On ZeBu emulator, CAS to preamble overrides need to be set to
satisfy the timing. This only impact platforms with CONFIG_EMU.
These should be set before MEM_EN is set.
Signed-off-by: York Sun <yorksun@freescale.com>
When booting from USB peripheral boot, the bootrom will not properly deinit the
MUSB controller, which doesn't clearly indicate an USB disconnection to the host
and leaves U-Boot to deal with the state of the previous USB session.
On some host controller drivers (e.g. xhci_hcd), this ends up in a failure
during set address, caused by the lack of proper disconnection notification.
Resetting the controller early in U-Boot notifies the host of the disconnection
and doesn't hurt other use cases.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
The dwc3_set_mode function is used only in
drivers/usb/host/xhci-exynos5.c so make it to static.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Fix bus width switching from 8-bit mode down to 4-bit or 1-bit modes on
Samsung SoCs using SDHCI_QUIRK_USE_WIDE8. These SoCs report controller
version 2.0 yet they support 8-bit bus widths. If 8-bit mode was
previously enabled and then an operation like "mmc dev" caused a switch
back down to 4-bit or 1-bit mode, WIDE8 was left set, causing failures.
This problem was manifested by "mmc dev" timing out.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Depending on the boot priority, the eMMC/SD cards,
can be initialized with the same numbers for each boot.
To be sure which mmc device is SD and which is eMMC,
this info is printed by 'mmc list' command, when
the init is done.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Before this commit, the mmc devices were always registered
in the same order. So dwmmc channel 0 was registered as mmc 0,
channel 1 as mmc 1, etc.
In case of possibility to boot from more then one device,
the CONFIG_SYS_MMC_ENV_DEV should always point to right mmc device.
This can be achieved by init boot device as first, so it will be
always registered as mmc 0. Thanks to this, the 'saveenv' command
will work fine for all mmc boot devices.
Exynos based boards usually uses mmc host channels configuration:
- 0, or 0+1 for 8 bit - as a default boot device (usually eMMC)
- 2 for 4bit - as an optional boot device (usually SD card slot)
And usually the boot order is defined by OM pin configuration,
which can be changed in a few ways, eg.
- Odroid U3 - eMMC card insertion -> first boot from eMMC
- Odroid X2/XU3 - boot priority jumper
By this commit, Exynos dwmmc driver will check the OM pin configuration,
and then try to init the boot device and register it as mmc 0.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this
capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13
tablet, so always set it thereby fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Clksel value is exynos specific value.
It removed "clksel_val" into dwmci_host and created the
"dwmci_exynos_priv_data" structure for exynos specific data.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
"clksel_val" is assigned to property of mmc or defined value.
But it doesn't write at initial sequence.
There is a reason that get the wrong source-clock value.
This patch fixed it.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Some boards cannot do voltage negotiation but need to set the VSELECT
bit forcely to ensure it to work at 1.8V.
This commit adds CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT flag for this use.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds support to switch to 1.8V in case CMD11 succeeds.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Marek Vasut <marex@denx.de>
Sending out 5V when there is a charger connected to the otg port is not a
good idea, so check for this and error out.
Note this commit currently breaks otg support on the q8h tablets, as we need
to do some magic with the pmic there to get vbus info, this is deliberate
(better safe then sorry), fixing this is on my TODO list.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
High Capacity (e)MMC cards work fine on sun4i / sun5i, and not having this
capability set causes u-boot to not recognize the eMMC on an Utoo P66 A13
tablet, so always set it thereby fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the 6" 480x800 tl059wv5c0 panel used on e.g. Utoo P66 and
Aigo M60/M608/M606 tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On some boards there is a gpio to reset the LCD panel, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add debug UART functions to permit ns16550 to provide an early debug UART.
Try to avoid using the stack so that this can be called from assembler before
a stack is set up (at least on ARM and PowerPC).
Signed-off-by: Simon Glass <sjg@chromium.org>
For the debug UART we need to be able to provide any parameters before
driver model is set up. Add parameters to the low-level access functions
to make this possible.
Signed-off-by: Simon Glass <sjg@chromium.org>
This came up in a discussion on the mailing list here:
https://patchwork.ozlabs.org/patch/384613/
My concerns at the time were:
- it doesn't need to be written in assembler
- it doesn't need to be ARM-specific
This patch provides a possible alternative. It works by allowing any serial
driver to export one init function and provide a putc() function. These
can be used to output debug data before the real serial driver is available.
This implementation does not depend on driver model, and it is possible for
it to operate without a stack on some architectures (e.g. PowerPC, ARM). It
provides the same features as the ARM-specific debug.S but with more UART
and architecture support.
Signed-off-by: Simon Glass <sjg@chromium.org>
Make this option available in Kconfig and clean up the board that uses it.
Note there is also an entry in exynos5-common.h but this affects multiple
boards and should be dropped as part of the Samsung I2C migration to
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since both I2C and SPI are converted to Kconfig, we can convert cros_ec
to Kconfig for these buses.
LPC will need to wait until driver mode PCI is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
PCI specification allow prefetchable memory to be 32-bit or 64-bit.
PCI express specification states that all memmory bars for prefetchable
memory must be implemented as 64-bit. They all require that 64 bit
prefetchble memory are suported especially when u-boot is ported to
more and more 64bit processors.
Signed-off-by: David Feng <fenghua@phytium.com.cn>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Peripheral mode needs us to signal vusb high to the phy for it to work,
just like the host mode does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Only use CONFIG_SUNXI_MAX_FB_SIZE to reserve memory at the top when relocating
u-boot, and calculate the actual amount of memory necessary when setting up
the video-mode and use only that, freeing up some additional memory for use
by the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Do not use CONFIG_SYS_MEM_TOP_HIDE for the framebuffer, instead override
board_get_usable_ram_top to make sure that u-boot is not relocated into the
area where we want to use the framebuffer, and patch the devicetree from
sunxi_simplefb_setup() to tell the kernel to not touch the framebuffer.
This makes u-boot properly see the framebuffer as dram, and initalize the
level 2 cache for it, fixing the very slow cfb scrolling problem.
As an added bonus this stops us from reserving the framebuffer when simplefb
is not used because an older kernel is booted, or hdp is used and no hdmi
cable was plugged in, freeing up the memory for kernel use in these cases.
Reported-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On Keystone2 devices serdes must be initialized before accessing MDIO bus.
This commit moves the keystone2_net_serdes_setup() from keystone2_eth_open
to keystone2_emac_initialize to meet that requirement.
This also eliminates unnecessary serdes initializatin every time when the
keystone2_eth_open is being called.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Nishanth Menon <nm@ti.com>
The patch c316f577b4 breaks
siemens boards because prefetch mode is not enabled.
I assume it breaks other boards as well that don't use
prefetch.
This patch sets read_buf to nand_read_buf if
NAND_OMAP_GPMC_PREFETCH is not defined.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
CC: Daniel Mack <zonque@gmail.com>
CC: Guido Martínez <guido@vanguardiasur.com.ar>
CC: Tom Rini <trini@ti.com>
CC: Heiko Schocher <hs@denx.de>
Targets with CONFIG_NEEDS_MANUAL_RELOC do not use REL/RELA
relocation (mostly only GOT) where functions aray are not
updated. This patch is fixing function pointers for DM core
and serial-uclass to ensure that relocated functions are called.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch add DT support for mxc gpio driver.
There are one place using CONFIG_OF_CONTROL macro.
1. The U_BOOT_DEVICES and mxc_plat array are complied out. To DT,
platdata is alloced using calloc, so there is no need to use mxc_plat.
The following situations are tested, and all work fine:
1. with DM, without DT
2. with DM and DT
3. without DM
Since device tree has not been upstreamed, if want to test this patch.
The followings need to be done.
+ pieces of code does not gpio_request when using gpio_direction_xxx and
etc, need to request gpio.
+ move the gpio settings from board_early_init_f to board_init
+ define CONFIG_DM ,CONFIG_DM_GPIO and CONFIG_OF_CONTROL
+ Add device tree file and do related configuration in
`make ARCH=arm menuconfig`
These will be done in future patches by step.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
Add a new entry in platdata structure and intialize
bank_index in mxc_plat array.
This new entry can avoid using `plat - mxc_plat` by using
`plat->bank_index`.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
Abstracting dev_get_addr can improve drivers that want to
get device's address.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Simon Glass <sjg@chromium.org>
This adds driver model support with this driver. This was tested by Koelsch
board and Gose board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Simon Glass <sjg@chromium.org>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Make the driver model I2C API available always, even if driver model
is not enabled. This allows for a 'soft' switch-over, where drivers can
use the new structures in code which is compiled but not yet used. This
makes migration easier in some cases.
Fix up the existing drivers which define their own 'struct i2c_msg'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
As with i2c_read() and i2c_write(), add a dm_ prefix to the driver model
versions of these functions to avoid conflicts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
This uses the ns16550 driver but sets up the clock at run-time. It does
not seem to be available in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
If no device is connected to I2C bus, the i2c probe command
can take a lot of time for probe each address. This commit
reduces the busy timeout to 10ms for standard and high speed
modes. This doesn't break the transmission an also allow for
properly probe the devices.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Changes v3:
- new commit, after split the next one
Tested-by: Simon Glass <sjg@chromium.org>
Use dev_get_priv() rather than dev_get_platdata() to get correct address of
private data.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reduce the lcd_display_bitmap #ifdef complexity by extracting Atmel-specific
code for setting cmap for bitmap images into a new function lcd_set_cmap().
A default version is implemented with the remainder of the code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reduce the bitmap_plot #ifdef complexity by extracting MPC823-specific code for
setting cmap into its own implementation of lcd_logo_set_cmap(), implemented in
mpc8xx_lcd.c. In the MPC823 implementation, ARRAY_SIZE(bmp_logo_palette) is
switched for BMP_LOGO_COLORS to avoid having to include bmp_logo_data.h, which
would cause a compilation error because the logo data and palette arrays would
be defined twice.
This is a step towards cleaning bitmap_plot() of platform-specific code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reduce the bitmap_plot #ifdef complexity by extracting Atmel-specific code for
setting cmap into a new function lcd_logo_set_cmap(), which is implemented in
atmel_lcdfb driver and defined as part of common/lcd.c api with a weak dummy
version. In the Atmel implementation, ARRAY_SIZE(bmp_logo_palette) is
switched for BMP_LOGO_COLORS to avoid having to include bmp_logo_data.h, which
would cause a compilation error because the logo data and palette arrays would
be defined twice.
This is a step towards cleaning bitmap_plot() of platform-specific code.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reduce the amount of platform-specific code in common/lcd.c by moving MPC823
implementation of fb_put_byte() to mpc8xx_lcd.c. Since we must also have a
default implementation for everybody else, make the remainder of the code
into a weak function.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reduce the amount of platform-specific code in common/lcd.c by moving Atmel
implementation of fb_put_word() to atmel_lcdfb.c. Since we must also have a
default implementation for everybody else, make the remainder of the code
into a weak function.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
configuration_get_cmap() is multiple platform-specific functions stuffed into
one function. Split it into multiple versions, and move each version to the
appropriate driver to reduce the #ifdef complexity.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
As the PMECC hardware has different version. In SAMA5D4 chip, the PMECC ip
can generate 0xff pmecc ECC value for all 0xff sector.
According to this, add PMECC version check, if it's SAMA5D4 then we always
let PMECC hardware to correct it.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The base address is found in a different way and the protection bit is also
in a different place. Otherwise it is very similar.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since these board functions seem to be the same for all boards which use
FSP, move them into a common file. We can adjust this later if future FSPs
need more flexibility.
This creates a generic PCI MMC device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds the DDR3 setup and training code taken from the Marvell
U-Boot repository. This code used to be included as a binary (bin_hdr)
into the AXP boot image. Not linked with the main U-Boot. With this code
addition and the following serdes/PHY setup code, the Armada-XP support
in mainline U-Boot is finally self-contained. So the complete image
for booting can be built from mainline U-Boot. Without any additional
external inclusion. Hopefully other MVEBU SoC's will follow here.
Support for some SoC's has been removed in this version. This is:
MV_MSYS:
The code referred to by the MV_MSYS define is currently unused. And its
not really planned to support this in mainline. So lets remove it to
make the code clearer and increase the readability.
MV88F68XX (A38x):
The code referred to by the MV88F68XX define (A38x) is currently unused.
And its partial and not sufficient for this device in this stage.
So lets remove it to make the code clearer and increase the readability.
MV88F66XX (ALP):
The code referred to by the MV88F66XX define is currently unused. And its
not really planned to support this in mainline. So lets remove it to
make the code clearer and increase the readability.
MV88F78X60_Z1:
The code referred to by the MV88F78X60_Z1 define is currently unused. As the
Z1 revision of the AXP is not supported in mainline anymore.
So lets remove it to make the code clearer and increase the readability.
Remove support for Z1 & A0 AXP revisions (steppings). The current stepping
is B0 and this is the only one that is actively supported in this code
version.
Tested on AXP using a SPD DIMM setup on the Marvell DB-MV784MP-GP board and
on a custom fixed DDR configuration board (maxbcm).
Note:
This code has undergone many hours of coding-style cleanup and refactoring.
It still is not checkpatch clean though, I'm afraid. As the factoring of the
code has so many levels of indentation that many lines are longer than 80
chars. This might be some task to tackly later on.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Since we must run a PCI BIOS ROM, and this can take a calamitous amount of
time, measure it using bootstage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If the BIOS emulator is not available, allow use of native execution if
available, and vice versa. This can be controlled by the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a driver which locates the available XHCI controllers on the PCI bus
and makes them available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is an existing function prototype in the header file but it is not
implemented. Implement something similar.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This results in a much more readable callgraph, because now they
can't be confused with the function having exactly the same name
in the generic mmc code.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On both my A13-OLinuxIno and my A13-OLinuxIno-Micro, the vga output gives an
unstable image when active low v or hsync is used.
The problem seems to be specific to the OLinuxIno A13 (normal & micro)
boards. I've just looked up the schematics and they use an opendrain driver
for the vga sync lines, and with sync pulses it is the logical high->low
edge of the pulse which counts for the timing, which with an active low
sync is being driven by the pull-up, and that simply seems to not drive
it hard enough to get a stable image.
So force v and hsync active high on these boards. independent of what the
modeline says. This fixes the unstable image.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
If for some reason DMA module fails to reset user oserves only this:
--->---
# dhcp
Trying dwmac.e0018000
FAIL
--->---
This message makes not much sense.
With proposed change error message will be more helpful:
--->---
# dhcp
Trying dwmac.e0018000
DMA reset timeout
FAIL
--->---
For example user may do power toggle to recover board functionality.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a phy driver for the Micrel KSZ8895 switch. As the SoC MAC
is directly connected to the switch MAC the link to the switch is always up.
But the KSZ8895 switch can be hardwired in three configuration modes :
- not configurable with eventually an eeprom-stored configuration
- configurable by the mdio/mdc connection (SMI protocol)
- configurable by a SPI connection.
In not configurable mode, the switch starts automatically, but in the
other modes, it must be started programmatically, by writing 1 in
configuration register 1.
We only support the not configurable and mdio/mdc (aka SMI) modes here.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
If the PHY is not recognized don't access phydev (NULL)
and return 0 to signal failure.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Fix this:
drivers/pci/pci_rom.c:95:15: warning: cast to pointer from
integer of different size [-Wint-to-pointer-cast]
rom_header = (struct pci_rom_header *)rom_address;
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
These functions are useful in case the board calls them. Also fix a missing
parameter caused by applying the wrong patch (actually I failed to send v2
and applied v1 by mistake).
Signed-off-by: Simon Glass <sjg@chromium.org>
Since U-Boot can support different offset lengths (0-4 bytes), add a device
tree property to specify this. This avoids hard-coding it in the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adjusts the s3c24x0 driver to new i2c api
based on driver-model. The driver supports standard
and high-speed i2c as previous.
Tested on Trats2, Odroid U3, Arndale, Odroid XU3
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Tested-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch fixes build error for CONFIG_DM_I2C_COMPAT.
In i2c_get_chip_for_busnum() call, one of argument was missed,
which was offset_len. Now it is set to 'alen' as previous.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a new rsa uclass for performing modular exponentiation and implement
the software driver basing on this uclass.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
I2C is now deprecated on ARM platforms and there are no devices that use it
with the v3 protocol. We can't require v3 support if we want to support I2C.
Adjust the error handling to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
We don't want to bind devices which should never be used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we go through various contortions to store the I2C's chip
address in its private data. This only exists when the chip is active so
must be set up when it is probed. Until the device is probed we don't
actually record what address it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the address when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use struct spi_slave as our device pointer in a lot of places
to avoid changing the old SPI API. At some point this will go away.
But for now, it is better if the SPI uclass sets up this pointer, rather
than relying on passing it into the device when it is probed. We can use the
new uclass child_pre_probe() method to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some buses need to set up their devices before they can be used. This setup
may well be common to all buses in a particular uclass. Support a common
pre-probe method for the uclass, called before any bus devices are probed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For buses, after a child is bound, allow the uclass to perform some
processing. This can be used to figure out the address of the child (e.g.
the chip select for SPI slaves) so that it is ready to be probed.
This avoids bus drivers having to repeat the same process, which really
should be done by the uclass, since it is common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is common to all SPI drivers and specifies a structure used by the
uclass. It makes more sense to define it in the uclass.
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
In many cases the per-child private data for a device's children is defined
by the uclass rather than the individual driver. For example, a SPI bus
needs to store information about each of its children, but all SPI drivers
store the same information. It makes sense to allow the uclass to define
this data.
If the driver provides a size value for its per-child private data, then use
it. Failng that, fall back to that provided by the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
At present we try to use the 'reg' property and device tree aliases to give
devices a sequence number. The 'reg' property is often actually a memory
address, so the sequence numbers thus-obtained are not useful. It would be
better if the devices were just sequentially numbered in that case. In fact
neither I2C nor SPI use this feature, so drop it.
Some devices need us to look up an alias to number them within the uclass.
Add a flag to control this, so it is not done unless it is needed.
Adjust the tests to test this new behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>