The only board using this driver is the Freescale MPC8610HPCD board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added board_eth_init() function to bf537-stamp board.
Removed initialization for the Blackin EMAC driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
PCI I/O space is currently mapped 1:1 at 0xFA000000. Linux requires
PCI I/O space to start at 0 on the PCI bus. This patch maps PCI I/O
space such that 0xFA000000 in the processor's address space maps to 0
on the PCI I/O bus.
Signed-off-by Randy Vinson <rvinson@mvista.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
fix mvBL-M7 config and move to matrix_vision subdir
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add the ability for the MPC8349EMDS to run in PCI Agent mode, acting as a
PCI card rather than a host computer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
fix build warnings @ mvBC-P board by using correct types, i.e. change
out_be32 to out_be16 and out_8 accordingly.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: Mark Jackson <mpfj@mimc.co.uk>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset. I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Fixing leading white spaces
- Fixing indentation where 4 spaces are used instead of tab
- Removing C++ comments (//), wherever I introduced them
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
A lot changed in the Linux MTD code, since it was last ported from
Linux to U-Boot. This patch takes U-Boot NAND support to the level
of Linux 2.6.22.1 and will enable support for very large NAND devices
(4KB pages) and ease the compatibility between U-Boot and Linux
filesystems.
This patch is tested on two custom boards with PPC and ARM
processors running YAFFS in U-Boot and Linux using gcc-4.1.2
cross compilers.
MAKEALL ppc/arm has some issues:
* DOC/OneNand/nand_spl is not building (I have not tried porting
these parts, and since I do not have any HW and I am not familiar
with this code/HW I think its best left to someone else.)
Except for the issues mentioned above, I have ported all drivers
necessary to run MAKEALL ppc/arm without errors and warnings. Many
drivers were trivial to port, but some were not so trivial. The
following drivers must be examined carefully and maybe rewritten to
some degree:
cpu/ppc4xx/ndfc.c
cpu/arm926ejs/davinci/nand.c
board/delta/nand.c
board/zylonite/nand.c
Signed-off-by: William Juul <william.juul@tandberg.com>
Signed-off-by: Stig Olsen <stig.olsen@tandberg.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Correct the mx31_gpio_mux() function to allow changing all i.MX31 IOMUX
contacts instead of only the first 256 ones as is the case prior to
this patch.
Add missing MUX_* macros and update board files to use the new macros.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
The recent change to move the .bss outside of the image gives older
binutils (ld from eldk4.1/binutils-2.16) some headache:
ppc_85xx-ld: u-boot: Not enough room for program headers (allocated 3, need 4)
ppc_85xx-ld: final link failed: Bad value
We workaround it by being explicit about the program headers and not
assigning the .bss to a program header.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Sequoia board has two UARTs in "4-pin" mode. This patch modifies the GPIO
configuration to match the schematic, and also sets the SDR0_PFC1 register to
select the corresponding mode for the UARTs.
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the Favr-32 board made by EarthLCD.
This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.
Signed-off-by: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
