To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This commit add the support in u-boot to read the IV
in the FIT image instead of u-boot device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Currently FIT image must be signed by all required conf keys. This means
Verified Boot fails if there is a signature verification failure
using any required key in U-Boot DTB.
This patch introduces a new policy in DTB that can be set to any required
conf key. This means if verified boot passes with one of the required
keys, U-Boot will continue the OS hand off.
There were prior attempts to address this:
https://lists.denx.de/pipermail/u-boot/2019-April/366047.html
The above patch was failing "make tests".
https://lists.denx.de/pipermail/u-boot/2020-January/396629.html
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the previous patch, net_init now exposes some errors, so check for
them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver interferes with other sandbox tests since it causes log output
to be interspersed with "No ethernet found." messages. Disable this driver
by default.
Enable it for the syslog tests so that they still pass.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all log devices are enabled by default. Add a function to allow
devices to be disabled or enabled at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is no way to disable a log driver. But the syslog driver
causes (attempted) network traffic in sandbox every time a log message
is printed, which is often.
Add a flag to enable a log driver. Adjust struct log_device to use a short
for next_filter_num so that no more memory is used for devices. Also fix
a missing line in the struct log_driver comment while here.
To maintain compatibility, enable it for all drivers for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if CONFIG_LOG enabled, putting LOG_DEBUG at the top of a file
(before log.h inclusion) causes _log() to be executed for every log()
call, regardless of the build- or run-time logging level.
However there is no guarantee that the log record will actually be
displayed. If the current log level is lower than LOGL_DEBUG then it will
not be.
Add a way to signal that the log record should always be displayed and
update log_passes_filters() to handle this.
With the new behaviour, log_debug() will always log if LOG_DEBUG is
enabled.
Move log_test_syslog_nodebug() into its own file since it cannot be made
to work where it is, with LOG_DEBUG defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
This relates to booting since it is the default devicetree provided to
Linux. Move it under the 'boot options' menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a number of miscellaneous boot images at the top level of the
kconfig menu. Move these into the 'boot options' menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the autoboot options are in cmd/Kconfig but they don't really
relate to commands. They relate to booting, so move this menu under the
boot menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most of the boot options are in common/Kconfig but that file is already
extremely large. Create a new Kconfig.boot to hold the boot options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some blobs need a larger alignment than the default. For example, ACPI
tables often start at a 4KB boundary. Add support for this.
Update the size of the test blob to allow these larger records.
Signed-off-by: Simon Glass <sjg@chromium.org>
The intention which bloblists is that each blob's data is aligned in
memory. At present it is only the headers that are aligned.
Update the code to correct this and add a little more documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to be able to see basic statistics about the bloblist and
also to list its contents. Add a 'bloblist' command to handle this.
Put the display functions in the bloblist modules rather than in the
command code itself. That allows showing a list from SPL, where commands
are not available.
Also make bloblist_first/next_blob() static as they are not used outside
this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move call to optee_copy_fdt_nodes() introduced by commit 6ccb05eae0
before generic changes in kernel FDT so that platform specific changes
are not overridden by the changes made by this function.
Fixes: 6ccb05eae0 ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The 44758771ee commit removes CONFIG_PREBOOT but actually sets the USE_PREBOOT
Kconfig option which isn't CONFIG_PREBOOT and is also a bool option which means
we regress because 'usb start' isn't run when expected, it should also be run
for devices that have USB storage because keyboards aren't the only thing we
might need the USB bus for.
Fixes: 44758771ee ("arm: move CONFIG_PREBOOT="usb start" to KConfig")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jonas Smedegaard <dr@jones.dk>
Cc: Neil Armstrong <narmstrong@baylibre.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
ATF support was all the time based on FIT image support but this dependency
is not recorded anywhere.
For !SPL_FIT && SPL_ATF there is compilation error:
common/spl/spl.c: In function 'board_init_r':
common/spl/spl.c:689:26: error: 'struct spl_image_info' has no member named 'fdt_addr'
689 | spl_fixup_fdt(spl_image.fdt_addr);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a message is written by a log driver (e.g. via the network stack) this
may result in the generation of further messages. We cannot allow these
additional messages to be emitted as this might result in an infinite
recursion.
Up to now only the syslog driver was safeguarded. We should safeguard all
log drivers instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In bootm_load_os() the OS image is decompressed. In later stages of the
boot process we need the decompressed size of the image.
Update images->os.image_len after decompression.
Passing the correct size is necessary if we want to check loaded EFI
binararies for file truncation by comparing the loaded size to the header
field SizeOfImage.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kconfig provides several config options for setting up default variables
but these are unused when variables are passed to U-Boot via file.
That's why cover this dependency in Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The environment variable loadaddr is in the virtual address space of the
sandbox. To get the actual memory address where the FIT image has been
loaded we have to convert this address according to the memory mapping of
the sandbox.
Equally the addresses in the *.its file have to be converted when used in
the dfu_ram driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
%s/parameteres/parameters/g
Even if a line exceeds 80 characters we should not split output strings
to make debugging easier.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When board_get_usable_ram_top() limits gd->ram_top, env_get_bootm_size()
must not exceed that limit. Otherwise, boot_relocate_fdt() might put fdt
out of the allowed RAM range.
The similar commit 8ce1f10cf2 ("ARM: bootm: take into account
gd->ram_top") exposed this bug.
This fixes boot on Armada 8040 based Clearfog GT-8K where ram_top is set
to 0x80000000 (2GB), but bi_dram[0].size might be up to 0xc0000000
(3GB). Note the relocated fdt address (0xbfff4000) in the console output
listed below:
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
62 bytes read in 21 ms (2 KiB/s)
1: linux
Retrieving file: /extlinux/Image
13740544 bytes read in 1266 ms (10.4 MiB/s)
Retrieving file: /extlinux/armada-8040-clearfog-gt-8k.dtb
33368 bytes read in 31 ms (1 MiB/s)
Booting using the fdt blob at 0x4f00000
Loading Device Tree to 00000000bfff4000, end 00000000bffff257 ... "Synchronous Abort" handler, esr 0x96000045
elr: 000000000006e1cc lr : 0000000000068fd8 (reloc)
elr: 000000007ffa91cc lr : 000000007ffa3fd8
x0 : ffffffffffffffff x1 : 00000000bfffc258
x2 : 0000000000000000 x3 : ffffffffffff7da7
x4 : 0000000004f08258 x5 : 00000000bfff4000
x6 : 00000000bfff4000 x7 : 000000000000000f
x8 : 000000007fb23bf8 x9 : 0000000000000008
x10: 00000000bffff257 x11: 00000000bffff257
x12: 0000000000000000 x13: fffffffffffff000
x14: 00000000bfff4000 x15: 0000000000000021
x16: 000000007ff7bc38 x17: 0000000000000000
x18: 000000007fb2add0 x19: 00000000bfff4000
x20: 0000000004f00000 x21: 000000000000b258
x22: 0000000058820000 x23: 0000000000000010
x24: 000000007ffe3c40 x25: 000000007fb23cb8
x26: 00000000c0000000 x27: 0000000000000000
x28: 000000007fc3fd50 x29: 000000007fb23bd0
Code: 54000061 aa0603e0 d65f03c0 38606882 (38206822)
Resetting CPU ...
Thanks to Patrice CHOTARD who directed me to the right way.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Remove the bi_memstart / bi_memsize assignment in setup_bdinfo() and
make sure, that bd_dram[] is always configured in the weak default
implementation of dram_init_banksize(), when CONFIG_SYS_SDRAM_BASE is
not set.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Use only gd->ram_base/_size in env_get_bootm_size() instead of bi_dram[]
in some cases and bi_memstart in others.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
AVB only uses CONFIG_FASTBOOT_BUF_ADDR from fastboot for memory.
This memory is used for assigning temporary buffers.
This can be assigned a new variable and used as CONFIG_AVB_BUF_ADDR.
This is to support future boards that support AVB but dont support
USB and therefore dont support FASTBOOT.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Cc: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
[trini: Change defaults]
Signed-off-by: Tom Rini <trini@konsulko.com>
binman fixes for portage
various minor fixes
'bind' command improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9BbZcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZZiQf/UVsriftmxdDz3Lvbz7Jw6UCBXbeM3UN8
KgRxVll3kurZeu8bIcjAPY4YRrbWRqSXmZTXpZWgbyZzHLM4RnkamY3KF3DoxPjc
cbskd/fr4nPjSZVFrkzrvD+D5bhm+VrMtf861AkbAqqpG+Q1FmWHgApqOL1fXn3s
2VoMxRz8Cn9KkSDmxaCtJnLX77GVYYdfgii7RuNWGDqr3eBWrzflV38VbPHLplEg
VLqaLBe3G4zVwElA9Nc2hXpZB84KZEETHcBnmCzNkrSYTN2ofvSeZrWbtRztQFhz
yKur1y7jFsryRkMfxBzgldsKFRNnPT9vr+0qGtrztHjCmvhDkx1YMg==
=iDRJ
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22aug20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
replace devfdt_get_addr_ptr() with dev_read_addr_ptr()
binman fixes for portage
various minor fixes
'bind' command improvements
