It is not necessary all omap5+ based uses the same PMIC
to poweron mmc. So add support for enabling mmc based on board.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
CCN-504 HPF registers were believed to be accessible only from EL3.
However, recent tests proved otherwise. Remove checking for exception
level to re-enable L3 cache flushing for all levels.
Signed-off-by: York Sun <york.sun@nxp.com>
Tested-by: Zhao Qiang <qiang.zhao@nxp.com>
The pcie config space of ls1088a is different from ls2080a.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In case high region memory doesn't have enough space for Management
Complex (MC), the return value should indicate a failure so the
caller can handle it accordingly.
Signed-off-by: York Sun <york.sun@nxp.com>
Reported-by: Ebony Zhu <ebony.zhu@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.
Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
Low Frequency Periodic Signaling(LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter
settings
Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.
Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature
Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
EC1 and EC2 are RGMII interface on ls1088aqds platform.
This patch add support of RGMII with PHY and MDIO
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
For QSPI and IFC addresses execution shouldn't be allowed
when u-boot running from DDR. Revise the MMU final table
to enforce execute-never bits.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
According current code base, CONFIG_LS1012A should be
CONFIG_ARCH_LS1012A, or function fsl_fdt_disable(blob) will be
wrongly called to disable all dwc3 USB nodes on LS1012A, which
cause Linux USB function stop working at all.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update MC address calculation as per MC design requirement of address
as least significant 512MB address of MC private allocated memory,
i.e. address should point to end address masked with 512MB offset in
private DRAM block.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
LS2080 family has CCN-504 cache coherent interconnet. Other SoCs
in LSCH3 family may have differnt interconnect.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
If CONFIG_SPL_OS_BOOT is enabled, boot OS if kernel image is found
in FIT structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL supports U-Boot image in FIT format which has data outside of
FIT structure. This adds support for embedded data for normal FIT
images.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Kconfig option SPL_GZIP and SPL_ZLIB to enable gunzip support for
SPL boot, eg. falcon boot compressed kernel image.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Unify memory map for Layerscape based platforms. This patch includes
changes in bootscript, bootscript header and PPA header addresses
change as per unified memory map.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QE_IRAM_READY should be set only after successfully uploading the
firmware.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.
When running a SPL target, which supports multiple MX6 variants we cannot
properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as
such decision is done in build-time currently.
Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be
configured in run-time on mx6.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
[agust: fixed #endif in cgtqmx6eval.h]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
At present the IDE device number is initialized to -1, which means
we cannot type "ide read" command before setting the device number
via "ide device #".
For convenience, let's set the first device as the default one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When there is no CDROM inserted, the block size is zero hence there
is no need to create a BLK device for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the IDE driver to driver model so that block read and
write are fully functional.
Fixes: b7c6baef ("x86: Convert MMC to driver model")
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far these are using magic numbers. Replace them with macros.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The underlying implementation for ENV_AES has security complications and
is not recommended for use. Please see CVE-2017-3225 and CVE-2017-3226
for more details. Mark this as deprecated now and delete this in the
medium term if no one comes forward to re-work the support.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of the config options for USB networking have been migrated to
Kconfig. Update README.usb to reflect this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig.
Update defconfigs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on
USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and
LAN78XX options under new menu. Finally update the defconfigs that need
CONFIG_USB_HOST_ETHER.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The correct name is 'gd->fdt_blob', not 'gd->blob'.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
