This renames the odroid-c2 to p200 and set it as the default GXBB board
Other boards (odroid-c2 and nanopi-k2) will inherit from p200
Signed-off-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcrEcDAAoJEB6zHgIOrC/I1dgH/3mHQNW8bqiNCJYcoVQdheHb
e06TqbWHNlOG/NilYybvdeF+LjeCqhX4PzyL/sdcyBf3D/tK4cVvHpZrQyjb2s6K
5IZSKJ+cZznmq6Hv7b//d30Azhx8bi8luxs60kkj+PF0xI1EyU3JteUqAs4Ooxd7
z+HdcRFuAaps6sy0+szB3fTw9HTGrhFvQuHasDGb2uahhpwGzu/P0RchIDksOdzH
3L4EOvgq8MZCiZ3ZtFWMWzQoCjcKf5Fuux41qar8gG/LrkWRfKG+LfWfZtTiTsjf
vC9bYWmdKtkSLFj1PWgLBfGxev5zwPUbqI2EP4OlagfNs3os5pVFCYV5NZ6ovdE=
=kMXf
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.07 cycle
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Migrate the following options to CONFIG_DM:
CONFIG_DM_GPIO
CONFIG_DM_MMC
CONFIG_DM_ETH
CONFIG_DM_SERIAL
CONFIG_DM_USB
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
This patch moves all instances of static "watchdog_dev" declarations to
the "data" section. This may be needed, as the BSS may not be cleared
in the early U-Boot phase, where watchdog_reset() is already beeing
called. This may result in incorrect pointer access, as the check to
"!watchdog_dev" in watchdog_reset() may not be true and the function
may continue to run.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
After building ATF it is needed to copy the generated bl31.bin file to
the U-Boot source tree.
Make this step explicit in the instructions.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Since commit 9e3c0174da ("pico-imx7d: Add LCD support") we started to
notice some hangs in U-Boot.
There is not an issue on such commit per se, but due to the LCD support
the current drawn is increased and this may cause issues when powering
pico-imx7d-pi from USB.
Some computers may be a bit strict with USB current draw and will
shut down their ports if the draw is too high.
The solution for that is to use an externally powered USB hub between the
board and the host computer.
Add such recommendation to the README file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the DM_MMC conversion the following eMMC boot error is observed:
U-Boot SPL 2019.04-rc4 (Mar 20 2019 - 18:53:28 +0000)
Trying to boot from MMC1
MMC Device 0 not found
spl: could not find mmc device 0. error: -19
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
This happens because the SPL code does not initialize the SDHC pins
and clock.
Fix it by moving the original eMMC initialization from U-Boot proper
to SPL.
Reported-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
The I2C bus number to access the PMIC is I2C 7, fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PHY LED mode register mask should be 0xc000 , not 0xc0000.
Correct the mask to operate on the right bits.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7794_ETHERNET_B config option is unused and based on the
description, this is a setting which should be fully done on a
DT level instead. Remove this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
I took over maintainership from Alex Graf with commit
3157bbfa18 ("rpi: Make Matthias maintainer")
But I forgot to update the board maintainer file.
This patch adds myself to the game.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
On AXS10x boards we have non-standard NAND controller
which was never really used a lot as there're other much more
convenient [as they are standard & removable] persistent media
like SD-card and USB mass storage.
Moreover after recent changes we face with some NAND controller
runtime issues. So instead of keeping support of yet another
non-standard peripheral we're dropping its support for good.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED
I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Define the function board_spi_cs_gpio only when needed,
only called in drivers/spi/mxc_spi.c.
That avoid compilation issue for tqma6s_wru4_mmc_defconfig
when CONFIG_SF_DEFAULT_BUS and CONFIG_SF_DEFAULT_CS are not
defined (CMD_SF not defined) after migration in KConfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When these were moved from mach-omap2 to board files they got placed
inside TI_SECURE_DEVICE ifdef block, they are not secure only, move
them up and out.
Fixes: 413b90777f ("ti: fastboot: Move weak overrides to board files")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Barrier transactions from CCI400 need to be disabled till
the DDR is configured, otherwise it may lead to system hang.
The patch adds workaround to fix the erratum.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Now that we are representing the MDIO mux in LX2160AQDS board in
producer/consumer terms, the consumer nodes' has been changed.
Therefore, modify the device tree fixups according to change in device
tree.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The information in the SabreLite README is inaccurate and sparse. The
upstream U-Boot can boot the SabreLite from SPI-NOR. Additionally, the
freely available imx_loader tool can be easily used to boot a board with a
corrupted SPI, the official Freescale/NXP manufacturing tools are not
required.
Reformat the document, adding a description of how to boot from SPI-NOR
and adding a brief description of how to recover the board should the
SPI-NOR be corrupted using imx_loader.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
The third parameter of the pmic_clrsetbits() function is the mask
to the register and the correct mask is 1 not 0.
Since the LDOGCTL only contains a single valid bit (bit 0),
we can use pmic_reg_write() and write 1 directly, which fixes
the problem in a simpler way and use the original pmic function
that was used prior to the DM PMIC conversion.
Fixes: 8ba377321c ("arm: imx7s-warp: Convert to DM PMIC")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
There is no need to store the values written to the PMIC inside the
'reg' variable. Make it simpler by writing the values directly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
After DM conversion the I2C and MMC related board codes have been
removed, so remove the corresponding header files as well.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
This patch mostly enables DM drivers in board defconfig and all their
dependencies. Additionally we remove USB code that is on longer
executed after enabling CONFIG_DM_USB. Enable CONFIG_PINCTRL, so we
can get rid of ethernet pin configuration.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Convert to use DM_PMIC for the PFUZE3000. Since this PMIC is
under an I2C bus, conver to DM_I2C as well.
Also, since I2C is not used in SPL, remove CONFIG_SPL_I2C_SUPPORT
to avoid build warnings.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Convert to CONFIG_DM_GPIO.
Also, DM GPIO requires gpio_request() to be called explicitly before
doing any gpio operation, so do as requested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
CONFIG_BOARD_TYPES is necessary for Odroid X/X2/U3 boards to detect
proper revision. However building should succeed even without it.
While moving code around, document also the reference clock selection.
This fixes the build error without CONFIG_BOARD_TYPES:
board/samsung/odroid/odroid.c: In function 'board_usb_init':
board/samsung/odroid/odroid.c:473:8: error: 'gd_t' {aka 'volatile struct global_data'} has no member named 'board_type'
if (gd->board_type == ODROID_TYPE_U3)
^~
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>