The device type was left uninitialized which caused later tests
against DEV_TYPE_UNKNOWN to fail. In the result, "usb part" would
attempt to print information about non-existent devices like this:
=> usb part
print_part of 0
Partition Map for USB device 0 -- Partition Type: DOS
Partition Start Sector Num Sectors Type
1 0 2031616 f8
print_part of 1
## Unknown partition table
print_part of 2
## Unknown partition table
print_part of 3
## Unknown partition table
print_part of 4
## Unknown partition table
=>
By initializing the type as DEV_TYPE_UNKNOWN we avoid all the
"Unknown partition table" messages.
[Note: the "print_part of ?" messages is left over debug code that
will be removed in another patch.]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Given a compatible string and physical address try and find a node that
matches. This is useful when we want to find a specific device node to
update (for example if we have multiple PCI nodes we can use the
physical address to distinguish them when trying to update the device
tree).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This code is extracted out of the Linux Kernel code from
arch/powerpc/kernel/prom_parse.c.
We maintain some of the same structure to support multiple bus types even
though we only have one in the current code. In the future we might want
to translate across a PCI bus and thus it will be easier to add that
functionality back in.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
The board maintainer states:
The GTH board is obsolete and has not been manufactured for
several years.
To my knowledge, no recent U-Boot build has been tested on that
card.
So drop support for this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Acked-by: Thomas Lange<thomas@corelatus.se>
The new command dumps the TLBCAM, the LAWs, and the BR/OR regs.
Add CONFIG_CMD_REGINFO to the config for all MPC85xx parts.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Change if (ok) {
bunch of stuff
} else {
error
}
to
if (error) {
get out
}
proceed with bunch of stuff
Plus a few whitespace cleanups.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is a re-submission of the patch by Harald Welte
<laforge@openmoko.org> with minor modifications for rebase and changes
as suggested by Scott Wood <scottwood@freescale.com> [1] [2].
This patch enables the environment partition to have a run-time dynamic
location (offset) in the NAND flash. The reason for this is simply that
all NAND flashes have factory-default bad blocks, and a fixed compile
time offset would mean that sometimes the environment partition would
live inside factory bad blocks. Since the number of factory default
blocks can be quite high (easily 1.3MBytes in current standard
components), it is not economic to keep that many spare blocks inside
the environment partition.
With this patch and CONFIG_ENV_OFFSET_OOB enabled, the location of the
environment partition is stored in the out-of-band (OOB) data of the
first block in flash. Since the first block is where most systems boot
from, the vendors guarantee that the first block is not a factory
default block.
This patch introduces the 'nand env.oob' command, which can be called
from the u-boot command line. 'nand env.oob get' reads the address of
the environment partition from the OOB data, 'nand env.oob set
{offset,partition-name}' allows the setting of the marker by specifying
a numeric offset or a partition name.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/43916
[2] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/79195
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Acked-by: Harald Welte <laforge@gnumonks.org>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Instead of defining the flags sevaral times in different source files
(which is error prone), move them to a central place in a header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Change the return type of the *printf() functions to the standard
"int"; no changes are needed but returning the already available
length count.
This will save a few additional strlen() calls later...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Remove some INFERNO related #ifdef's from common environment code by
fixing the board configuration settings (add CONFIG_ENV_SECT_SIZE).
While we are at it, fix comment which incorrectly talks about 4 KB
environment size, while it's actually 0x4000 = 16 KiB.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Rolf Offermanns <rof@sysgo.de>
This patch adds redundant environment for environment in SPI flash.
I took env_flash.c as an example and slightly modified it. Apart
from adapting things to SF, I also slightly changed the decision
logic to use area 2 as a default in case the flags are wrong because
not having a default path worried me.
I did not add a section for CONFIG_ENV_IS_IN_SPI_FLASH in environment.h
because I did not understand if this is desired and/or needed.
So to use the feature, one has to set CONFIG_ENV_OFFSET_REDUND _and_
CONFIG_SYS_REDUNDAND_ENVIRONMENT.
I checked it by powering off my board several times during flash
erase or write, because I do not know if there are other stress
test scenarios.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
AVR32 case was missing in cmd_bdinfo, resulting in compiler warning
(bd->bi_baudrate declared unsigned int at AVR32, but printf used %d)
At the same time slightly reordered #if #elif #endif to make ARM one
of the cases and not an extra case surrounding all others
Signed-off-by: Reinhard Meyer <info@emk-elektronik.de>
Tested-by: Andreas Biemann <biessmann@corscience.de>
For the following hwconfig string:
key1:subkey1=value1,subkey2=value2;key2:value3
The subkey2 cannot be extracted correctly. The parsing code looks
for comma as a stopch, but there may be two kind of stop characters:
a comma and a semicolon.
Currently the code would return "value2;key2:value3", while just
"value2" is the correct answer.
This patch fixes the issue by making the code aware of multiple
stop characters.
For old U-Boots, the issue can be workarounded by placing a comma
before a semicolon, i.e.:
hwconfig=key1:subkey1=value1,subkey2=value2,;key2:value3
Reported-by: York Sun <yorksun@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
The console_buffer size is declared in common/main.c as
-- char console_buffer[CONFIG_SYS_CBSIZE + 1];
so this extern definition is wrong.
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Add sec3.1 h/w geometry for fdt node fixups.
Also, technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it. Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SPD has minor change from Rev 1.2 to 1.3. This patch enables Rev 1.3.
The difference has ben examined and the code is compatible.
Speed bins is not verified on hardware for CL7 at this moment.
This patch also enables SPD Rev 1.x where x is up to "F". According to SPD
spec, the lower nibble is optionally used to determine which additinal bytes
or attribute bits have been defined. Software can safely use defaults. However,
the upper nibble should always be checked.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable the auto completion (with TAB) of the environment variable name
after the editenv command.
Signed-off-by: Ralf Trbenbach <ralf.truebenbach@men.de>
On the fly also fixed the following things:
- write help talked about a parameter oob, but that one was not used, so
removed it from the help message.
- the test command also allowed a force subcommand but didn't use it.
eliminated the code.
- do_onenand made static
- do_onenand contained
int blocksize;
...
mtd = &onenand_mtd;
this = mtd->priv;
blocksize = (1 << this->erase_shift);
As blocksize was not used the last two statements were unneeded so
removed them.
The first statement (mtd = ....) assigns to a global. Not sure if it
is needed, and since I could not test this, left the line for now
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The "mtdparts add" command wrote through a NULL pointer - on many
systems this went unnoticed (PowerPC has writable RAM there, some ARM
systems have ROM where a write has no effect), but on arm1136
(i.MX31) it crashed the system.
Add appropriate checks.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Extend mpc512x serial driver to support multiple PSC ports.
Subsequent patches for PDM360NG board support make use of this
functionality by defining CONFIG_SERIAL_MULTI in the board config
file. Additionally the used PSC devices are specified by defining
e.g. CONFIG_SYS_PSC1, CONFIG_SYS_PSC4 and CONFIG_SYS_PSC6.
Support for PSC devices other than 1, 3, 4 and 6 is not added
by this patch because these aren't used currently. In the future
it can be easily added using DECLARE_PSC_SERIAL_FUNCTIONS(N) and
INIT_PSC_SERIAL_STRUCTURE(N) macros in cpu/mpc512x/serial.c.
Additionally you have to add code for registering added
devices in serial_initialize() in common/serial.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
* add WATCHDOG_RESET to !tstc() loops
* prevents watchdog timeout, while waiting for input,
if CONFIG_BOOT_RETRY_TIME or CONFIG_SHOW_ACTIVITY defined
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
gcc 3.4.6 previously reported the following error on many MIPS boards
which utilize UBI:
cmd_ubi.c:193: warning: 'vol' might be used uninitialized in this function
The current code is structured such that 'vol' will never be used when
it is NULL anyway, but gcc isn't smart enough to figure this out.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
While debugging one ill behaving USB device I found two bugs in USB
storage probe.
usb_stor_get_info() returns -1 (error), 0 (skip) or 1 (ok). First part
of this patch fixes error case.
Second part fixes usb_inquiry()'s retry counter handling. Original code
had retry = -1 on error case, not retry = 0 as checked in the next line.
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Here's another USB storage patch. Currently U-Boot handles storage
devices #0 - #4 as valid devices, even if there is none connected. This
patch fixes usb_stor_get_dev() to check detected device count instead
of MAX-define.
This is very important for ill behaving devices. usb_dev_desc[] can be
partially initialized if device probe fails.
After fixing get_dev() it was easy to fix "usb part" etc commands.
Previously it outputed "Unknown partition table" five times, now it's
"no USB devices available".
Signed-off-by: Kim B. Heino <Kim.Heino@bluegiga.com>
Add a helper function that given an alias will delete both the node
the alias points to and the alias itself
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Booting a "Multi-File Image" including a linux kernel, ramdisk and
fdt, generated with
mkimage -A ppc \
-O linux \
-T multi \
-C gzip \
-a 00000000 \
-e 00000000 \
-n "kernel-2.6+initrd+dtb" \
-d "vmlinux.bin.gz:ramdisk_image.gz:board.dtb" \
multi.bin
actually fails, because ramdisk start and end addresses
didn;t get initialized. This patch fixes this issue.
Tested on the KUP4K board.
Signed-off-by: Heiko Schocher <hs@denx.de>
The code to parse alen appeared 6 times in the function.
Factored this out in a small helper function
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
This fixes the following warnings when running MAKEALL for coldfire :
cmd_bdinfo.c:354: warning: 'print_eth' defined but not used
Signed-off-by: Philippe De Muyter <phdm at macqel.be>
Support for 16bpp was supposed to be in the code but was not working.
This makes it work and has been tested in the nhk8815 board.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
When issuing a nand scrub command, the entered character is not displayed
this may be confusing. This patch makes the input character being
displayed if it is a 'y' so that an user knows he is about to scrub his
nand.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Allow overwriting defined partitions in the device tree blob
using partition info defined in the 'mtdparts' environment
variable.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Gerald Van Baren <vanbaren@cideas.com>
Match history buffer size to console buffer size. History buffer size
was hard coded to 256, artificially limiting the command buffer size.
The history buffer now tracks CONFIG_SYS_CBSIZE.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
When CONFIG_SYS_CBSIZE equals MAX_CMDBUF_SIZE, a command string of
maximum length will overwrite part of the history buffer, causing the
board to die. Expand the console_buffer and hist_lines buffer by one
character each to hold the missing NULL char.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
This patch add functionality to use memory addresses in expressions.
This increases the power of expressions substantially
It adheres to the standard convemtions: memory addresses can be given
in the format *address (e.g. *1000)
Rationale for this change is that it allows masking off bits from a
byte that is obtained by reading data from e.g. i2c.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Fix warning: control reaches end of non-void function
Signed-off-by: Wolfgang Denk <wd@denx.de>
according to some of the comments the subaddress length is 1 or 2, but we are being
prepared for the case it becomes 3. However the code also accepted 4.
This repairs this by changing the constand 4 to 3.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
If a board uses cfb_console driver and splash image
and also defines CONFIG_SILENT_CONSOLE, the user is
locked out even if "silent" is not set. It is not
possible to get any output, neither on vga console
device nor on serial console after redirecting the
output to the serial console, since the GD_FLG_SILENT
flag remains set.
Fix the problem by redirecting the output from frame
buffer to serial console if splashimage is used.
Only suppress the output if "silent" environment
variable was set and don't set the GD_FLG_SILENT
flag arbitrarily.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch removes the \n after the help message for mmcinfo.
This resulted in an empty line being displayed after the mmcinfo line
when the help command was given.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
The length of configured MTDPARTS_DEFAULT string
could be greater than console printbuffer size.
Replace printf() by puts() to avoid potential buffer
overflows.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The auto-update feature (CONFIG_UPDATE_TFTP) requires that the env
variable serverip be set for the TFTP access. If DHCP is to be used
to get the serverip env variable, this doesn't work as DHCP happens
after the auto-update attempt has run. A solution is to run DHCP in
PREBOOT, but even this is too late.
To solve this, we move update_tftp() below the PREBOOT stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch uses gd->relocaddr variable to store uboot's relocated
address in RAM and shows it in bdinfo command.
This patch moves CONFIG_AMIGAONEG3SE style copying of the address
in board_init_f to just before relocation is actually done.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Tested-by: Detlev Zundel <dzu@denx.de>
fix pointer dereferencing
if the size is .b and .w an 8 or 16 bit access is done.
Signed-off-by: Frans Meulenbroeks <fransmeulenbroeks@gmail.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This patch fixes a problem I've notived on a buggy PPC4xx system. This
system has problems with the PHY MDIO communication and seemed to be
stuck/crashed in miiphy_reset(). But degugging revealed, that the CPU
didn't crash, but "only" hung in this counting loop for about 2 minutes.
This patch now uses a real timeout of 0.5 seconds (as mentioned in the
comment in miiphy_reset).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch changes usb_control_msg back to the state prior to commit
4886720844.
The USB driver ISR routine may update the status.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Fix compile error:
cmd_ximg.c: In function 'do_imgextract':
cmd_ximg.c:234: error: 'i' undeclared (first use in this function)
cmd_ximg.c:234: error: (Each undeclared identifier is reported only once
cmd_ximg.c:234: error: for each function it appears in.)
Signed-off-by: Wolfgang Denk <wd@denx.de>
Not all boards defining LCD_COLOR16 are able to set
lcd_color_fg/lcd_color_bg correctly. The issue seems to
be caused by CONFIG_ATMEL_LCD ifdefs in lcd_setfgcolor()
and lcd_setbgcolor(). Actually, the color values passed
to these functions are already correct, we don't need
to fix them. So remove ifdefs here.
Reported-by: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
env_nand.c would crash silently if a malloc() for the environment
buffers failed; make it print an error message and fail gracefully,
i. e. use the default environment then.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: John Rigby <jcrigby@gmail.com>
Add a disable sub-command to the cpu command that allows for disabling
cores in multicore processors. This can be useful for systems that are
using multicore chips but aren't utilizing all the cores as a way to
reduce power and possibly improve performance.
Also updated an added missing copyright.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
imxtract currently can not handle compressed images. This patch adds
handling for bzip2 and zip compression. In both cases, a destination
address has to be specified for extraction.
Signed-off-by: Wolfgang Wegner <w.wegner@astro-kom.de>
Commit b5b004ad8a caused the sector_size to
be calculated incorrectly when the part size was not hardcoded. This is
because the new code relied on part->size but tried to do the calculation
before it was initialized properly, and it did not take into consideration
the magic SIZE_REMAINING define.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
If you really want to slim down U-Boot and you would rather use a higher
compression scheme (like LZMA), it'd be nice to disable gzip/zlib since
these code bases take up a significant amount of space.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch adds support for "imximage" (MX Boot Image)
to the mkimage utility. The imximage is used on the Freescales's
MX.25, MX.35 and MX.51 processors.
Further details under doc/README.imximage.
This patch was tested on a Freescale mx51evk board.
Signed-off-by: Stefano Babic <sbabic@denx.de>
cramfsls and cramfsload are added to the command list.
A cramfs placed at 'cramfs_addr' can the be listed with 'cramfsls' and files
can be loaded with 'cramfsload'. 'cramfs_addr' is an environment variable
specifying the address the cramfs is located.
This works for powerpc and for ARM.
Use CONFIG_CMD_CRAMFS.
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add redundant environment support for environment lying on a EEPROM.
Tested on uppcoming suen3 support
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
- CONFIG_ENV_EEPROM_IS_ON_I2C
define this, if you have I2C and SPI activated, and your
EEPROM, which holds the environment, is on the I2C bus.
- CONFIG_I2C_ENV_EEPROM_BUS
if you have an Environment on an EEPROM reached over
I2C muxes, you can now define, how to reach this
EEPROM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Current code uses the second argument to bootm for standalone images to
override the load address specified in the image instead of passing all
parameters as is to the application. This behaviour is not documented
and not in line with how the go command works for standalone applications,
so we simply drop it.
Signed-off-by: Detlev Zundel <dzu@denx.de>
In case we boot an image marked as 'standalone' and 'linux', the current
code erroneously tried to load a ramdisk.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Convert the funcs to do the conversion inline so that we can do the copy
all at once with memcpy. This let's us push out an weird arch-specific
issue with accessing different regions of memory to the memcpy function
like the MMRs on Blackfin systems, and it should be a bit faster.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default kgdb functions can be implemented with common U-Boot functions,
so rather than force everyone to copy & paste these things, create a set of
weak stubs.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are a bunch of features in U-Boot that we want to enable by default,
and it's best if we centralize them in one place rather than updating all
the board files out there.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>