This change is required due to trusted OS (OP-TEE) not being position
independent code, it requires compile time fixed base address.
To take care of this it is assumed that all layerscape armv8 platforms
has minimum 2G ddr in first region. So we can have fixed address
space (66 MB -> (2MB for PPA + 64MB for trusted OS)) allocated from
top of first 2G ddr region and compile trusted OS with this fixed
base address.
But one exception here is ls1012 where we have only 1G (rdb) or 512M
(frdm) ddr memory. For those we can have different fixed compile time
base addresses for trusted OS.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high jitter
frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Convert the arm architecture to make use of the new asm-generic/io.h to
provide address mapping functions. As the generic implementations are
suitable for arm this is primarily a matter of removing code.
This has only been build-tested, feedback from architecture maintainers
is welcome.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need TPL_SYSRESET
for do_reset() in TPL for Rockchip SoCs.
References: 87c16d4 "drivers: spl: consistently use the $(SPL_TPL_)
macro"
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Falcon mode, is updating DDR dt node configuration through
spl_fixup_fdt() so add appropriate DDR base and size through
dram_init_banksize.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The (Qseven) BIOS_DISABLE signal on the RK3399-Q7 (Puma) keeps the
eMMC and SPI in reset initially and we need to write a GPIO to turn
them on before continuing the boot-up.
This adds the DTS entries for the additional regulator and makes
pinctrl and gpio3 available during SPL. It also adds a hook to the
spl_board_init() to ensure that the regulator gets probed and enabled.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the general case, we want to continue booting the full U-Boot
(contained in a discoverable FIT image) from the same device the SPL
stage was loaded from. This prepends the 'same-as-spl' specifier to
our configurable boot-order to make this the default behaviour.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support the new "same-as-spl" specifier in the boot-order on the
RK3399, this implements the chip-specific mapping from the information
obtainable from the BROM to a OF path name.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is often desirable to configure the spl-boot-order (i.e. the order
that SPL probes devices to find the FIT image containing a full U-Boot)
such that it contains 'the same device the SPL stage was booted from'
early on. To support this, we introduce the 'same-as-spl' specifier
for the spl-boot-order property.
This commit adds:
- documentation for the new board_spl_was_booted_from() function that
individual SoCs/boards should provide, if they can determine where
the SPL was booted from
- implements the new board_spl_was_booted_from() stub function
- adds support for handling the 'same-as-spl' specifier and calling
into the per-SoC/per-board support code.
This also updates the documentation for the 'u-boot,spl-boot-order'
property.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the expectation that the spl-boot-order code will eventually
gain use outside of mach-rockchip: let's add documentation on the
spl_node_to_boot_device() function, which is likely to become a
publicly exported function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Rockchip BROM allows reading where it booted from from SRAM.
This adds the necessary definitions (as received from Kever) for
the location of this information in the RK3399's SRAM and naming
for the constants used.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The later-stage spl_board_init (as opposed to board_init_f) should set
up board-specific details: these differ between the EVB-RK3399 and the
RK3399-Q7 (Puma).
This moves spl_board_init back into the individual boards and removes
the unneeded functionality from Puma.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The boot mode for rk322x is stored in sysreg 0, update it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
add i2c1 and rk805 nodes to support rk805 init setting.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the size of SPL can't be exceeded 0x8000 bytes in RK3288,
it is not possible add new SPL features like Falcon mode or etc.
So add TPL stage so-that adding new features to SPL is possible.
- TPL: DRAM init, clocks
- SPL: MMC, falcon, etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
configure_l2ctlr will be shared between SPL and TPL so
move them into asm/arch/sys_proto.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
L2CTLR read/write functions are common to armv7 so, move
them in to include/asm/armv7.h and use them where ever it need.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Backed out the change to arch/arm/mach-tegra/cache.c:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Some of macros definition are not correct, fix them according to TRM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Instead of directly calling into the back-to-bootrom code, the RK3399
common SPL implementation now uses BOOT_DEVICE_BOOTROM to trigger a
transfer back into the bootrom.
With this factored out, the spl_board_init function can not be
customised for each RK3399 board.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver for rk322x to support sdram initialize in SPL.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since we have CONFIG_RAM framwork and its driver folder, move the driver
into it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the Rockchip SARADC driver for all Rockchip SoCs.
Note that the SARADC peripheral is available on all SoCs except the
RK3036 and RK3228. However, as this is a DM-driver, enabling by
default will not cause any function problems (and can always be
changed from defconfig, if size is a concern).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the SARADC for download key pressed detect.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 8-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The clk_saradc is dividing from the 24M, clk_saradc=24MHz/(saradc_div_con+1).
SARADC integer divider control register is 10-bits width.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This re-syncs omap3 DTS file with current file from
Linux v4.14-rc1 to ensure a consistent configuration. Upstream
Linux removed the redundant Interrupt-parent property from usbhsohci,
usbhsehci, ssi_port1 and ssi_port2 sub nodes.
Signed-off-by: Karthik Tummala <karthik@techveda.org>
With DM enabled, gpio numbering is assigned based on the
probed order of gpios, irrespective of the gpio base. So enable
all necessary gpios in SPL.
Fixes: edf25d94d55c (“ARM: dts: OMAP5+: Enable gpio in SPL”)
Reported-by: Gou, Hongmei <h-gou@ti.com>
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds support for authentication of both plain
text and encrypted binaries. A new SECDEV package is needed
to enable encryption of binaries by default for AM3x.
The ROM authentication API detects encrypted images at
runtime and automatically decrypts the image if the
signature verification passes.
Addition of encryption on AM3x results in a change in the
image format. On AM4x, AM5x and, on AM3x devices signing
clear test images, the signature is appended to the end of the
binary.
On AM3x, when the SECDEV package is used to create signed
and encrypted images, the signature is added as a header
to the start of the binary. So the binary size calculation
has been updated to reflect this change.
The signing tools and encrypted image format for AM3x
cannot be changed to behave like AM4x and AM5x to
maintain backward compatibility with older Sitara
M-Shield releases.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
With the device tree ported from Linux 4.13, this enables
Driver Model and Device Tree support for the am3517-evm
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
To keep the DTS and DTSI files clean and in sync with Linux, new
u-boot.dtsi files are added.
There are some spacing issues in the patch, but they appear to be
present in the Linux source files. I'll try to get to fixing them there,
and do a future re-sync at a later date.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be,
and that it is safe to use SPL_STACK_R and provide a default value for
it. select this and re-sync the defconfigs.
Signed-off-by: Tom Rini <trini@konsulko.com>
With DM now enabled with the device tree pulled from Linux, we can
enable DM_I2C in U-Boot.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add DM_I2C_COMPAT to da850_am18xxevm to fix warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
A few small additional items are needed to support DM_SPI and
DM_SERIAL, so those were added to da850-evm-u-boot.dtsi
Signed-off-by: Adam Ford <aford173@gmail.com>
The ClearFog Base boot from UART when setting the DIP switches to 01001.
Unfortunately, the SPL code sometimes fails to detect the UART boot
method at run-time. Add an alternative SAR UART boot value to fix this.
Note that this alternative value is not documented (Armada 38x Hardware
Specifications, Table 48). But experimentations showed it on the
ClearFog Base.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
dram_ecc_scrubbing() had code to skip unused DRAM banks but it would not
work because mvebu_sdram_bs() returns 0 and the code was subtracting 1
before checking the size. Remove the -1 from the bank size and the +1
from the total which will skip unused banks and still calculate the
correct size. Put the -1 where it is needed for scrubbing via the xor
engine.
Reported-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Armada-38x has 1.8GHz and 2.0GHz variants. Add entries for these
variants to the sar_freq_tab.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Display more information about the current RAM configuration. With these
changes the output on a 88F6820 board is
SoC: MV88F6820-A0 at 1600 MHz
DRAM: 2 GiB (800 MHz, 32-bit, ECC not enabled)
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
These SoCs are network packet processors (switch chips) with integrated
ARMv7 cores. They share a great deal of commonality with the Armada-XP
CPUs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_MVNETA
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
