Mainline kernel has no r1p12 compatible string that's why console stops
to work with the latest DTS files. Append generic compatible string.
Keep in your mind that using this generic compatible string not all uart
features will be available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modifying device tree node to support legacy interrupts.
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds ddrc memory controller node in dts.
size mentioned in dts is 0x30000, because we need to access DDR_QOS
INTR registers located at fd090208 from this driver.
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP DMA's main clock and apb clock are added
in zynqmp DT.
Signed-off-by: VNSL Durga <vnsldurg@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
ZynqMP is not using global interrupt-parent setting that's why
it has to be listed in every node separately. PMU node missed it and
this patch is adding it.
Reported-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add power-domains to the DT and attach devices to them.
The power-domains are all logical domains as understood by firmware.
Each PD is identified by a unique identifier that the platform firmware
understands.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds broken-tuning property to SD and
eMMC nodes.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove jumbo properties which are handled in the driver directly
and use mainline compatible string which is already handled by the
driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add 8-bit bus width property to eMMC node.
Signed-off-by: P L Sai Krishna <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes compatible string as "m25p80" for qspi node in
ep108 device tree file
Signed-off-by: Ranjit Waghmode <ranjit.waghmode@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change the dtsi include code to use the C pre-processor #include instead
of the device tree /include/. This brings all ZynqMP device trees inline
with each other.
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move kernel and fdt offsets and sizes to board config file
as the flash size varies across boards
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing adv7511 and configure to match Base TRD.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Reviewed-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- Have compatible string as the first property
- Sync with Linux kernel dtsi
- Add missing interrupt properties
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added addtional bindings required for FPGA Manager operation
of the Xilinx Zynq Devc configuration interface.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
GPIO driver supports an input interrupt that's why gpio node itself can
be labeled as interrupt controller.
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Unlock current sector instead of sector 0 before buffered write.
[Patch subject and commit text slightly reworded, Stefan]
Signed-off-by: Rouven Behr <u-boot@behr-iss.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This line is not needed, as the board supports DT based probing. And
here the "Model:" is already printed:
Model: Marvell Armada XP theadorable
Board: theadorable
One line for the board name is enough.
Signed-off-by: Stefan Roese <sr@denx.de>
Sometimes the PCIe link for the PEX-switch will not come-up. In this case,
the board is not in a usable state. This patch makes sure that in this
case a soft-reset is issued. If this soft-reset does not result in the
PEX-switch being detected after some soft-reset cycles, an I2C message
is sent to the uC to issue a complete power-cycle of the board.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds bootcount support to the MVEBU theadorable board. Since
no reset-safe registers seem to be available, it uses the last 4KiB
of SDRAM for the bootcounter location.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds an USB power toggle for theadorable. Additionally, the
USB PHY RX Channel Control 0 Register is changed to fix some issues
noticed while accessing some specific USB sticks.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the missing configuration of the output value to the
gpio_direction_output() function. Without this, calling
gpio_direction_output() does not set the out-value at all and only
configures the gpio as output.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Reviewed-by: Kevin Smith <kevin.smith@elecsyscorp.com>
The Orange Pi One SBC, is a stripped down version of the popular
Orange Pi PC. The one is a H3 based SBC, with 512M of RAM,
micro-sd slot, 1 host usb, 1 otg usb, hdmi and 100Mbit ethernet.
The dts is identical to the dts submitted to the upstream kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
On the H3 we need to enable the clk and de-assert the reset of the
companion to be able to talk to the actual usb host controller.
Before this commit we were also disabling the companion clk-gate /
asserting its reset on remove, causing the later remove callback of
the companion itself to (sometimes) fail with:
ERROR: USB HC reset timed out!
This commit fixes this by not disabling the companion's clk-gate nor
asserting its reset on remove.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We have CONFIG_CMD_GPIO=y in almost all sunxi boards, but after
its Kconfig conversion it has ended up missing on some recently
added boards.
Simply select it for ARCH_SUNXI, so that we get it on all
sunxi boards for both a consistent user experience and simpler
defconfig files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
DLDO3 is used to provide Port-D power and PD is used for the
usb-hub / sata-5v enable pins. The 2.5V comes from the schematic
and matches the factory image fex file.
The dts changes are the minimal changes needed for u-boot to
pick-up the usb host controllers. The upstream kernel does not
(yet) have usb host support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the value used in the fex file of the manufacturer images,
and also the DCDC1 default. Sometimes lower values are used to save
battery power, but that does not apply to a SBC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>