OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.
U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1
U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)
CPU: Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM: 256 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1
U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)
CPU: Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM: 512 MiB
MMC: FSL_SDHC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot: 0
isiotmx6ul>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This device tree has been extracted from v4.9 kernel
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix warnings reported when built with W=1, by DTC 1.4.2 or later:
Node /memory has a reg or ranges property, but no unit name
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Linux Commit 9c0da3cc61f1 ("ARM: dts: explicitly mark skeleton.dtsi
as deprecated") declared that skeleton.dtsi was deprecated.
Move the memory node below to suppress warnings of FDTGREP.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit 26b09c022a ("ARM: uniphier: move SBC and Support Card
init code to U-Boot proper"), SPL does not need pin-mux settings for
the System Bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Miniarm is the internal project code. Now it is officially named Tinker board.
So rename it.
Signed-off-by: Eddie Cai <eddie.cai@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
miniarm board use lpddr3
Signed-off-by: Jacob Chen <jacob2.chen@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Added 'rockchip:' prefix to subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Change-Id: I84c3679dab2dbd8d01c1ebfd22220946d07c03cd
To use driver-model adds the pmic node for max8997.
This is used as kernel device-tree in Linux.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As reported in [1], rename the k2* dts files to keystone-* files
this will force consistency throughout.
Script for the same (and hand modified for Makefile and config
files):
for i in arch/arm/dts/k2*
do
b=`basename $i`;
git mv $i arch/arm/dts/keystone-$b;
sed -i -e "s/$b/keystone-$b/g" arch/arm/dts/*[si]
done
This is similar to linux kernel commit 5edafc29829bc ("ARM: dts: k2*: Rename
the k2* files to keystone-k2* files")
[1] http://marc.info/?l=linux-arm-kernel&m=145637407804754&w=2
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for programmable MAC impedance configuration and
fix typo in DT impedance parameters names.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The pinmuxing for i.MX53 FEC ethernet copied from
<kernel>/arch/arm/boot/dts/imx53-qsb-common.dtsi (at least until v4.9)
was bad. It is different from the manual pinmuxing in
<u-boot>/board/freescale/mx53loco/mx53loco.c which was used in
cx9020 implementation previously before mainlining into u-boot.
It seems the bug in imx53-qsb kernel device tree is hidden for so long,
because it was never used, by the kernel driver.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
This patch adds the DTS source files needed for stm32f746-disco board
The files are based on the stm32f429/469 files from current linux
kernel.
Source for "arch/arm/dts/armv7-m.dtsi": Linux: "arch/arm/boot/dts/armv7-m.dtsi"
Signed-off-by: Michael Kurz <michi.kurz@gmail.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
Clock Driver
This driver is ast2500-specific and is not compatible with earlier
versions of this chip. The differences are not that big, but they are
in somewhat random places, so making it compatible with ast2400 is not
worth the effort at the moment.
SDRAM MC driver
The driver is very ast2500-specific and is completely incompatible
with previous versions of the chip.
The memory controller is very poorly documented by Aspeed in the
datasheet, with any mention of the whole range of registers missing. The
initialization procedure has been basically taken from Aspeed SDK, where
it is implemented in assembly. Here it is rewritten in C, with very limited
understanding of what exactly it is doing.
Reviewed-by: Simon Glass <sjg@chromium.org>
The LS1046A processor has three integrated USB 3.0 controllers
(USB1, USB2, and USB3) that allow direct connection to the USB
ports with appropriate protection circuitry and power supplies.
USB1 and USB2 ports are powered by a NX5P2190UK device, which
supplies 5v power at up to 1.2 A. The power enable and
power-fault-detect pins are connected to the LS1046A processor
via CPLD for individual port management.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the SDHCI device tree nodes to the Armada 7040-db
dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SDHCI device tree nodes to the Armada AP806 dtsi
file which is used by the Armada 7k/8K SoCs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SDHCI device tree nodes to the Armada 3700-db
dts file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
This patch adds the SDHCI device tree nodes to the Armada 3700 dtsi
file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
All the UniPhier DT files are compiled if CONFIG_ARCH_UNIPHIER
is enabled, but not all of them actually work. For example, when
U-Boot is compiled for ARM 32 bit, 64 bit DT files are also built,
and vice versa. Compile only the combination that makes sense.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The LS1012A processor has two integrated USB controllers.
One is USB2.0 controller, the other is USB3.0 controller that
allow direct connection to the USB ports with appropriate
protection circuitry and power supplies.
Signed-off-by: Tang Yuantian <yuantian.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the i2c_5 node and pmic as its child node.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
For Getting from uclass, use the "max8998-pmic" as name.
It also needs to change the dt-node's name as "max8998-pmic".
Otherwise, it doesn't find the pmic device.
Because it's only searching for 'max8998_pmic'.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The OrangePi Zero can happily use the EMAC along with its integrated
PHY to use Ethernet (for TFTP booting, for instance).
Add the emac node to the board .dts by copying it from the OrangePi One
DT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
