Commit Graph

1856 Commits

Author SHA1 Message Date
Wolfgang Denk
bd7bb6f8a3 Merge branch 'next' of git://git.denx.de/u-boot-nios 2010-05-28 20:34:39 +02:00
Thomas Chou
661ba14051 spi: add altera spi controller support
This patch adds the driver of altera spi controller, which is
used as epcs/spi flash controller. It also works with mmc_spi
driver.

This driver support more than one spi bus, with base list declared
#define CONFIG_SYS_ALTERA_SPI_LIST { BASE_0,BASE_1,... }

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-05-28 10:56:03 -04:00
Thomas Chou
3e6b86b555 misc: add gpio based status led driver
This patch adds a status led driver followed the GPIO access
conventions of Linux. The led mask is used to specify the gpio pin.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-05-28 10:56:03 -04:00
Andrew Caldwell
c941b77adc Blackfin: nand: drain the write buffer before returning
The current Blackfin nand write function fills up the write buffer but
returns before it has had a chance to drain.  On faster systems, this
isn't a problem as the operation finishes before the ECC registers are
read, but on slower systems the ECC may be incomplete when the core tries
to read it.

So wait for the buffer to drain once we're done writing to it.

Signed-off-by: Andrew Caldwell <Andrew.Caldwell@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-26 17:59:13 -05:00
Wolfgang Denk
c4976807cb Coding style cleanup, update CHANGELOG.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-26 23:51:22 +02:00
Wolfgang Denk
d74dda09f0 dm9000x.c: fix compile problems
Use readX() / writeX() accessors instead of inX() / outX().

Suggested-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-05-26 22:19:35 +02:00
Wolfgang Denk
8b79f2ce80 Merge branch 'master' of git://git.denx.de/u-boot-ubi 2010-05-21 22:26:14 +02:00
Wolfgang Denk
8a452c2c17 Merge branch 'master' of git://git.denx.de/u-boot-imx 2010-05-21 22:22:23 +02:00
Stefan Roese
1b1f9a9d00 UBI: Ensure that "background thread" operations are really executed
The current U-Boot UBI implementation is copied from Linux. In this
porting the UBI background thread was not handled correctly. Upon write
operations ubi_wl_flush() makes sure, that all queued operations, like
page-erase, are completed. But this is missing for read operations.

This patch now makes sure that such operations (like scrubbing upon
bit-flip errors) are not queued, but executed directly.

Signed-off-by: Stefan Roese <sr@denx.de>
2010-05-19 10:57:19 +02:00
Stefano Babic
03af5abd85 MX31: Added support for the Casio COM57H5M10XRC to QONG
The patch adds setup to connect a CASIO COM57H5M10XRC
(640x480 TFT display) to the QONG module.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-19 09:15:50 +02:00
Serge Ziryukin
a599cde769 lan91c96, smc911x: remove useless free(ptr) calls on NULL ptr
Signed-off-by: Serge Ziryukin <ftrvxmtrx@gmail.com>
2010-05-17 23:21:08 +02:00
Wolfgang Denk
1a1e6bf12b Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-05-17 23:11:21 +02:00
Wolfgang Denk
7b43db9211 drivers/mmc/fsl_esdhc.c: fix compiler warnings
Commit 77c1458d caused the following compiler warnings:

fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:142: warning: assignment discards qualifiers from pointer target type
fsl_esdhc.c: In function 'esdhc_setup_data':
fsl_esdhc.c:169: warning: unused variable 'wml_value'
fsl_esdhc.c: In function 'esdhc_pio_read_write':
fsl_esdhc.c:164: warning: control reaches end of non-void function

Fix these.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dipen Dudhat <dipen.dudhat@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
2010-05-15 19:47:17 +02:00
Kumar Gala
f54fe87ace 85xx/fsl-sata: Use is_serdes_configured() to determine if SATA is enabled
On the MPC85xx platform if we have SATA its connected on SERDES.
Determing if SATA is enabled via sata_initialize should not be board
specific and thus we move it out of the MPC8536DS board code.

Additionally, now that we have is_serdes_configured() we can determine
if the given SATA port is enabled and error out if its not in the
driver.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-12 04:53:51 -05:00
Wolfgang Denk
7b2afd9381 Merge branch 'master' of git://git.denx.de/u-boot-i2c 2010-05-06 23:21:00 +02:00
Ender.Dai
767fdc4af6 drivers/*/Makefile: fix conditional compile rule.
Fix conditional compile rule for twl4030.c and videomodes.c.

Signed-off-by: Ender.Dai <ender.dai@gmail.com>
2010-05-06 00:41:08 +02:00
Graeme Russ
167cdad137 SERIAL: Enable port-mapped access
The x86 architecture exclusively uses Port-Mapped I/O (inb/outb) to access
the 16550 UARTs. This patch mimics how Linux selects between Memory-Mapped
and Port-Mapped I/O. This allows x86 boards to use CONFIG_SERIAL_MUTLI and
drop the custom serial port driver

Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2010-05-06 00:16:28 +02:00
Mike Frysinger
b5cebb4fd6 Blackfin: TWI/I2C: implement multibus support
In order to do this cleanly, the register accesses have to be converted to
a C struct (base pointer), so do that in the process.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-05 10:04:38 +02:00
Stefano Babic
d205ddcfc5 SPI: added support for MX51 to mxc_spi
This patch add SPI support for the MX51 processor.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Stefano Babic
dfe5e14fa2 MX: RTC13783 uses general function to access PMIC
The RTC is part of the Freescale's PMIC controller.
Use general function to access to PMIC internal registers.

Signed-off-by: Stefano Babic <sbabic@denx.de>
Tested-by: Magnus Lilja <lilja.magnus@gmail.com>
2010-05-05 09:48:41 +02:00
Stefano Babic
28bb6d34d3 MX: Added Freescale Power Management Driver
The patch add supports for the Freescale's Power
Management Controller (known as Atlas) used together with i.MX31/51
processors. It was tested with a MC13783 (MX31) and
MC13892 (MX51).

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-05-05 09:48:41 +02:00
Wolfgang Denk
679ec15462 Merge branch 'master' of git://git.denx.de/u-boot-net 2010-05-04 22:57:37 +02:00
Mike Frysinger
4324dc72df Blackfin: bfin_mac: hook up new write_hwaddr function
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Thomas Chou
3ac9d6c650 net: ethoc: add write_hwaddr support
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Thomas Chou
6c7c444786 net: altera_tse: add write_hwaddr support
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:50 -07:00
Heiko Schocher
fb57ec97b9 net: fec_mxc: add write_hwaddr support
tested on the magnesium board.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Prafulla Wadaskar
b5ce63ed12 net:kirkwood_egiga.c: MAC addresses programming using write_hwaddr
Added a new function kwgbe_write_hwaddr for programming egiga
controller's hardware address.
This function will be called for each egiga port being used

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Thomas Chou
c960b13ed2 net: add altera triple speeds ethernet mac driver
This driver supports the Altera triple speeds 10/100/1000 ethernet
mac.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Thomas Chou
f6569884b4 net: add opencore 10/100 ethernet mac driver
This patch ports the opencore 10/100 ethernet mac driver ethoc.c
from linux kernel to u-boot.

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Valentin Yakovenkov
bd75db3feb smc911x driver frame alignment patch
SMSC911x chips have alignment function to allow frame payload data
(which comes after 14-bytes ethernet header) to be aligned at some
boundary when reading it from fifo (usually - 4 bytes boundary).
This is done by inserting fake zeros bytes BEFORE actual frame data when
reading from SMSC's fifo.
This function controlled by RX_CFG register. There are bits that
represents amount of fake bytes to be inserted.

Linux uses alignment of 4 bytes. Ethernet frame header is 14 bytes long,
so we need to add 2 fake bytes to get payload data aligned at 4-bytes
boundary.
Linux driver does this by adding IP_ALIGNMENT constant (defined at
skb.h) when calculating fifo data length. All network subsystem of Linux
uses this constant too when calculating different offsets.

But u-boot does not use any packet data alignment, so we don't need to
add anything when calculating fifo data length.
Moreover, driver zeros the RX_CFG register just one line up, so chip
does not insert any fake data at the beginig. So calculated data length
is always bigger by 1 word.

It seems that at almost every packet read we get an underflow condition
at fifo and possible corruption of data. Especially at continuous
transfers, such as tftp.

Just after removing this magic addition, I've got tftp transfer speed as
it aught to be at 100Mbps. It was really slow before.

It seems that fifo underflow occurs only when using byte packing on
32-bit blackfin bus (may be because of very small delay between reads).

Signed-off-by: Valentin Yakovenkov <yakovenkov@niistt.ru>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Prafulla Wadaskar
f0588fdf92 net: Kirkwood_egiga.c bugfixes for rx path
Cosmetic changes: Few comments updated
Functionality: Rx packet frame size is programming should
be done when port is in disabled state. this is corrected

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Eric Jarrige
2e236bf28e fec_mxc.c: Fix MX27 FEC MAC validity check
Fix MX27 FEC logic to check validity of the MAC address in fuse.
Only null (empty fuse) or invalid MAC address was retrieved from mx27 fuses before this change.

Signed-off-by:  Eric Jarrige <jorasse@armadeus.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:49 -07:00
Andy Fleming
538be58568 tsec: Wait for both RX and TX to stop
When gracefully stopping the controller, the driver was continuing if
*either* RX or TX had stopped.  We need to wait for both, or the
controller could get into an invalid state.

Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Mike Frysinger
a45dde2293 net: dm9000x: use standard I/O accessors
The current dm9000x driver accesses its memory mapped registers directly
instead of using the standard I/O accessors.  This can cause problems on
Blackfin systems as the accesses can get out of order.  So convert the
direct volatile dereferences to use the normal in/out macros.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel
5525856d59 mpc512x_fec: Move PHY initialization from probe into init routine.
This saves the autonegotation delay when not using ethernet in U-Boot

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
John Rigby
910119b3c4 fec_mxc don't use internal eeprom on MX25
Avoid using the internal eeprom on MX25 like MX51 already does.

Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Wolfgang Wegner
33f684d6d5 fix lockup in mcfmii/mii_discover_phy() in case communication fails
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Richard Retanubun
23c34af48f 83xx: UEC: Added support for bitBang MII driver access to PHYs
This patch enabled support for having PHYs on bitBang MII and uec MII
operating at the same time. Modeled after the MPC8360ADS implementation.

Added the ability to specify which ethernet interfaces have bitbang SMI
on the board header file.

Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Detlev Zundel
6f5f89f011 Remove unused "local_crc32" function.
For code archeologists, this is a nice example of copy and paste history.

Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:48 -07:00
Prafulla Wadaskar
e3f2a93362 net: Kirkwood_egiga.c: fixed build warnings
This patch fixes following build warnings for kirkwood_egiga.c

kirkwood_egiga.c: In function "kwgbe_init":
kirkwood_egiga.c:448: warning: dereferencing type-punned pointer will break strict-aliasing rules
kirkwood_egiga.c: In function "kwgbe_recv":
kirkwood_egiga.c:609: warning: dereferencing type-punned pointer will break strict-aliasing rules

Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-05-03 14:52:47 -07:00
Stefano Babic
7d27cd08b4 MX31: add accessor function to get a gpio
The patch adds an accessor function to get the value of a gpio.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-30 05:23:25 -05:00
Minkyu Kang
3bb6b037e8 SAMSUNG: make s5p common gpio functions
Because of s5pc1xx gpio is same as s5p seires SoC,
move gpio functions to drvier/gpio/
and modify structure's name from s5pc1xx_ to s5p_.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-30 05:23:23 -05:00
Minkyu Kang
46a3b5c8df SAMSUNG: serial: modify name from s5pc1xx to s5p
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.

Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
2010-04-30 05:23:23 -05:00
Stefano Babic
7c8cf0d0c7 MX31: Added LCD support for QONG module
Added support for LCD and splash image to the QONG module.
The supported display is VBEST-VGG322403.

Signed-off-by: Stefano Babic <sbabic@denx.de>
2010-04-27 23:13:37 +02:00
Wolfgang Denk
c303176aa0 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2010-04-27 22:57:41 +02:00
Wolfgang Denk
c88d6ab19f Merge branch 'next' of git://git.denx.de/u-boot-nios 2010-04-27 22:53:04 +02:00
Dave Liu
cd3abcfa2d fsl_sata: Move the snoop bit to another place
For P1022 SATA host controller, the data snoop bit of DW3 in PRDT
is moved to bit28.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:54 -05:00
Dave Liu
e4773debb7 fsl_sata: Add the workaround for errata SATA-A001
After power on, the SATA host controller of P1022 Rev1 is configured
in legacy mode instead of the expected enterprise mode.

Software needs to clear bit[28] of HControl register to change to
enterprise mode after bringing the host offline.

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:54 -05:00
Thomas Chou
994852966d altera_jtag_uart: bypass when no jtag connection
This patch adds an option to bypass output waiting when there
is no jtag connection. This allows the jtag uart work similar
to a serial uart, ie, boot even without connection.

This option is enabled with CONFIG_ALTERA_JTAG_UART_BYPASS

Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
2010-04-24 18:21:23 -04:00
Anatolij Gustschin
fbb0030e38 serial: struct serial_device: add uninit() entry for drivers
Subsequent patch extends mpc512x serial driver to support
multiple PSC ports. The driver will provide an uninit()
function to stop the serial controller and to disable the
controller's clock. Adding uninit() entry to struct serial_device
allows disabling the serial controller after usage of
a stdio serial device.

This patch adds uninit() entry to the struct serial_device
and fixes initialization of this structure in the code
accordingly.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
2010-04-24 21:34:07 +02:00