The tsec driver contains a hard-coded array of configuration information
for the tsec ethernet controllers. We create a default function that works
for most tsecs, and allow that to be overridden by board code. It creates
an array of tsec_info structures, which are then parsed by the corresponding
driver instance to determine configuration. Also, add regs, miiregs, and
devname fields to the tsec_info structure, so that we don't need the kludgy
"index" parameter.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This is to prepare the way for board code passing in the tsec_info structure
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The Vitesse VSC8601 RGMII PHY has internal delay for both Rx
and Tx clock lines. They are configured using 2 bits in extended
register 0x17.
Therefore CFG_VSC8601_SKEW_TX and CFG_VSC8601_SKEW_RX have
been introduced with valid values 0-3 giving 0.0, 1.4,1.7 and 2.0ns delay.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
--
drivers/net/tsec.c | 6 ++++++
drivers/net/tsec.h | 3 +++
2 files changed, 9 insertions(+), 0 deletions(-)
RTL8211B sets link state register after autonegotiation complete,
so with bootdelay=0 RTL8211B will report lack of the link.
To fix this, we should wait for aneg to complete, even if the
link is currently down.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add the support of RealTek RTL8211B PHY, the RTL8211B
PHY only supports RGMII and MII mode.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The current TSEC driver limits MDIO access to the devices that have been configured as attached
to a TSEC MAC. This patch allows access to any PHY device on the MDIO bus through the 'mii' commands.
Signed-off-by: Michael Firth <michael.firth@bt.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Change return values of init() functions in all Ethernet drivers to conform
to the following:
>=0: Success
<0: Failure
All drivers going forward should return 0 on success. Current drivers that
return 1 on success were left as-is to minimize changes.
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-By: Timur Tabi <timur@freescale.com>
The MPC837xEMDS board support:
* DDR2 400MHz hardcoded and SPD init
* Local bus NOR Flash
* I2C, UART, MII and RTC
* eTSEC RGMII
* PCI host
Signed-off-by: Dave Liu <daveliu@freescale.com>
