Sync with 14e21cb8f811 ("arm64: dt: hikey: Add optee node"
from Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
This allows to boot all STM32F7 and STM32H7 boards independently
of the amount of embedded SDRAM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences. With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)
Signed-off-by: Adam Ford <aford173@gmail.com>
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone. This cleans up
this unnneeded stuff.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device tree entries are from linux-omap's for-next branch
destined to me put into 4.20 (or whatever the version is after 4.19)
Signed-off-by: Adam Ford <aford173@gmail.com>
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbt0FOAAoJECaAFcEOcohNZmcH/A1mKO0/R4tHCqFP2j0I+OuP
PClkA1HUZuD5phvPMaxdHQBwsq7sAa8AljK1oPCNkslP7mFxToUUBx7xc0vB89P/
D+XsI4uce89hIyTULR2FdhR22MOk41zaLVeNicpQ1keCNbzCwsHsHTA+B4XN/xNe
tdPpu6wN2D+g88DAv+/ebVYgjmxRvFD4qpL9bbZpOqqA8XCcD31ukCR2E4fsESgn
mzwKaKcX6SeYgTVCT8Q15SLTNI1WRUY1Y1laj1WKl4abY+HsTt4Whm9imM2l3K5W
ODj6vnFlwEC9rgdxmtXGcmBfwtyXubSfuZDrMGFAiOlyIUgpPXWZI7i8LYQbZ7s=
=NdBl
-----END PGP SIGNATURE-----
Merge tag 'rockchip-for-v2018.11-rc2' of git://git.denx.de/u-boot-rockchip
Rockchip-focused changes for v2018.11-rc2:
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
Signed-off-by: Tom Rini <trini@konsulko.com>
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
[1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit
[2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Even though arc-linux- prefix is used in ARC prebuilt tools and
in Buildroot there're other options like Linux distro cross-tools
etc where prefix is different so let's not rely on this default.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
make_fit_atf.py uses physical address of first segment as the
entry point to bl31. It is incorrect and causes following abort
when bl31_entry() is called:
U-Boot SPL board initTrying to boot from MMC1
"Synchronous Abort" handler, esr 0x02000000
elr: 0000000000000000 lr : 00000000ff8c7e8c
x 0: 00000000ff8e0000 x 1: 0000000000000000
x 2: 0000000000000000 x 3: 00000000ff8e0180
x 4: 0000000000000000 x 5: 0000000000000000
x 6: 0000000000000030 x 7: 00000000ff8e0188
x 8: 00000000000001e0 x 9: 0000000000000000
x10: 000000000007fcdc x11: 00000000002881b8
x12: 00000000000001a2 x13: 0000000000000198
x14: 000000000007fdcc x15: 00000000002881b8
x16: 00000000003c0724 x17: 00000000003c0718
x18: 000000000007fe80 x19: 00000000ff8e0000
x20: 0000000000200000 x21: 00000000ff8e0000
x22: 0000000000000000 x23: 000000000007fe30
x24: 00000000ff8d1c3c x25: 00000000ff8d5000
x26: 00000000deadbeef x27: 00000000000004a0
x28: 000000000000009c x29: 000000000007fd90
Fix it by using the entry point from the elf header.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We package U-Boot and OP-TEE into one itb file for SPL,
so that we can support OP-TEE in SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Patch fix warning:
/builddir/BUILD/u-boot-2018.05-rc2/"arch/arm/mach-rockchip/make_fit_atf.py" \
arch/arm/dts/rk3399-firefly.dtb > u-boot.its
./tools/mkimage -f u-boot.its -E u-boot.itb >/dev/null && cat
/dev/null
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@2 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@3 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node
/configurations/config@1 has a unit name, but no reg property
make[1]: Leaving directory
'/builddir/BUILD/u-boot-2018.05-rc2/builds/firefly-rk3399'
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Additional sgmii phymode is added in socfpga_phymode_setup() along with
a minor fix for maximum number of GMACs.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Enable PHY framework on Gen3, this is required for USB EHCI PHY support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark area 0x1_0000_0000 - 0x10_0000_0000 as DRAM on Gen3 as the
chip is capable of addressing that and U-Boot can make use of it.
This patch prevents exception when accessing those areas.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The I2C6 is used to communicate with the PMIC and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If environment variable CROSS_COMPILE is not set, this indicates native
compilation. In this case we should not set an arbitrary value which is
not applicable for 64bit anyway.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The Sentence "reset unsupported yet" is not
grammatically correct and should say
"reset not supported yet" instead.
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Rick Chen <rick@andestech.com>
We don't have a reset method on any RISC-V board yet. Instead of
adding the same 'unsupported' message for each CPU variant it might
make more sense to add a generic do_reset function for all CPU
variants to lib/, similar to the one for ARM (arch/arm/lib/reset.c).
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This implies DM support for some common drivers that are used on
RISC-V.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
RISC-V is a pretty new architecture and should support DM and
OF_CONTROL by default.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
There are quite a lot of mixed tabs and spaces in the ae350.dts.
Clean them up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Currently start.S is inside arch/riscv/cpu/ax25/, but it can be
common for all RISC-V targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
So far this is hardcoded to zero, and we should read the value from
mhartid CSR and pass it to Linux kernel.
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
There is no reason to keep two versions of CSR read/write defines
in encoding.h. We already have one set of defines in csr.h, which
is from Linux kernel, and let's drop the one in encoding.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
This adds a helper routine to print CPU information. Currently
it prints all the instruction set extensions that the processor
core supports.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
At present the compiler flag against which architecture and abi
variant the riscv image is built for is not explicitly indicated
which means the default compiler configuration is used. But this
does not work if we want to build a different target (eg: 32-bit
riscv images using a toolchain configured for 64-bit riscv).
Fix this by explicitly passing -march and -mabi to the compiler.
Since generically we don't use floating point in U-Boot, specify
the RV[32|64]IMA ISA and software floating ABI.
This also fix some alignment coding style issues.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
There are several coding style issues in the linker script. Fix them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The linker script can be shared by all RISC-V targets. Move it to
a common place.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The first argument of Linux kernel is the risc-v core hart id,
from which the kernel is booted from. It is not the mach_id,
which seems to be copied from arm.
While we are here, this also changes the Linux kernel entry
parameters' type to support both 32-bit and 64-bit.
Note the hart id is hardcoded to zero for now, and we should
change to fill in it with the value read from mhartid CSR of
the hart which this routine is currently running on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
This was copied from ARM, and does not apply to RISC-V. While we
are here, bootm.h is eventually removed as its content is only
the inclusion of setup.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
It's RISC-V that is the official name, not RISCV.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
[picked from the identical linux patch
https://patchwork.kernel.org/patch/10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.
While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add a test which verifies that all subnodes under "/firmware"
nodes are scanned.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed
ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile,
updated #if condition in drivers/firmware/firmware-uclass.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
