Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds support for the SMSC9500 with product id 0x9900 which is
equipped in the "EXSYS USB 2.0" etherner USB adapter.
Tested on omap3_beagle.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
There are many musb prints in SPL and U-Boot log.
These prints are required only during musb debug.
So replacing printk with pr_debug in musb_core.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.
Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Fixes NFS root problems with Beagle (3530 ES1.0) when used with
external USB-ethernet adapter and "USB start" command used within
u-boot.
Soft resetting the UHH module causes instability issues on
all OMAPs so we just avoid it.
See OMAP36xx Errata
i571: USB host EHCI may stall when entering smart-standby mode
i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
On OMAP4/5, soft-resetting the UHH module can put it into
Smart-Idle mode and lead to a deadlock.
On OMAP3 this doesn't seem to be the case but still instabilities
are observed on beagle (3530 ES1.0) if soft-reset is used.
e.g. NFS root failures with Linux kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
This patch extends dfu code to support transmission with -R switch
specified at dfu-util.
When -R is specified, the extra USB_REQ_DFU_DETACH request is sent after
successful data transmission. Then dfu resources are released and reset
command is issued.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The requests sent to the controller are not properly cache aligned
most of the time, thus implement a simple bounce buffer to avoid
problem with cache.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Implement functions to flush/invalidate dcache over QH and qTDs
and make use of them where appropriate. Also use them to replace
the old incorrect cache management attempt. This is the first step
towards making this driver work with data cache enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The code for retrieving qTD item for particular endpoint is hard
to understand, moreover it's duplicated all over the driver. Move
the code into single nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Allocate the qTD items all at once instead of allocating them
separately. Moreover, make sure each qTD is properly aligned
to 32-bytes boundary and that cache can be safely flushed over
each qTD touple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The code for retrieving QH for particular endpoint is hard to understand,
moreover it's duplicated all over the driver. Move the code into single
nice and documented function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Check the length of system cacheline at compile-time and fail
if the system uses too long cachelines.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoint QH list has to be aligned to 10-bit boundary. We also have
to make sure the list is aligned on a cacheline boundary. Make sure it
is. Furthermore, check if the memory allocation for the QH list didn't
fail. Moveover, improve the comment about the QH list structure.
Finally, the qTD item list has to be aligned only to 5-bit boundary, not
10-bit as it is now, fix this as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Both the endpoint queue head and the endpoint item list is a controller
specific thing. Move them both into controller private data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
There is no need to init this field at runtime, so init it statically.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The QH_MAXNUM is used in absolutelly incorrect manner and is not
even needed. Remove it and correctly replace it's occurance with
2 * NUM_ENDPOINTS .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Clean up the code that checks the validity of a USB gadget driver
in usb_gadget_register_driver(). Moreover, limit the speed of the
driver to either FULL or HIGH, this is more precise and once we
have xHCI support, also more correct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The usb_lowlevel_init() call already fills and passes back struct
ehci_ctrl , which readily contains correctly determined address of
the port register block address computed from values from controller
configuration registers. Leverage this and make use of this value
as this makes the code mode universal, but also gets us rid of the
CONFIG_USB_REG_BASE configuration option.
Moreover, this patch cleans up the usb_gadget_register_driver() call
a little by correcting the error handling. Note the usb_lowlevel_init()
and mvudc_probe() are now called in reversed order, but this has no
impact on the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Move the struct ehci_ctrl defition from ehci-hcd.c into ehci.h
so it can be re-used by drivers. In particular, the mv_udc driver
can benefit from this move.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Move the constant values that are programmed into mv_ep.ep into
separate static const structure so they can be memcpy()'d when
the initialization happens.
Moveover, we only every init NUM_ENDPOINTS, not 2 * NUM_ENDPOINTS,
so fix this bug as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The endpoints are operated on a per-controller basis, move the
endpoint array into controller's private data. Also shuffle the
struct mv_ep structure definition just above the definition of
the struct mv_drv so they're well grouped together.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The mv_udc driver is broken for a while and doesn't even compile.
This patch fixes the issues and gets the driver into working state
again. This driver was tested on Freescale i.MX233/i.MX28 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
The DFU's state machine original implementation author and copyright were
missing.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
This patch fix the omap access to the transceiver
configuration registers using the ulpi bus. As reported by
the documentation the bit31 is used only to check if the
transaction is done or still running and the reading and
writing operation have different offset and have different
values. What we need to do at the end of a transaction is
leave the bus in done state. Anyway an error using the ulpi
omap register is not recoverable so any error give out the
usage of this interface.
Tested on a custom OMAP5430 board with a TUSB1210 ULPI PHY
on USBB1.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Lubomir Popov <lpopov@mm-sol.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
This trivial patch adds the definition of the vid/pid for the Ver C1 of the
USB Ethernet adapter D-Link DUB-E100.
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
CC: Marek Vasut <marex@denx.de>
This subtle change fix problem with too small amount of allocated
memory to store DFU function pointers.
One needs to allocate extra space for sentinel NULL pointer in this array
of function pointers.
With the previous code, the NULL value overwrites malloc internal data
and afterwards free(f_dfu->function) crashes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
add a weak dummy function g_dnl_fixup to add the possibility to update
the device_desc board specific. Used on the upcoming siemens board
support, where idVendor and idProduct is stored in an eeprom.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
- set in to_dfu_mode() f_dfu->dfu_state = DFU_STATE_dfuIDLE
as after every to_dfu_mode call this is done, so move
this into to_dfu_mode
- switch in dfu_bind() into dfu mode:
This fixes wrong "dfu-util -l" output, when calling
"dfu-util -l" after a board reset, without doing a
download before. See also discussion here:
http://lists.denx.de/pipermail/u-boot/2013-June/157272.html
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch memcpy is used instead of an assignment to
avoid unaligned access execption on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
This patch use get|put_unaligned_le16 to access structure data
to avoid data abort on some ARM platforms.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Marek Vasut <marex@denx.de>
Small conflict over DRA7XX updates and adding SRAM_SCRATCH_SPACE_ADDR
Conflicts:
arch/arm/include/asm/arch-omap5/omap.h
Signed-off-by: Tom Rini <trini@ti.com>
Without this, second usb_composite_register() call fails always
with -EINVAL.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Commit 8f62ca6 "usb: ehci: Support interrupt transfers via periodic list"
didn't include any cache management in the new interrupt transfer path.
It also added an extra write to or_asynclistaddr in usb_lowlevel_init(),
without having flushed out the data there.
Add the missing cache management calls, so that the code works again.
This allows the USB keyboard on Tegra's Seaboard/Springbank boards to
work.
Cc: Patrick Georgi <patrick@georgi-clan.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Faraday FOTG210 is an OTG chip which could operate
as either an EHCI Host or a USB Device at a time.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
There is at least one non-EHCI compliant controller (i.e. Faraday EHCI)
not only leave RESERVED and CONFIGFLAG registers un-implemented
but also has their address spaces removed.
As an result, the PORTSC register of Faraday EHCI always
starts from 0x30 instead of 0x44 in standard EHCI.
So that we'll need a weak-aliased function for abstraction.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
1. The 'index' of ehci_submit_root() is not always > 0.
e.g.
While it gets invoked from usb_get_descriptor(),
the 'index' is always a '0'. (See ch.9 of USB2.0)
2. The PORTSC register is not always required, and thus it
should only report a port error when necessary.
It would cause a port scan failure if the ehci_submit_root()
always gets terminated by a port error.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
Use get_unaligned() while fetching wMaxPacketSize to avoid
voilating any alignment rules.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Piotr Wilczek <p.wilczek@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Dalek <luk0104@gmail.com>
Cc: Marek Vasut <marex@denx.de>
The ASIX driver calls a basic_init() function during get_info(), so that
not all initialization tasks need to be redone on every init().
Unfortunately, the most important one is still triggered too often: the
driver does a full port and MII reset on every asix_init(), requiring up
to several seconds to reestablish the link.
This patch confines that software reset into the asix_basic_init()
function so that it will only be executed once. This saves about a
second of boot time on systems using BOOTP.
Note: this patch was previously submitted many moons ago as:
usb: usbeth: asix: Do a fast init if link already established
That patch seens to have been lost or forgotten, so this is a rebased
version. It is tested on snow with a Asix USB dongle (Cisco).
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
This commit broke USB2 on link (Chromebook Pixel):
020bbcb usb: hub: Power-cycle on root-hub ports
However the root cause seems to be a missing mask and missing 'break'
in ehci-hcd.c. This patch fixes both.
On link, 'usb start' with a USB keyboard and memory stick inserted now
finds both. The keyboard works as expected. Also ext2ls shows a directory
listing from the memory stick.
Signed-off-by: Simon Glass <sjg@chromium.org>