- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Set `bootcause' from b850v3 power management watchdog status.
Boot cause "REVERT" is no longer used, remove it.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix typo in NFS command configuration check.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Upstream linux DT naming doesn't align with the U-Boot DT, which may
not always be the case so this allows using BOOTENV_EFI_SET_FDTFILE_FALLBACK
where it might be appropriate for some boards.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For booting via UEFI we need to define the fdtfile option so
bootefi has the option to load a fdtfile from disk. For arm64
the kernel dtb is located in a vendor directory so we define
that as nvidia for that architecture.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was used for a board which is not supproted anymore and can
therefore be dropped.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This option is obsolete since 2009 and can be removed globally.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: a294ead8d2 ("dm: Use an allocated array for run-time device info")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This comment is in the wrong format, so reports an error with
'make htmldocs'. Fix it.
Fixes: b73d61a556 ("x86: zimage: Add a little more logging")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It seems nobody tested the debug() option in spin_lock_irqsave().
Currently, when #define DEBUG, it spoils the compiler with
In file included from drivers/usb/dwc3/gadget.c:18:
drivers/usb/dwc3/gadget.c: In function ‘dwc3_gadget_set_selfpowered’:
include/log.h:235:4: warning: ‘flags’ is used uninitialized in this function [-Wuninitialized]
235 | printf(pr_fmt(fmt), ##args); \
| ^~~~~~
drivers/usb/dwc3/gadget.c:1347:17: note: ‘flags’ was declared here
1347 | unsigned long flags;
| ^~~~~
and so on...
Drop useless debug() call to make compiler happy.
Fixes: 0c06db5983 ("lib, linux: move linux specific defines to linux/compat.h")
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Pack struct efi_mm_communicate_header as done in EDK2 as seen in
release 201808 [1]. If not packed sizeof() for the structure adds
4 additional bytes on 32bit targets which breaks the ABI.
Link: [1] https://github.com/tianocore/edk2/blob/edk2-stable201808/MdePkg/Include/Protocol/MmCommunication.h#L21
Fixes: 23a397d2e2 ("efi_loader: Add headers for EDK2 StandAloneMM communication")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For eMMC HS400 mode, the DLL reset is a required step for mmc rescan.
This step has not been documented in reference manual, but the RM will
be fixed sooner or later.
In previous commit to support eMMC HS400,
db8f936 mmc: fsl_esdhc: support eMMC HS400 mode
the steps to configure DLL could be found in commit message,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
14. Wait for delay chain to lock.
these would be fixed as,
13. Set DLLCFG0[DLL_ENABLE] and DLLCFG0[DLL_FREQ_SEL].
13.1 Write DLLCFG0[DLL_RESET] to 1 and wait for 1us,
then write DLLCFG0[DLL_RESET]
14. Wait for delay chain to lock.
This patch is to add the step of DLL reset, and make sure delay chain
locked for HS400.
Fixes: db8f93672b ("mmc: fsl_esdhc: support eMMC HS400 mode")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Handle the register RCC_MP_GCR without SET/CLR registers
but with a direct access to bit BOOT_MCU:
- deassert => set the bit: The MCU will not be in HOLD_BOOT
- assert => clear the bit: The MCU will be set in HOLD_BOOT
With this patch the RCC driver handles the MCU_HOLD_BOOT_R value
added in binding stm32mp1-resets.h
Cc: Fabien DESSENNE <fabien.dessenne@st.com>
Cc: Arnaud POULIQUEN <arnaud.pouliquen@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
On some board, the ID pin is not connected so the B session must be
overridden with "u-boot,force_b_session_valid" but the VBus sensing
must continue to be handle.
To managed it, this patch adds a new DT field
"u-boot,force-vbus-detection" to use with "u-boot,force_b_session_valid"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The parameter check for UEFI service GetNextVariableName() is corrected.
The dependencies of CONFIG_DFU_TFTP are simplified.
The set of supported hash algorithms reported by the EFI_TCG2_PROTOCOL is
corrected.
-----BEGIN PGP SIGNATURE-----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=6U7u
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc3-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3 (2)
The parameter check for UEFI service GetNextVariableName() is corrected.
The dependencies of CONFIG_DFU_TFTP are simplified.
The set of supported hash algorithms reported by the EFI_TCG2_PROTOCOL is
corrected.
Remove fixed configuration and detect flash based on DT.
Also increase amount of flash sectors to 2048 because on kc705 flash has
1027 sectors.
Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
XIP is not enabled in SPL. SPL_NOR is enabled but any macro setting with
using SYS_FLASH_BASE are wrong because it is not aligned with DM.
That's why change these macro and align them with TEXT_BASE macro.
Information should be find at run time based on DT but implementation is
not done yet.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to use this file anymore. Include it in main config file
and simplify logic based on it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable caches by default. For now just simplify config file but it should
be read from DT or PVRs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A lot of configs has been moved to Kconfig and it ends up in ifdef mess
with no bodies. That's why remove all of them.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This permits to find a file and use the distro_bootcmd
Reviewed-by: Joao Marcos Costa <jmcosta944@gmail.com>
Signed-off-by: Richard Genoud <richard.genoud@posteo.net>
Also change back SYS_MEMTEST_END to 0x00f00000. 0xe00000 was wrong and
introduced due to the global Kconfig migration of this option in u-boot.
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Instead of using an hard coded address, make use of an
already defined address for importing the environment
for ramfs and nfs boot. This allows boards having different
mapping to use the same code.
CC: Heiko Schocher <hs@denx.de>
CC: Tom Rini <trini@konsulko.com>
Signed-off-by: Matteo Ghidoni <matteo.ghidoni@hitachi-powergrids.com>
Signed-off-by: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Import updated device trees from Linux tag v5.9. This picks up new
hardware (PinePhone, PineTab); and it drops the U-Boot specific DTSI
files for the Pinebook and the Teres-I, since the ANX6345 bridge is
now supported upstream.
A couple of headers needed updates for recently-added hardware support.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Function twl4030_i2c_read() is like twl4030_i2c_read_u8() but instead of
single value it rather returns array of values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Since U-boot EFI implementation is getting richer it makes sense to
add support for EFI_TCG2_PROTOCOL taking advantage of any hardware TPM
available on the device.
This is the initial implementation of the protocol which only adds
support for GetCapability(). It's limited in the newer and safer
TPMv2 devices.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A following patch introduces EFI_TCG2_PROTOCOL.
Add the required TPMv2 headers to support it.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When calling ExitBootServices during out unit tests we should not detach
devices as we need console output for runtime tests.
Fixes: 529441ca89 ("efi_loader: Disable devices before handing over control")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl+kJL8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaDpAf+MajyuxlmGmFTjpyiB026aWiYE4rAn4AE
bXEDxHpOTIH4hDX7kYVWPmuKivHJo2hF0WUpIFBEAgtc2dOfjOP+mrDjBzG1Pikl
z5yuilG7eHwC1kTIkPv/tPHwDWRBI5VNwTYq0VTtffMKr8LCBo96wEYEbeYK0xdQ
kpNa9d4G+tpx20BCRgPLeOMk2pg5SVszkCCkmmPd12rO2zJ9+wWa8fwA759E93Rw
RshoRCtLNo2nEA3uJVG2aN9n3eAdM/iupDVdBLg50SFKabUxt7OcvGOC8NzGdAmT
9UbB8scvQJyI/kylGT+ghH3o2RqQGvuIRXmDyETckdkpiqK0SQvysg==
=eOGz
-----END PGP SIGNATURE-----
Merge tag 'dm-pull5nov20' of git://git.denx.de/u-boot-dm
patman status subcommand to collect tags from Patchwork
patman showing email replies from Patchwork
sandbox poweroff command
minor fixes in binman, tests
- meson64_android: don't show logo on ROM USB boot
- doc: update support matrix and fix vim3/l build instructions
- meson64: relocate config_distro_bootcmmd header
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
As a first step to obtaining SMBIOS information from the devicetree, add
an ofnode parameter to the writing functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add logging for each part of the boot process, using a new
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
