This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Configure the pad setting and enable qspi clock to support qspi
flashes access.
Add QSPI related macro in configuration header file.
Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.
Let's get rid of get_board_rev() as it is not being used with its correct
meaning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Repair the register configuration and add proper support for the
display attached to both LVDS channels.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Pull all of the video handling into a separate file, since a lot
more code will be added and such code would polute the board file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Pull the definitions of GPIOs into a separate header file, so that
they can be used across all source files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Just zap multiple spaces and replace them with tabs properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Create a fake model table entry with default values, so we can error
check the board rev value once when querying it from the firmware, rather
than error-checking for invalid board rev values every time the model
table is used.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add a board rev entry for the new model A+, and augment the board
rev error handling code to be a bit more verbose.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Model A and CM RPis don't have an on-board USB Ethernet device. Hence,
there's no point setting $usbethaddr based on the device fuses. Use the
model detection code to gate this. Note that the fuses are actually
programmed even on those devices though.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
As agreed with Steve Rae I'm taking over maintenance of the
semihosted, emulated FVP/foundation model Versatile Express
64 bit board variant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Since commit 4a271cb1b4 (exynos: usb: Switch USB VBUS GPIOs to be
device tree configured) it's not needed for the board specific files to
turn on the VBUS GPIO by hand as that gets done based on device tree. So
drop the redundant code from the SMDK5420 board file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Not all exynos 5420 based devices with an LCD also have a parade LVDS
bridge. So make sure compilation doesn't break if CONFIG_LCD is enabled
and CONFIG_VIDEO_PARADE is not.
As a side-effect move the parade functions from the exynos system header
file to its own file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for Odroid-XU3.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The weak mxs_adjust_memory_params function is called from spl_mem_init.c,
so it must be linked into the SPL to have an effect. Move it from
mx23_olinuxino.c to spl_boot.c.
This change was verified by reading back the register values.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Otherwise NAND booting is likely to fail. Since this disables the NAND related
clocks and SPL can't load the main U-Boot from NAND.
This problem was introduced with this patch:
e25fbe3f (gw_ventana: Move the DCD settings to spl code)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
We don't have driver for the Intel Topcliff PCH Gigabit Ethernet
controller for now, so enable the Intle E1000 NIC support, which
can be plugged into any PCIe slot on the Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.
Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement minimum required functions for the basic support to
queensbay platform and crownbay board.
Currently the implementation is to call fsp_init() in the car_init().
We may move that call to cpu_init_f() in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Jetson TK1 has an ethernet NIC connected to the PCIe bus and routes
the second root port to a miniPCIe slot. Enable the PCIe controller and
the network driver to allow the device to boot over the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PCIe bus on Cardhu is routed to the dock connector. An ethernet NIC
is available on the dock over the PCIe bus. Enable the PCIe controller
and the network device driver so that the device can boot over the
network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.
Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add proper error checking into the PHY tuning patch. Make the PHY tunning only
happen in case the KSZ9021 PHY is enabled in config. Call the config callback
after the tuning finished.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Pavel Machek <pavel@denx.de>
A new interface is introduced to support generic board structure.
Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently the ROM_SIZE is hardcoded to 8MB in arch/x86/Kconfig. This
will not be the case when adding additional board support. Hence we
make ROM_SIZE configurable (512KB/1MB/2MB/4MB/8MB/16MB) and have the
board Kconfig file select the default ROM_SIZE.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.
This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.
The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
