have been extracted from the 'synogpl-5004-armadaxp'
package Synology kindly published, garnished with a fair amount of
trial-and-error.
Sadly, support is far from perfect. The major parts I have failed in
are SATA and XHCI support. Details about these and some other things
follow:
Device Tree
-----------
The device tree file armada-xp-synology-ds414.dts has been copied from
Linux and enhanced by recent U-Boot specific changes to
armada-xp-gp.dts.
SATA Support
------------
There is a Marvell 88SX7042 controller attached to PCIe which is
supported by Linux's sata_mv driver but sadly not U-Boot's sata_mv.
I'm not sure if extending the latter to support PCI devices is worth the
effort at all. Porting sata_mv from Linux exceeded my brain's
capacities. :(
XHCI Support
------------
There is an EtronTech EJ168A XHCI controller attached to PCIe which
drives the two rear USB3 ports. After a bit of playing around I managed
to get it recognized by xhci-pci, but never was able to access any
devices attached to it. Enabling it in ds414 board config shows that it
does not respond to commands for whatever reason. The (somewhat) bright
side to it is that it is not even supported in Synology's customized
U-Boot, but that also means nowhere to steal the relevant bits from.
EHCI Support
------------
This seems functional after issuing 'usb start'. At least it detects USB
storage devices, and IIRC reading from them was OK. OTOH Linux fails to
register the controller if 'usb start' wasn't given before in U-Boot.
According to Synology sources, this board seems to support USB device
(gadget?) mode. Though I didn't play around with it.
PCIe Support
------------
This is fine, but trying to gate the clocks of unused lanes will hang
PCI enum. In addition to that, pci_mvebu seems not to support DM_PCI.
DDR3 Training
-------------
Marvell/Synology uses eight PUPs instead of four. Does not look like
this is meant to be customized in mainline U-Boot at all. OTOH I have
no idea what a "PUP" actually is.
PEX Init
--------
Synology uses different values than mainline U-Boot with this patch:
pex_max_unit_get returns 2, pex_max_if_get returns 7 and
max_serdes_lines is set to 7. Not changing this seems to not have an
impact, although I'm not entirely sure it does not cause issues I am not
aware of.
Static Environment
------------------
This allows to boot stock Synology firmware at least. In order to be a
little more flexible when it comes to booting custom kernels, do not
only load zImage partition, but also rd.gz into memory. This way it is
possible to use about 7MB for kernel with piggyback initramfs.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Merging all the board specific Kconfig options into the main Kconfig file
for mach-mvebu makes things easier to maintain.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This cleans up the mux configuration a bit, setting mmc clock signals to input
enabled and specifying pull-down (0) when pull is not used.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Do not set HAVE_INTEL_ME by default as for some cases Intel ME
firmware even does not reside on the same SPI flash as U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
'sf command' should receive the length in sector boundaries, so fix it
accordingly.
Also, show the steps to set the server and board IP addresses for
making the steps clearer.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We currently support various versions of Solidrun mx6 boards, so
remove the obsolete comment.
Reported-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Since commit 59370f3fcd ("net: phy: delay only if reset handler is
registered") Ethernet is no longer functional:
Booting from net ...
FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
This commit does not have an issue in itself, but it revelead a problem
with the Ethernet initialization.
As per the AR8035 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and keep the reset low for 10ms.
Also add a 100us delay after deasserting the reset line
to guarantee that the PHY ID can be read correctly and the Atheros
PHY can be loaded as per Troy Kisky's suggestion.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Tom Rini <trini@konsulko.com>
According to the Coverity result, a unsigned int variable is used fo less-
than-zero comparison, the result is never true. Need to fix the variable
type to signed int.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
As per the AR8031 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.
This results in a simpler code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As per the AR8031 datasheet:
"For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset
1ms requirement is satisfied."
So do as suggested and also add a 100us delay after deasserting the
reset line to guarantee that the PHY ID can be read correctly and the
Atheros 8031 PHY driver can be loaded automatically.
This results in a simpler code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In pci_map_region(), pass 'range_id' to fdt_read_range(),
otherwise the same address will be mapped again in other
calls to pci_map_region()
Signed-off-by: Miao Yan <yammiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Move setup_display from board_early_init_f to board_init.
Add more clock settings.
Add blacklight iomux setting.
Add display_info_t info for the lvds screen.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Use the macro SETUP_IOMUX_PAD(...) rather than imx_iomux_v3_setup_multiple_pads(...) in order to setup
the pin configuration for ECSPI1.
ARRAY_SIZE(pads) provides the wrong size for imx_iomux_v3_setup_multiple_pads(pads, ARRAY_SIZE(pads)) in
case of MX6QDL. In the particular case, the content of GPR12 is overwritten and the IPG/AHB/ATB/ATP clocks
are deactivated. Therefore, the connection to the system via JTAG is not possible anymore. Furthermore,
kernel version 3.0.35 hangs during bootprocess in the function etm_init().
Signed-off-by: Michael Schanz <michael.schanz@congatec.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This symbol is not used anywhere, so remove it. For spear600, remove
it from the board file, since the symbol is not defined for spear600
either.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The Empire Electronix D709 tablet is a fairly standard 7" A13 tablet,
featuring usb-wifi, a micro-sd slot, micro-usb otg and headphone jack.
Empire Electronix is written on the back of the tablet, the D709 model
info can be found in the about tablet menu in android.
The PCB has no markings to speak of.
This dts file is identical to the one submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Drop all the common board code, since it is not completely useless.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
LL_TEMAC is available at big endian MB and it is not properly tested
that's why the patch removes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add ps7_init_gpl.c/h for the ZYBO board. This instance of the ps7_init
is generated by the Vivado 2015.3 tools using the system configuration
provided by Digilent located on their website.
Update the kconfig so that the defconfig is not overrided to use the
custom init ps7_init_gpl target by default.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: "Sören Brinkmann" <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The driver is actually for the Designware DWC2 controller.
This patch renames the global s3c_udc.h header to dwc2_udc.h.
The rename is done automatically:
$ sed -i "s/s3c_udc\.h/dwc2_udc.h/g" \
`git grep "s3c_udc\.h" | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the second and final to rename global symbol,
the s3c_udc_probe() function.
The rename is done automatically:
$ sed -i "s/s3c_udc_probe/dwc2_udc_probe/g" \
`git grep s3c_udc_probe | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the first to rename global symbol, the struct
s3c_plat_otg_data.
The rename is done automatically:
$ sed -i "s/s3c_plat_otg_data/dwc2_plat_otg_data/g" \
`git grep s3c_plat_otg_data | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.
In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.
Signed-off-by: York Sun <yorksun@freescale.com>
DDR has been set as secure in MMU tables. Non-secure master such
as SDHC DMA cannot access data correctly. Mixing secure and non-
secure MMU entries requirs the MMU tables themselves in secure
memory. This patch moves MMU tables into a secure DDR area.
Early MMU tables are changed to set DDR as non-secure. A new
table is added into final MMU tables so secure memory can have
2MB granuality.
gd->secure_ram tracks the location of this secure memory. For
ARMv8 SoCs, the RAM base is not zero and RAM is divided into several
banks. gd->secure_ram needs to be maintained before using. This
maintenance is board-specific, depending on the SoC and memory
bank of the secure memory falls into.
Signed-off-by: York Sun <yorksun@freescale.com>
