Commit Graph

2842 Commits

Author SHA1 Message Date
Peng Fan
216d286c7e imx: mx6: implement mmc_get_env_dev
Implement mmc_get_env_dev, devno can be got from smbr1 of SRC.
Introduce a weak function board_mmc_get_env_dev, different
boards can implement it according to different sdhc controllers
that used by the board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-04 10:13:49 +01:00
Peng Fan
62d8cce9f3 imx: mx7dsabresd: move mmc_get_env_devno to soc code
Move mmc_get_env_devno to soc.c and rename to mmc_get_env_dev to
match the one in common/env_mmc.c.
Introduce a weak function board_mmc_get_env_dev. Different
boards can implement this according to sdhc controller which
is used by the board.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-04 10:13:45 +01:00
Ye Li
23e2da27d3 imx: mx6ul/sx: Fix issue in LCDIF clock dividers calculation
The checking with max frequency supported is not correct, because the temp
is calculated by max pre and post dividers. We can decrease any divider to
meet the max frequency limitation. Actually, the calculation below the codes
is doing this way to find best pre and post dividers.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-02 21:25:50 +01:00
Ye Li
9655ebdd50 imx: mx6sx: Fix issue in LCDIF clock enablement
Wrong checking for the base_addr paramter with LCDIF1 and LCDIF2. Always
enter the -EINVAL return.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2016-02-02 21:25:05 +01:00
Ye Li
cf94a3427a imx: mx6sxsabreauto: Add support for mx6sx SABREAUTO board
Initial version for mx6sx SABREAUTO board support with features:
PMIC, QSPI, NAND flash, SD/MMC, USB, Ethernet, I2C, IO Expander.

Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02 21:04:21 +01:00
Ye Li
d4d1dd6749 mx6: soc: Add ENET2 mac address support
The i.MX6SX and i.MX6UL has two ENET controllers, add support for reading
MAC address from fuse for ENET2.

Signed-off-by: Ye Li <ye.li@nxp.com>
2016-02-02 21:03:59 +01:00
Marek Vasut
d339f16911 arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL
Add DDR3 calibration code for i.MX6Q, i.MX6D and i.MX6DL. This code
fine-tunes the behavior of the MMDC controller in order to improve
the signal integrity and memory stability.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2016-02-02 20:58:46 +01:00
Tom Rini
008e61f512 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-02-02 06:51:05 -05:00
Ashish kumar
2ea3a448cc armv8: ls2080a: Implement workaround for core errata 829520, 833471
829520: Code bounded by indirect conditional branch might corrupt
instruction stream.
Workaround: Set CPUACTLR_EL1[4] = 1'b1 to disable the Indirect
Predictor.

833471: VMSR FPSCR functional failure or deadlock.
Workaround: Set CPUACTLR[38] to 1, which forces FPSCR write flush.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-02-01 13:58:22 -08:00
Wang Dongsheng
c5e954eccd ARM: Disable "DISCARD" for secure section if CONFIG_ARMV7_SECURE_BASE isn't defined
"DISCARD" will remove ._secure.text relocate, but PSCI framework
has already used some absolute address those need to relocate.

Use readelf -t -r u-boot show us:
.__secure_start		addr: 601408e4
.__secure_end		addr: 60141460

60141140  00000017 R_ARM_RELATIVE
46	_secure_monitor:
47	#ifdef CONFIG_ARMV7_PSCI
48      ldr     r5, =_psci_vectors

60141194  00000017 R_ARM_RELATIVE
6014119c  00000017 R_ARM_RELATIVE
601411a4  00000017 R_ARM_RELATIVE
601411ac  00000017 R_ARM_RELATIVE
64	_psci_table:
66	.word	psci_cpu_suspend
...
72	.word	psci_migrate

60141344  00000017 R_ARM_RELATIVE
6014145c  00000017 R_ARM_RELATIVE
202	ldr     r5, =psci_text_end

Solutions:
1. Change absolute address to RelAdr.
   Based on LDR (immediate, ARM), we only have 4K offset to jump.
Now PSCI code size is close to 4K size that is LDR limit jump size,
so even if the LDR is based on the current instruction address,
there is also have a risk for RelAdr. If we use two jump steps I
think we can fix this issue, but looks too hack, so give up this way.

2. Enable "DISCARD" only for CONFIG_ARMV7_SECURE_BASE has defined.
   If CONFIG_ARMV7_SECURE_BASE is defined in platform, all of secure
will in the BASE address that is absolute.

Signed-off-by: Wang Dongsheng <dongsheng.wang@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-31 16:32:56 +01:00
Marek Vasut
11aa6a32eb arm: cache: Implement cache range check for v7
Add code to aid tracking down cache alignment issues.
In case DEBUG is defined in the cache.c, this code will
check alignment of each attempt to flush/invalidate data
cache and print a warning if the alignment is incorrect.
If DEBUG is not defined, this code is optimized out.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
2016-01-31 16:32:56 +01:00
Tom Rini
82d72a1b99 Merge branch 'master' of git://git.denx.de/u-boot-net 2016-01-28 18:42:10 -05:00
Bin Meng
afe6462da9 arm: ls102xa: Rewrite the logic of ft_fixup_enet_phy_connect_type()
eth_get_dev_by_index() is an API which is not available in driver
model. Use eth_get_dev_by_name() instead, which can also simplifly
the code logic a little bit.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2016-01-28 12:23:22 -06:00
Tom Rini
cd85bec36d Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2016-01-27 15:05:36 -05:00
Gong Qianyu
166ef1e90c armv8/ls1043aqds: add QSPI support in SD boot
QSPI and IFC are pin-multiplexed on LS1043A. So we use
ls1043aqds_sdcard_ifc_defconfig to support IFC in SD boot and
ls1043aqds_sdcard_qspi_defconfig to support QSPI in SD boot.

Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:28:55 -08:00
Aneesh Bansal
d041288586 secure_boot: enable chain of trust for ARM platforms
Chain of Trust is enabled for ARM platforms (LS1021 and LS1043).
In board_late_init(), fsl_setenv_chain_of_trust() is called which
will perform the following:
- If boot mode is non-secure, return (No Change)
- If boot mode is secure, set the following environmet variables:
   bootdelay = 0 (To disable Boot Prompt)
   bootcmd = CONFIG_CHAIN_BOOT_CMD (Validate and execute Boot script)

Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com>
Acked-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-27 08:12:49 -08:00
Michal Simek
be6f6af1d6 ARM64: zynqmp: Add initial support for the first silicon
Add basic configuration for the first silicon.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Michal Simek
0785dfd8a7 ARM64: zynqmp: Use the same U-Boot version with/without ATF
Remove SECURE_IOU option which is not needed. U-Boot itself can detect
which EL level it is on and based on that use do platform setup.
It also simplify usage because one Kconfig entry is gone.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2016-01-27 15:55:56 +01:00
Vishnu Patekar
f3ad64c88c sunxi: Add support for LPDDR3 for A83T
Banana-pi M3 has LPDDR3 DRAM. this adds support for LPDDR3 for A83T.
Mostly the timing parameters are different from DDR3.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Vishnu Patekar
f5fd8caf7f sunxi: Groundwork to support new dram type for A83T
Different A83T boards have different DRAM types. Banapi M3 has LPDDR3,
Allwinner Homlet v1.2 has DDR3.

This adds groundwork to support for new DRAM type for A83T.

Introduce CONFIG_DRAM_TYPE, It'll be 3 for DDR3 and 7 for LPDDR3, must
be set in respective board defconfig.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Vishnu Patekar
627b380f62 sunxi: Redundant code cleanup from a83t dram init
This removes the redundant lines of code from mctl_sys_init.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Chen-Yu Tsai
9683945179 sunxi: Support PSCI ops on Allwinner H3
H3 has the same power sequencing procedure as the A31/A31s, which
includes the power clamps.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Chen-Yu Tsai
ed80584f30 sunxi: Support H3 CCU security switches
H3's CCU includes some switches which disable non-secure access to some
of the more critical clock controls, such as MBUS, PLLs, and main
platform busses.

Configure them to enable non-secure access.

For now the only SoC that has this feature is the H3. For other
platforms just use a default (weak) empty function so things do
not break.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:05 +01:00
Chen-Yu Tsai
5823664fb8 sunxi: Support Secure Memory Touch Arbiter (SMTA) in sun8i H3
Secure Memory Touch Arbiter is the same thing as the TrustZone
Protection Controller found on A31/A31s.

Access to many peripherals on the H3 can be controlled by the SMTA,
and the settings default to secure access only.

This patch supports the new settings, and sets them to allow non-secure
access.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-01-26 16:20:04 +01:00
Pratiyush Mohan Srivastava
191e3c0527 armv8: Enable all 8 DPMAC ports in LS2080A Personality
LS2080A has support for 8 DPMAC ports out of which
only 5 ports can be used at a time.
Enabling all 8 DPMAC ports of LS2080A personality.

Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:17 -08:00
Tang Yuantian
1ef7ac70e2 arm: ls1021a: Adjust sata register default values
Updated the default sata register values to enhance the
performance and stability.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:15 -08:00
Prabhakar Kushwaha
6f14e257c4 armv8: fsl-lsch3: fixup SYSCLK frequency in device tree
SYSCLK frequency is dependent on on-board switch settings. It may
vary as per requirement. boot-loader is aware of board switch
configurations.

So Fixup Linux device tree from boot-loader.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-01-25 08:24:15 -08:00
Peng Fan
d9699de85c imx: mx7: default enable MDIO open drain
The management data input/output (MDIO) requires open-drain,
i.MX7D TO1.0 ENET MDIO pin has no open drain, but TO1.1 supports
this feature. So to TO1.1, need to enable open drain by setting
bits GPR0[8:7] for TO1.1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-24 12:15:14 +01:00
Peng Fan
9ba18ff8ef imx: mx6ul/sx: fix mmdc_ch0 clk calculation
Check "Figure 19-5. BUS clock generation" of i.MX 6SoloX Applications
Processor Reference Manual and "Figure 18-5. BUS clock generation" of
i.MX 6UltraLite Applications Processor Reference Manual. If mmdc clk
sources from pll4_main_clk(pll_audio), the calculation is wrong.

Fix mmdc_ch0 clk calculation. Also add PLL_AUDIO/VIDEO support
for decode_pll.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-24 12:13:21 +01:00
Tom Rini
6905f4d3c7 Merge git://git.denx.de/u-boot-dm 2016-01-21 11:49:49 -05:00
Jelle van der Waa
9d0826879e sunxi: Add support for the I2C controller which is part of the PRCM
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: Minor cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>

applied with fixing 2 checkpatch warnings:
WARNING: please, no space before tabs

Signed-off-by: Heiko Schocher <hs@denx.de>
2016-01-21 07:30:01 +01:00
Mugunthan V N
28a6c01187 arm: omap-common: do not build timer when CONFIG_TIMER defined
To prepare timer driver to DM/DT conversion do not build the
exiting timer driver when CONFIG_TIMER is defined. But since
omap's SPL doesn't support DM yet so built timer driver only for
SPL build when CONFIG_TIMER is defined.

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-01-20 19:06:21 -07:00
Vikas Manocha
0a61ee880c stm32: move stm32 specific code to mach-stm32
This patch moves stm32 sources at one place, with this armv7m now contains
only generic stuff.

Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
2016-01-20 10:19:41 -05:00
Ladislav Michl
bfb7cc3340 armv7: Add missing newline after OMAP die ID
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Enric Balletbo Serra <enric.balletbo@collabora.com>
2016-01-20 10:19:38 -05:00
Sergey Temerkhanov
a5b9fa30ce armv8: Add Secure Monitor/Hypervisor Call (SMC/HVC) infrastructure
This commit adds functions issuing calls to secure monitor or
hypervisore. This allows using services such as Power State
Coordination Interface (PSCI) provided by firmware, e.g. ARM
Trusted Firmware (ATF)

The SMC call can destroy all registers declared temporary by the
calling conventions. The clobber list is "x0..x17" because of
this

Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
2016-01-19 22:25:36 +00:00
Sergey Temerkhanov
94f7ff36e5 armv8: New MMU setup code allowing to use 48+ bits PA/VA
This patch adds code which sets up 2-level page tables on ARM64 thus
extending available VA space. CPUs implementing 64k translation
granule are able to use direct PA-VA mapping of the whole 48 bit
address space.
It also adds the ability to reset the SCTRL register at the very beginning
of execution to avoid interference from stale mappings set up by early
firmware/loaders/etc.

Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
2016-01-19 22:25:36 +00:00
Vladimir Zapolskiy
1222305b55 arm: lpc32xx: switch SPL builds to driver model
For NXP LPC32xx boards the change enables SPL_DM option, this allows
to use any driver model UART driver in SPL images, hence a restriction
on HSUART in SPL image is removed and well as definitions for non-DM
NS16550 driver, its DM version is used instead.

Because SPL_DM requires malloc(), enable CONFIG_SPL_SYS_MALLOC_SIMPLE
for LPC32xx boards.

The change adds about 5KB to the resulting SPL image (for devkit3250
board SPL image is increased from 10672 to 15608 bytes).

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13 21:05:22 -05:00
Vladimir Zapolskiy
d25ba89e8b arm: lpc32xx: switch serial console to driver model
On NXP LPC32xx platform for non-SPL builds the change adds
standard (NS16550) and high-speed UARTs to driver model.
Due to specific of DM NS16550 device description UART clock can not be
got in runtime and by default it is set to 13MHz, if board PERIPH_CLK
is different, this should be specified in board configuration file.

For SPL builds HSUARTs are disabled and non-DM NS16550 driver is
compiled, if needed.

The change also updates default configs of devkit3250 and work_92105
boards to reflect updates in platform files.

Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-01-13 21:05:22 -05:00
Tom Rini
90345c92a8 am33xx/am43xx: Add platform data for GPIOs
On these platforms we have many cases of boards that enable device model
and GPIO support but do not enable OF_CONTROL and pass in a device tree
with the binary.  We need to bring in the platform data here as well.

Tested on Beaglebone Black.

Reported-by: Robert Nelson <robertcnelson@gmail.com>
Reported-by: Francisco Aguerre <franciscoaguerre@gmail.com>
Reported-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-01-08 10:15:45 -05:00
Tom Rini
f1993ca066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-01-03 10:32:24 -05:00
Michael Heimpold
fe21eaf92d ARM: mxs: allow boards to select DC-DC switching clock source
For some board designs, it might be useful to switch the DC-DC
clock source to something else rather the default 24 MHz, e.g.
for EMI reasons.

For this, override the mxs_power_setup_dcdc_clocksource function
in your board support files.

Example:
void mxs_power_setup_dcdc_clocksource(void)
{
    mxs_power_switch_dcdc_clocksource(POWER_MISC_FREQSEL_20MHZ);
}

Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2016-01-03 15:56:36 +01:00
Peng Fan
839479dda6 imx: ddr: drop duplicated debug info
Drop duplicated debug info for tcl.

Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-01-03 15:19:58 +01:00
Mingkai Hu
0d6faf2bd0 armv8/ls1043a: Implement workaround for PEX erratum A009929
Consecutive write transactions from core to PCI express outbound
path hangs after 25 to 30 transactions depending on core freq.
This erratum enable the mbist clock through COP register setting.

Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-17 08:52:18 +08:00
Tom Rini
e6e3faa5c2 Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2015-12-14 20:27:23 -05:00
Tang Yuantian
989c5f0a8f armv8: Add sata support on Layerscape ARMv8 board
Freescale ARM-based Layerscape contains a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls2080aqds, ls2080ardb and
ls1043aqds boards.

Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:35 +08:00
Aneesh Bansal
70f959c3c4 armv8: Make SEC read/write as snoopable for LS1043
For LS1043, SEC read/writes are made snoopable by setting
the corresponding bits in SCFG to avoid coherency issues.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:34 +08:00
Aneesh Bansal
b644d3e932 armv8: define usec2ticks function
usec2ticks() function has been defined for ARMv8 which will
be used by SEC Driver.

Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:34 +08:00
York Sun
c04921414c armv8: fsl-layerscale: Rewrite reserving memory for MC and debug server
MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.

In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:33 +08:00
York Sun
c107c0c05c armv8: fsl-layerscape: Make DDR non secure in MMU tables
DDR has been set as secure in MMU tables. Non-secure master such
as SDHC DMA cannot access data correctly. Mixing secure and non-
secure MMU entries requirs the MMU tables themselves in secure
memory. This patch moves MMU tables into a secure DDR area.

Early MMU tables are changed to set DDR as non-secure. A new
table is added into final MMU tables so secure memory can have
2MB granuality.

gd->secure_ram tracks the location of this secure memory. For
ARMv8 SoCs, the RAM base is not zero and RAM is divided into several
banks. gd->secure_ram needs to be maintained before using. This
maintenance is board-specific, depending on the SoC and memory
bank of the secure memory falls into.

Signed-off-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:33 +08:00
Yao Yuan
000f4e7686 move erratum a008336 and a008514 to soc specific file
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file

Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-12-15 08:57:32 +08:00