Commit Graph

7 Commits

Author SHA1 Message Date
Giuseppe Pagano
98d0122924 udoo: Add SATA support on uDoo Board.
Add SATA support on uDoo Board.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
2013-12-17 18:14:21 +01:00
Giuseppe Pagano
db6801dec3 udoo: Fix watchdog during kernel boot.
uDoo uses APX823-31W5 watchdog chip. Timeout is about 1.2 seconds.
To disabled watchdog during kernel boot, WDI pin of that chip needs to be
in "high impedance" state. I.mx6 gpio configuration does not contemplate
tristate, so pin is set as input in high impedance.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
2013-11-28 09:08:42 +01:00
Giuseppe Pagano
078813d21d udoo: Add ethernet support (FEC + Micrel KSZ9031).
Add Ethernet and networking support on uDoo board (FEC +phy Micrel KSZ9031).
Ethernet speed is currently limited to 10/100Mbps.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
2013-11-28 08:28:54 +01:00
Giuseppe Pagano
953ab736af udoo: Move and optimize platform register setting.
Previous uDoo configuration adopts register settings for DDR3, clock, muxing,
etc. taken from Nitrogen6x. uDoo schematics is rather different from that board,
and it needs customized setting for most of the registers.
All this changes can be considered atomical since it is part of initial support
of the board.

Patch changes uDoo configuration files path to a specific one, and adopt
optimized value for every configured register.

Signed-off-by: Giuseppe Pagano <giuseppe.pagano@seco.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
2013-11-28 08:28:54 +01:00
Eric Nelson
10fda48779 i.MX6DQ/DLS: replace pad names with their Linux kernel equivalents
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-11-13 10:19:50 +01:00
Albert ARIBAUD
85b8c5c4bf Merge branch 'iu-boot/master' into 'u-boot-arm/master'
Conflicts:
	arch/arm/cpu/arm926ejs/mxs/Makefile
	board/compulab/cm_t35/Makefile
	board/corscience/tricorder/Makefile
	board/ppcag/bg0900/Makefile
	drivers/bootcount/Makefile
	include/configs/omap4_common.h
	include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

	board/compulab/common/Makefile
	board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

	include/configs/am335x_igep0033.h
	include/configs/omap3_igep00x0.h
2013-11-09 22:59:47 +01:00
Fabio Estevam
0c5e26678b udoo: Add initial support for mx6q udoo board
Add basic support for mx6q udoo board.

For further information about Udoo board:
http://www.udoo.org/

Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-10-17 09:44:20 +02:00