STM32 RTC manages only 2 digits for YEAR
(Year tens and units in BCD format in RTC_DR register).
With this patch, RTC driver assumes that tm->tm_years is between
2000 and 2099; tm->tm_year - 2000 have only 2 digit
(0 > and <= 99).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add an implementation of the rtc_enable_32khz_output() that uses the
driver model i2c APIs.
Also put code related to rtc_enable_32khz_output
under CONFIG_RTC_ENABLE_32KHZ_OUTPUT.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Add an implementation of the ds3231 driver that uses the driver
model i2c APIs.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
add m41t11 support in ds1307 driver. changes:
- add compatible string for m41t11
- check if RTC clock is running, if not
enable the clock
Signed-off-by: Heiko Schocher <hs@denx.de>
The previous pcf2127 RTC chip could not read and set the correct time.
When reading the data of internal registers, the read address was the
value of register plus 1. This is because this chip requires the host
to send a stop signal after setting the register address and before
reading the register data.
This patch sets the register address using dm_i2c_write and reads
the register data using the original dm_i2c_xfer in order to generate
a stop signal after the register address is set, and fixes the bug of
the original read and write time.
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This adds a compatible string for m41t82. This ensures that this driver
can be used for m41t82 in DM mode, too (asit was usable for this model in
non-DM mode before).
In addition, the HT bit has to be reset during probe, since the m41t82
chip sets it when entering battery standby mode.
This patch ensures this driver works on socfpga_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
After this change the m41t62.c can be used with RTC subsystem (i.e. date
command) which uses device model (DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This change facilitates the conversion of m41t62 RTC driver to device
model (DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch moves the RTC M41T62 config define to Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Variable 'days' must be defined as signed int. Otherwise the conversion
fails for some dates, e.g. 2004-08-25. Cf function rtc_time64_to_tm() in
the Linux kernel source.
Fixes: 992c1db455 "drivers: rtc: resolve year 2038 problem in rtc_to_tm"
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The "Flamingo" carrier-board for the RK3399-Q7 has a RV3029 populated
and the application will use the off-module RV3029 RTC including the
battery backed SRAM.
To support this use case, this commit includes the following changes:
* updates the rv3029 driver to use DM
* implements the read8/write8 operations
This syncs the implementation with the Linux code (based on 4.17),
porting the trickle-charger support from there (with improvements to
avoid unnecessary EEPROM updates) and adheres to the Linux DTS
binding.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The MicroCrystal RV3029 driver didn't have a Kconfig entry and was not used
anywhere. Add it to Kconfig to make it selectable.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Some RTC chips have child drivers, e.g. to provide access to their
non-volatile RAM. Scan for these when binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox SPL/TPL support
Various dm-related improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
/b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
=Bfjm
-----END PGP SIGNATURE-----
Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
Add Kconfig options so that the RTC can be used in SPL and TPL. This is
helpful for accessing the contents of CMOS RAM, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be used for device register access from board code.
This allows access to capabilities in the RTC chip not abstracted in
U-Boot's RTC class. E.g., device NVRAM or a tamper detection circuit.
Cc: Klaus Goger <klaus.goger@theobroma-systems.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With this patch, PL031 driver is converted to driver-model-compliant
driver. In addition, CONFIG_SYS_RTC_PL031_BASE is no longer valid.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
The driver sets the weekday incorrectly when called by the
'date set' command.
Sunday is 1, Saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf, table 3).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The EFI subsystem accesses the real time clock and is enabled by default.
So we should drop any CONFIG_CMD_DATE dependency from the real time clock
drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
rtc_to_tm() and rtc_mktime() are required for some RTC drivers, at least
PL031. Without this patch, we also need to enable CONFIG_CMD_DATE even if
we don't want or need this command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
For qemu-x86 the date command produces wrong days of the week:
Date: 2018-07-06 (Saturday) Time: 18:02:03
Date: 2018-07-07 (unknown day) Time: 21:02:06
According to a comment in the Linux driver the mc146818 only updates the
day of the week if the register value is non-zero.
Sunday is 1, saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf).
So let's use our library function to determine the day of the week.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Our implementation of rtc_to_tm() cannot handle dates of more than
0x7fffffff seconds after 1970-01-01.
Adopt the Linux kernel implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Split the rtc_{get,set,reset} functions so that the bodies can be used
in a DM driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the rx8025 implementation of
rtc_reset() does not need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the rs5c372 implementation of
rtc_reset() does not need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the mx27rtc implementation of
rtc_reset() can be an empty stub function.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the ds1374 implementation of
rtc_reset() doesn't need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the ds1307 implementation of
rtc_reset() doesn't need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds devicemodel support to the ISL1208 driver.
This patch drops the non-dm API as no board was using it anyway.
Also add it to Kconfig.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new driver for RX8010SJ rtc chip. The driver implements both
formats of U-Boot driver model.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Add support for S35392A RTC. The driver supports both U-Boot driver
models.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Heiko Schocher <hs@denx.de>
RTC_CONFIG_D register contains the day within the month to generate
an alarm, not the month. This corrects the printf to indicate it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
