- Add base support for Marvell OcteonTX2 CN9130 DB (mostly done
by Kostya)
- Sync Armada 8k MMU setup with Marvell version (misc Marvell
authors)
- spi: kirkwood: Some fixes especially for baudrate generation
(misc Marvell authors)
- mvebu: x530: Reduce SPL image size (Stefan)
- Rename "rx_training" to "mvebu_comphy_rx_training" (Stefan)
Even if only USB gadget is defined, dwc3 generic driver enables
a definition and probe/remove functions for host driver.
This enables the definition if USB_HOST is enabled only.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
All newer Allwinner SoCs (since about 2013) miss the CONFIGDATA register
in their MUSB implementation, so they need a quirk to hardcode this.
Currently this quirk depends on listing the SoCs affected in musb_reg.h,
which means that this list needs to grow with every new chip.
Move the quirk feature into Kconfig, next to PIO_ONLY, and change the
default to y (for Allwinner builds), while listing the early
implementations as exceptions.
This fixes USB peripheral operation on some newer SoCs, which were not
explicitly listed before.
Tested on H6, H616, R40 (which were broken before), and also on the H5
and A20, for regressions.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pcie_dw_mvebu configure ATU regions for memory, configuration
and IO space types. However the latter is not obligatory
and when not specified in the device tree, causes wrong
ATU configuration. Fix that by adding a dependency on the
detected PCIE regions count.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-on: https://sj1git1.cavium.com/18136
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
After commit 1fe929ed497bcc8975be8d37383ebafd22b99dd2
("spi: kirkwood: prevent configuring speed exceeding max controller freq")
the spi frequency could be set to 0 on platform where spi-max-frequency
is not defined (e.g. on armada-388-gp). Prevent limiting speed in
mentioned cases.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Marcin Wojtas <marcin@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a limitation in the kirkwood_spi driver
set_speed hook, which prevents setting too high transfer
speed.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Tested-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Armada SoC family implementation of this SPI hardware module has
extended the configuration register to allow for a wider range of SPI
clock rates. Specifically the Serial Baud Rate Pre-selection bits in the
SPI Interface Configuration Register now also use bits 6 and 7 as well.
Modify the baud rate calculation to handle these differences for the
Armada case. Potentially a baud rate can be setup using a number of
different pre-scalar and scalar combinations. This code tries all
possible pre-scalar divisors (8 in total) to try and find the most
accurate set.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When the PHY interface is set as TXID & RXID, the delays should be taken from DT,
but first they should not be hardcoded since the PHY driver will set them.
Fixes: 798424e857 ("net: designware: add Amlogic Meson8b & later glue driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the PHY isn't specified in the DT, -ENODATA means it should be skipped,
handle it like -ENOENT.
With that, devices without USB3 supported can have USB working (Odroid-HC4).
Fixes: adb049abf7 ("usb: dwc3: Add Meson G12A USB Glue")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The pwm_sifive_set_config() and pwm_sifive_set_enable() cannot work
properly due to the wrong implementations. It will cause the u-boot
PWM command to not work as expected. The bugs will be resolved in this
patch.
Signed-off-by: Vincent Chen <vincent.chen@sifive.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Variables which had previously been stored in .bss are moved to .data. In
addition, probed needs to be reset when the clock driver is re-bound
post-relocation.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
No other (real) clocks have the cpu clock as their parent; instead they are
children of aclk. Move the clint clock under aclk to match them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This simplifies the PLL creation process, since we don't have to pass all
the parameters individually.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This conditional always evaluated as false, regardless of the value of reg.
Fix it so that it properly tests the bits in the PLL register. Also test
PLL_EN, now that we set it.
Reported-by: Damien Le Moal <Damien.LeMoal@wdc.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
After starting or setting the rate of a PLL, the enable bit must be set.
This fixes a bug where the AI ram would not be accessible, because it
requires PLL1 to be running.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
If the user/dev explicitly requests a clock be assigned a certain rate,
then we should warn them if we can't do it. This makes it clear if the
clock is running at the default rate.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This patch changes the functioning of the detection of w1 devices.
The old way was a comparison between detected w1 and the ones described in
the device tree. Now it will just look for the driver matching the family
id of the w1 detected.
The patch is inspired from Maxime Ripard code.
Signed-off-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Currently driver may end up caching disabled port ID as active
interface. Fix this by bailing out earlier in case port is marked
disabled in the DT.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
CPSW NUSS IP on K3 SoCs can have more than one external port (upto 8)
Therefore increase AM65_CPSW_CPSWNU_MAX_PORTS to 9 (8 ext + 1 Root port)
as preparation to allow any one of the 8 ports to be used as ethernet
interface in U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
ICSSG Ethernet driver uses two src threads per port (one per slice).
Similarly CPSW uses one src thread.
Drop PSIL EP static data for other src threads in order to reduce
R5 SPL footprint. This makes AM65x board bootable again.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
With AM64x supporting only K3_NAV_RINGACC_RING_MODE_RING or the exposed
ring mode, all other K3 SoCs have also been moved to this common
baseline. Therefore drop other modes such as
K3_NAV_RINGACC_RING_MODE_MESSAGE (and proxy) to save on SPL footprint.
There is a saving of ~800 bytes with this change for am65x_evm_r5_defconfig.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
AM64 dual mode rings are modeled as pair of Rings objects which has common
configuration and memory buffer, but separate real-time control register
sets for each direction mem2dev (forward) and dev2mem (reverse).
AM64 rings must be requested only using k3_ringacc_request_rings_pair(),
and forward ring must always be initialized/configured. After this any
other Ringacc APIs can be used without any callers changes.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Update struct ti_sci_msg_rm_udmap_tx_ch_cfg_req to latest ABI to support
AM64x BCDMA Block copy channels.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Attempt to get and enable a vtt regulator if one is provided from the
dts. If we do not find one, continue as not all platforms have this.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce support for the AM64 DDRSS controller which uses the 16bit
variation of the controller. This controller shares much functionality
with the existing J721e support, so this patch introduces only the new
code needed for am64 specific support from "_16bit_" files with headers
under "16bit/" include path/.
Also add a CONFIG_K3_AM64_DDRSS option to the choice required for use
with CONFIG_K3_DDRSS to allow selecting AM64 support.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Introduce a new version of the ddr driver which has the ability to
support different variations of the controller. Also introduce support
for the 32bit variation of the controller which is what was already
supported by the previous version used for J721e and J7200.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Create a new CONFIG_K3_DDRSS option to select the common parts of the
k3-ddrss driver. Also introduce a choice that depends on the top level
option to select CONFIG_K3_J721E_DDRSS for j721e support, and update
corresponding Kconfig as required.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Rename the k3-j721e folder under drivers/ram to k3-ddrss in preparation
of introducing additional support for other platforms to the same
driver.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Fix the indentation for certain macros to be consistent with the other
macros in the file, as the existing indentation does not make sense in
many places.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
AM64x uses a different thread mapping that existing K3 SoCs, so update
the valid thread ID list to include those used for AM64x.
Also remove the comment identifying the purpose of each thread ID. The
purpose of the thread ID is specified when describing the threads in the
device tree and the same ID can mean different things on different SoCs,
so the comment is not useful.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Add support for the controller present on the AM642 SoC.
There are instances:
sdhci0: 8bit bus width, max 400 MBps
sdhci1: 4bit bus width, max 100 MBps
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Using the custom TI functions required not only replacing common memory
access functions but also rewriting the routines used to set bypass and
lock states. As for readl() and writel(), they also required the address
of the register to be accessed, a parameter that is hidden by the TI clk
module.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Replaces the common memory access functions used by the driver with the
ones exported from the TI clk module.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
