Some phys (Micrel) has extended registers that must be
accessed in a special way. Add pointers to the phy driver
structure to allow to use these functions with mdio command.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Since commit c2dd0d455 and 45bf05854 introduced
the new cache maintainance framework to ARM,
CONFIG_L2_OFF has not been used at all.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The physical base address of the NOR flash is 0x1e000000
on the Malta boards. The hardware also maps the first 4MiB
of the flash into the 0x1fc00000-0x1fffffff range.
Currently, U-Boot uses the mapped address to access the
flash, which does not work in recent qemu versions.
Since commit a427338b222b43197c2776cbc996936df0302f51
(mips_malta: correct reading MIPS revision at 0x1fc00010)
writing to the mapped address space causes a CPU exception.
Due to the exception, U-Boot hangs during boot when it tries
to detect the CFI flash chip.
Use the correct physical address for the MALTA_FLASH_BASE
constant to fix the problem. In order to avoid relocation
problems, also update the CONFIG_SYS_{TEXT,MONITOR}_BASE
constants.
The change makes it possible to start U-Boot on a Malta
board emulated with Qemu 1.6.1 and 1.7.0-rc0. It also
works on older versions (tested with 1.1.1, 1.2.2, 1.4.2,
1.5.3).
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
T1042RDB_PI is Freescale Reference Design Board supporting the T1042
QorIQ Power Architecture™ processor. T1042 is a reduced personality
of T1040 SoC without Integrated 8-port Gigabit. The board is designed
with low power features targeted for Printing Image Market.
T1042RDB_PI is similar to T1040RDB board with few differences like
it has video interface, supports T1042 personality
T1042RDB_PI board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Two on-board RGMII 10/100/1G ethernet ports.
- SERDES Connections, 8 lanes supporting:
— PCI
— SATA 2.0
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 1GB 8-bit NAND flash
- NOR: 128MB 16-bit NOR Flash
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- CPLD
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Video
- DIU supports video at up to 1280x1024x32bpp
- HDMI connector
- Power Supplies
- USB
- Supports two USB 2.0 ports with integrated PHYs
- Two type A ports with 5V@1.5A per port.
- SDHC
- SDHC/SDXC connector
- SPI
- On-board 64MB SPI flash
- I2C
- Device connected: EEPROM, thermal monitor, VID controller, RTC
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Use a default RCW of protocol 0x66.
A PBI configure file which uses CPC as 256KB SRAM. It can be used by
PBL tool on T1040 to build a pbl boot image.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
- add zync i2c driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Michal Simek <michal.simek@xilinx.com>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
This updates to new I2C framwwork on sh_i2c.
And this also updates boards(kzm9g and ecovec) that using sh_i2c.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use scf0403 driver to add scf0403x LCD support for cm-t35 and cm-t3730
boards.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The flag combination "SPI_XFER_BEGIN | SPI_XFER_END" is a common use
case of spi_xfer, and it can easily cause an already long line (spi_xfer
takes 5 parameters) to go over the 80 character limit.
define SPI_XFER_ONCE to be a shorter version of the above flag combination.
Cc: Tom Rini <trini@ti.com>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Current implementation only supports 8 bit word lengths, even though
omap3 can handle anything between 4 and 32.
Update the spi interface to support changing the SPI word length,
and implement it in omap3_spi driver to support the full range of
possible word lengths.
This implementation is backwards compatible by defaulting to the old
behavior of 8 bit word lengths.
Also, it required a change to the omap3_spi non static I/O functions,
but since they are not used anywhere else, no collateral changes are required.
Cc: Tom Rini <trini@ti.com>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
The MPC824x processors have long reached EOL, and the PN62 board has
not seen any board-specific updates for more than a decade. It is now
causing build issues. Instead of wasting time on things nobody is
interested in any more, we rather drop this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
cc: Tom Rini <trini@ti.com>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
The memsize environment variable must contain the
memory size in bytes on the Malta board. Otherwise
Linux will use wrong memory size which causes a kernel
panic.
Define CONFIG_MEMSIZE_IN_BYTES in malta.h to avoid
that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Allow the environment to be stored in the monitor flash of a Malta
board. The environment is stored in the final 128KB of the flash, which
both leaves the majority of the flash available for U-boot code and also
matches the location which YAMON uses.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is actually required in order for a Linux kernel to boot
successfully on a physical Malta board. Without enabling the RTC, a
Malta Linux kernel will get stuck in its estimate_frequencies function
on boot.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
These will now be detected at runtime, allowing a single U-boot
configuration to function correctly with different bitstreams. Without
this you may need to re-configure, re-build and re-flash U-boot to your
Malta if you flash a new bitstream with a different cache configuration
to your old bitstream.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This model of the pcnet is used in current Malta boards, at least in the
Malta-R rev 3. Enable support for it.
The Malta also has the ethernet controller PROM containing its MAC
address, so enable support for that in order to read that MAC address.
DHCP is a very useful feature to have available for many networks,
enable support for it also.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.
Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.
Tested on:
- A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
with and without an L2 cache.
- QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch simply #ifdef's out the C-specific parts of pci.h when it is
included by an assembly file. This will allow the macros it contains to
be used from assembly source as will be done in a followup commit adding
support for more modern MIPS Malta boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.
Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.
Changes v2:
- add a note to the README
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.
Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h
Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
This patch prevents:
- ums disk capacity miscalculation because of integer overflow
Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Commit 1b0757e deleted the EP88x entry from boards.cfg file.
But it missed to remove include/configs/EP88x.h and board/ep88x/.
This commit removes them and adds EP88x to README.scrapyard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
The malloc space is to small to boot, the current uboot 2013.10-rcX,
This will fix the startup problems by increasing the mallog space to 4MiB.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Since more functions are enabled, the eb_cpux9k2_ram target does not boot.
This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
