Crashes rarely happen in the CPLB miss handler compared to the rest of
U-Boot code, so disable hardware tracing when processing misses. This
way a crash due to other functions will be shown properly.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The new board revision has a different LCD.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If the requested clock cannot be exactly obtained, round it up so that we
err on the side of slightly slower rather than slightly faster.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some common code uses more of the io.h funcs than we currently provide, so
pull in all of the ones from the linux kernel.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
These need to be rethought, but until that happens, isolate the hack so
that we can extend the common code without breaking things.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Give the CF/IDE code its own file to keep things cleanly separated. While
we're here, clean up the code to use common functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some SPI devices like to see high idle values rather than low.
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The single initcode function was growing unwieldy, so split it up the
distinct steps into their own function. This should making digesting the
result much easier on people.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
While the initdram() function makes sense on some arches, it doesn't for
Blackfin systems as it's always implemented the same way.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The length of the sections is fixed at link time, so let the linker do the
calculation rather than doing it ourselves at runtime.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Very little additional code overhead, and only works when the user sets an
env var ahead of time, so default to on makes sense.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The tinyboards like to run at a little lower voltage than the default, and
they prefer to boot over the network. For the latter, extend the common
code a little to make this easier.
Also fix the cm-bf527 env sector size while we're in here to reflect the
flash that is actually in use.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the common config option for extracting the environment for embedding
into LDR files and clarify the LDR-specific option.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When malloc() was called before it was properly initialized
(as would happen if when used before relocation to RAM) it returned
random, non-NULL values, which called all kinds of difficult to debug
subsequent errors.
Make sure to return NULL when initialization was not done yet.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Support for LZARI compression mode was added based on a MTD CVS
snapshot of March 13, 2005. However, fs/jffs2/compr_lzari.c contains
contradictory licensing terms: the original copyright clause says "All
rights reserved. Permission granted for non-commercial use.", but
later reference to the file 'LICENCE' in the jffs2 directory was added
which says GPL v2 or later.
As no boards ever used LZARI compression, and this file is also not
present in recent MTD code, we resolve this conflict by removing the
conflicting file and references to it.
Also copy the referenced but missing file 'LICENCE' from the current
MTD source tree.
Signed-off-by: Wolfgang Denk <wd@denx.de>
For MUSB devices that do not support multipoint (hubs), we have to emulate
a root hub so that we can support core operations like resetting ports.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Adds required definitions for EHCI support in sequoia configuration file.
But still keeps the OHCI as default driver.
Signed-off-by: Chris Zhang <chris@seamicro.com>
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
controller must terminate the reset and stabilize the state of the port within
2 milliseconds". Without termination, a port stays at reset state. This is
observed on ppc4xx(sequoia) boards.
Signed-off-by: Chris Zhang <chris@seamicro.com>
This patch fixes this warning during compile:
omap3.c: In function 'musb_platform_init':
omap3.c:126: warning: label 'end' defined but not used
Problem reported by: Dirk Behme[dirk.behme@googlemail.com]
Signed-off-by: Sanjeev Premi <premi@ti.com>
The RX Control/Status register has bits that we want to preserve, so don't
just write out a single bit. Preserve the others bits in the process.
The original code posted to the u-boot list had this behavior, but looks
like it was lost somewhere along the way to merging.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The multipoint handling under MUSB is optional, and some parts (like the
Blackfin processor) do not implement support for it.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The dynamic FIFO handling under MUSB is optional, and some parts (like
the Blackfin processor) do not implement support for it.
Due to this, the FIFO reading/writing steps need special handling, so
mark the common versions weak so drivers can override.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Adding USB configuration. Default is set for USB MSC host.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Added DA8xx GPIO base addresses in gpio_defs.h and pointers
to different BANKs which can be used to program GPIOs.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
USB0_DRVVBUS pinmux configuration is required for USB functinality
in uboot.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Swaminathan S <swami.iyer@ti.com>
Add support to configure bus parking mode and master in bus arbitration
configuration (ACR). Add this for the kmeter1 port:
Configure bus arbiter with recommended values from Freescale
to improve bus latency/throughput for application with
intensive QuiccEngine activity.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Remove PCI reset, if there is a monarch PMC module.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
convert clrbits_be32 + setbits_be32 to clrsetbits_be32, use out_be32 to set gcr.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The caddy2 is a variant of the already supported vme8349. So we just
add the differences to this board port. To better support those two
boards we switched from fixed SDRAM configuration to usage of
spd_sdram(). This is done by providing a board specific SPD EEPROM
routine with different values for both boards.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
changed to use mkconfig -t option instead, plus misc codingstyle fixes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The memory controller could already be enabled, when spd_sdram() is
called. This could be the case for example, when the SDRAM is initialized
by the JTAG debugger.
The "sync" after the register access via the accessor function is
still needed, because the macro uses the sync before the real write
is done. So until not all accesses are converted to using accessor
functions, this sync still needs to be made "manually" here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd.eu>
Acked-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
