Commit Graph

40 Commits

Author SHA1 Message Date
pekon gupta
a7e36fc95f mtd: nand: omap: remove unused #defines from common omap_gpmc.h
OMAP NAND driver can detect Page-size and OOB-size of NAND device from ONFI
params or nand_id[] table. And based on that it defines ECC layout.
This patch
1) removes following board configs used for defining NAND ECC layout
	- GPMC_NAND_ECC_LP_x16_LAYOUT (for large page x16 NAND)
	- GPMC_NAND_ECC_LP_x8_LAYOUT  (for large page x8 NAND)
	- GPMC_NAND_ECC_SP_x16_LAYOUT (for small page x16 NAND)
	- GPMC_NAND_ECC_SP_x8_LAYOUT  (for small page x8 NAND)

2) removes unused #defines in common omap_gpmc.h depending on above configs

Build tested using: ./MAKEALL -s am33xx -s omap3 -s omap4 -s omap5

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-03-04 17:23:54 -06:00
Yegor Yefremov
6a1df37349 am3517_evm: activate Ethernet PHY
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2013-12-12 17:43:34 -05:00
Albert ARIBAUD
f15ea6e1d6 Merge branch 'u-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/armv7/rmobile/Makefile
	doc/README.scrapyard

Needed manual fix:
	arch/arm/cpu/armv7/omap-common/Makefile
	board/compulab/cm_t335/u-boot.lds
2013-12-10 22:23:59 +01:00
Tom Rini
18a02e8050 AM3517 EVM: Enable ethernet
Signed-off-by: Tom Rini <trini@ti.com>
2013-12-06 07:04:26 -05:00
Tom Rini
faca8ff55f Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2013-11-25 10:42:13 -05:00
pekon gupta
3f719069c8 mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme
This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed
CONFIG_xx used for selecting NAND ecc-schemes.
This patch aims at solving following issues.

1) Currently ecc-scheme is tied to SoC platform, which prevents user to select
   other ecc-schemes also supported in hardware. like;
 - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite
   the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with
   software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW).
 - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware
   supports BCH16 ecc-scheme also.

2) Different platforms use different CONFIG_xx to select ecc-schemes, which
   adds confusion for user while migrating platforms.
 - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only
    8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW)
    whereas ELM hardware engine supports other ecc-schemes also like; BCH4,
    and BCH16 (in future).
 - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error
    correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW).
 - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library

Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency
on SoC platform and NAND driver. And user can select ecc-scheme independently
foreach board.
However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still
depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-21 13:33:41 -06:00
Heiko Schocher
6789e84eca i2c, omap24xx: convert driver to new mutlibus/mutliadapter framework
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver

Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/

Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S  <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
2013-11-13 06:18:17 +01:00
Rob Herring
f232950f82 config: remove platform CONFIG_SYS_HZ definition part 2/2
Remove platform CONFIG_SYS_HZ definition for configs a-z*.

Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2013-11-04 11:06:16 -05:00
Lokesh Vutla
806d279247 ARM: OMAP: Add CONFIG_OMAP_COMMON
Adding a new CONFIG_OMAP_COMMON which is included by all boards
that needs to build cpu/armv7/omap-common folder.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2013-08-15 08:51:10 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Michael Jones
019be4af64 Remove unused CONFIG_SYS_I2C_BUS[_SELECT]
"CONFIG_SYS_I2C_BUS" and "CONFIG_SYS_I2C_BUS_SELECT" don't appear anywhere
outside of config files.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
2013-01-29 06:40:01 +01:00
Tom Rini
dfe161032d Merge branch 'master' of git://git.denx.de/u-boot-nand-flash 2012-11-26 14:53:33 -07:00
Scott Wood
6f2f01b9f3 spl/nand: introduce CONFIG_SPL_NAND_DRIVERS, _BASE, and _ECC.
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver.  Some SPLs need software ECC but others can't
fit it.

All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.

Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
2012-11-26 15:41:25 -06:00
Ilya Yanok
88919ff7bf am3517_evm: switch to musb-new
Use new musb framework instead of the old one on AM3517_EVM.

Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
2012-11-20 00:16:07 +01:00
Andrew Bradford
669681104d configs: Fix usage of mmc rescan
Fix usage of 'mmc rescan' by many configs.  Proper use is
'mmc dev ${mmcdev}; mmc rescan' to set the mmc device and then rescan
the device.  'mmc rescan' itself does not take any arguments.

Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
2012-10-23 08:33:17 -07:00
Tom Rini
47f7bcae8c SPL: Move the omap SPL framework to common/spl
Add a new flag, CONFIG_SPL_FRAMEWORK to opt into the common/spl SPL
framework, enable on all of the previously using boards.  We move the
spl_ymodem.c portion to common/ and spl_mmc.c to drivers/mmc/.  We leave
the NAND one in-place as we plan to replace it later in this series.

We use common/spl to avoid linker problems with respect to merging
constant strings in objects.   Otherwise all strings in common/ will be
linked in and kept which grows SPL in size too much.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Tom Rini
d7cb93b28a ARM: SPL: Move gpmc_init() to spl_board_init()
This is an OMAP/related-specific function, move calling it to
spl_board_init() and turn on CONFIG_SPL_BOARD_INIT on the boards that
enabled NAND and didn't enable this already.

Signed-off-by: Tom Rini <trini@ti.com>
2012-09-27 09:49:59 -07:00
Rob Herring
3d6ba91e79 ARM: Remove unused stack and irq config defines
CONFIG_STACKSIZE is not referenced anywhere except on AVR32, but present
in most ARM board config files.

IRQs are only enabled for 1 config, so remove the unused config options
for IRQ and FIQ stack size as well.

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-09-01 14:58:22 +02:00
Tom Rini
219f4788d3 hush.c: Move default CONFIG_SYS_PROMPT_HUSH_PS2 to hush.c
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2.  I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-06-20 20:36:51 +02:00
Joe Hershberger
806150063a net: Remove CMD_PING where there's no CMD_NET
Some boards claim to need ping, but don't support net.
That makes no sense, and causes problems now that ping
is in a separate file.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2012-05-23 14:19:22 -05:00
Tom Rini
e0820ccc38 ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
With older toolchains it is possible to not fit entirely into the 45KB
that we had assigned to SPL.  Adjust to allow for 8KB of stack (which
should be more than required) and 54KB of text/data.

Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Vaibhav Hiremath <hvaibhav@ti.com>
2012-05-15 08:31:41 +02:00
Tom Rini
1005ccfda4 include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
This define does not control anything, remove it.

Signed-off-by: Tom Rini <trini@ti.com>
2012-05-15 08:31:28 +02:00
Yegor Yefremov
10f3bdd36e am3517evm: remove rootfstype kernel parameter for MMC boot device
it is not necessary to define rootfstype for mass storage devices.
Kernel detects it automatically.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
2012-02-12 10:11:23 +01:00
Stefano Babic
d3022c5f5c nand_spl_simple: store ecc data on the stack
Currently nand_spl_simple puts it's temp data at 0x10000 offset in SDRAM
which is likely to contain already loaded data.
The patch saves the oob data and the ecc on the stack replacing
the fixed address in RAM.

Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Ilya Yanok <yanok@emcraft.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Simon Schwarz <simonschwarzcor@googlemail.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
2012-01-26 16:06:21 -06:00
Tom Rini
5059a2a471 AM3517: Add SPL support
The only change of note is that we move from 0x80008000 to 0x80100000
for CONFIG_SYS_TEXT_BASE

Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:39 +01:00
Thomas Weber
81dcf8bb11 ARM: OMAP: Remove STACKSIZE for IRQ and FIQ if unused
This patch removes the definition of stack sizes for
irq and fiq if the CONFIG_USE_IRQ is undefined before.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
2011-12-06 23:59:35 +01:00
Thomas Weber
0997561de9 ARM: OMAP3: Remove unused define SDRC_R_C_B
This patch removes the unused definition of SDRC_R_C_B
from the config files.

Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Acked-by: Tom Rini <trini@ti.com>
2011-12-06 23:59:35 +01:00
Joe Hershberger
b3f44c21ea common: cosmetic: CONFIG_BOOTFILE checkpatch compliance
Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
2011-10-22 01:21:35 +02:00
Vaibhav Hiremath
122e6e0a97 am3517evm: Use generic MMC driver
Switch from the legacy mmc driver to the
new generic mmc driver.

This patch is based on similar patch for beagle[1].

 [1] http://git.denx.de/?p=u-boot.git;a=commitdiff_plain;h=0cd31144240

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-04 11:36:17 +02:00
Christopher Harvey
75f980bdb3 Removed unused define, CONFIG_ARMV7.
Signed-off-by: Christopher Harvey <charvey@matrox.com>
2011-08-04 12:49:37 +02:00
Yegor Yefremov
49473adabf am3517evm: change console device from ttyS2 to ttyO2
the serial device names have been changed from ttySx to ttyOx, so the
console device name should be also changed to support the latest kernel
versions.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Vaibhav Hiremath<hvaibhav@ti.com>
2011-07-18 12:35:52 +02:00
Michael Jones
2cc195e0a5 Remove remnants of obsolete CONFIG_SYS_GBL_DATA_SIZE comments
commit 25ddd1fb0a left remnants of
many comments about CONFIG_SYS_GBL_DATA_SIZE.

Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
2011-05-12 23:04:55 +02:00
Luca Ceresoli
6cbec7b3ba ARMV7: OMAP3: Cleanup extern variables in mem.c
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.

Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-04-27 19:38:10 +02:00
Vaibhav Hiremath
aa82d5f2a6 AM3517:Build FIX: undef CONFIG_CMD_NFS support
Without CONFIG_CMD_NET support CONFIG_CMD_NFS leads
to linking error, so disable CONFIG_CMD_NFS option.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-29 16:36:07 -05:00
Vaibhav Hiremath
13acfc6f7f AM3517:Fix for ARM Relocation support
Also change the CONFIG_SYS_TEXT_BASE to 0x80008000, required
with relocation support. This is the load address for primary
boot loader (x-loader).

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-11-29 16:36:04 -05:00
Wolfgang Denk
25ddd1fb0a Replace CONFIG_SYS_GBL_DATA_SIZE by auto-generated value
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough.  This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool.  In the result, all definitions of this value can be
deleted from the board config files.  We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.

No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-26 21:05:30 +02:00
Ajay Kumar Gupta
7dc27b05a4 AM3517EVM: musb: add usb config
Enabling USB HOST in defconfig.

Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
2010-08-12 16:40:00 +02:00
Steve Sakoman
f56348af5d ARM: Rename arch/arm/cpu/arm_cortexa8 to armv7
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9

Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.

The two architectures are similar enough that substantial code can be shared.

Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-07-05 19:59:55 -04:00
Vaibhav Hiremath
1a5038ca68 AM35x: Add support for EMIF4
This patch adds support for the EMIF4 interface
available in the AM35x processors.

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08 10:07:19 -05:00
Vaibhav Hiremath
ed01e45cfa AM35x: Add support for AM3517EVM
This patch adds basic support for the AM3517EVM.
It includes:
	- Board files (.c and .h)
	- Default configuration file
	- Updates for Makefile

Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2010-06-08 10:07:18 -05:00