This change fixes the compiler warning
main.c: In function 'abortboot':
main.c:122: warning: too few arguments for format
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This change fixes the compiler warning
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF
for correct output!
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This sets CONFIG_SYS_HZ to 1000 for all boards that use the s3c2400 and
s3c2410 cpu's which fixes various problems such as the timeouts in tftp being
too short.
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't
have any s3c2400 or s3c2410 boards but need this patch applying before I can
submit patches for the SBC2440-II Board. Also, ran MAKEALL for all ARM9 targets
and no new warnings or errors were found.
It was originally submitted on 21/06/2009 but didn't get into the 2009.08
release, and Jean-Pierre made one comment on the original patch (see
http://lists.denx.de/pipermail/u-boot/2009-July/055470.html). I've made two
changes to the original patch:
- it's been re-based to the current release
- I've re-named get_timer_raw() to get_ticks() in response to Jean-Pierre's comment
This affects the sbc2410, smdk2400, smdk2410 and trab boards. I've copied it
directly to the maintainers of all except the sbc2410 which doesn't have an
entry in MAINTAINERS.
Signed-off-by: Kevin Morfitt <kmorfitt@aselaptop-1.localdomain>
Tested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adds new board SMDKC100 that uses s5pc100 SoC
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: HeungJun, Kim <riverful.kim@samsung.com>
This patch implements several updates:
-disable CONFIG_ENV_OVERWRITE
-add new hardware style variants and set the arch numbers appropriate
-pass the serial# and hardware revision to the kernel
-removed unused macros from include/configs/meesc.h
-fixed multiline comment style
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add setup for ethernet on Tobi, allowing kernel/ramdisk to be loaded
over tftp.
This also refactors the smc911x driver to allow for detecting when the
chip is missing. I.e. the detect_chip() function is called earlier and
will abort gracefully when the Chip ID read returns all 1's.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Ben Warren <biggerbadderben@gmail.com>
This changes fixes an early i2c error.
It appears that I2C is working because once a read or write
error is detected, the omap24xx_i2c driver calls i2c_init
inside its error handling check.
While it is ok to attempt error handling this way, the boards
must not depend on this side effect to initialize it's i2c.
Instead of explicitly calling i2c_init for every board, use
the generic arm initialization in lib_arm/board.c. By defining
the config variable CONFIG_HARD_I2C, the omap3 i2c initialization
is included in the init_sequence table.
Run tested on Beagle.
Compile tested on the omap3's
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
The implementation is borrowed from the sheevaplug board and the Marvell
1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA.
Signed-off-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
these boards are built around Atmel's AT91SAM9260/9G20 and have
up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND
and include a 10/100 Ethernet PHY in RMII mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR
flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII
mode.
Signed-off-by: Eric Benard <eric@eukrea.com>
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag.
This is already included when we include the
config_cmd_default.h header file. So this flag is removed.
Also another flag to enable NAND functions was being
enabled incorrectly.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch does the following
1) Enables the NAND driver which is now available.
2) Enables the 'CONFIG_MTD_DEVICE' as without this the
compilation will fail
3) We now have a safe place to store environment and defines
an offset where this can be stored. This offset value is such that it is after
the location where U-Boot is flashed using TI flash utilities.
4) Enables Bootdelay
5) Increases malloc() arena size. Manufacturers are coming out with
NAND with large blocks sizes of upto 1 MiB. It has been noticed that
as the block size of the NAND used is increased, if this particular
value is not increased, the NAND driver will output out of memory
errors.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The Default mode that is built for the Davinci DVEVM happens
to be the NOR mode.
When we want to build for the NAND mode, we get a compilation
error. This is overcome by defining the CONFIG_MTD_DEVICE
flag in the NAND mode.
The image built for NAND mode was successfully tested on the
DaVinci DM6446 EVM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch removes the asm/sizes.h header file from being
included in the DaVinci SOC configs.
References to SZ_xx have been replaced by appropriate
bit shifted values.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Wolfgang Denk <wd@denx.de>
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.
The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file. The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>
Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds support to detect the amount of DDR2 SDRAM
on PMC440 modules. Detection is done by probing through
a list of available and supported hardware configurations
from 1GByte down to 256MB.
The static TLB entry is replaced by dynamically created entries.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The Linux kernel has changed the way it numbers serial ports, so update
the default command line to match it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The u-boot image has outgrown the current space and overflowed into the
env sector. So move the env to the next available sector (we've already
allocated the first few sectors anyways for u-boot).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.
The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.
The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.
This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.
When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.
This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.
Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By nature of being based off the MPC8548CDS board, this
board inherited an ENV_SIZE setting of 256k. But since
it has a smaller flash device (8MB soldered on), it has
a native sector size of 128k, and hence the ENV_SIZE was
causing 2 sectors to be used for the environment.
By removing the unused sector, we can push TEXT_BASE up
closer to the end of address space and reclaim that
sector for any other application. This also fixes the
mismatch between TEXT_BASE and MONITOR_LEN reported by
Kumar earlier.
Since this board also supports the ability to boot off
the 64MB SODIMM flash, this change is forward looking
with that in mind; i.e. the settings for MONITOR_LEN
and ENV_SIZE will work when the 512k sectors of the
SODIMM flash are used for alternate boot in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the board config header. This takes advantage of
that for the sbc8349 board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With this patch we can change QE USB mode without need to hand-edit
the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes various ethernet issues with gigabit links handling
in U-Boot. The workarounds originally implemented by Kim Phillips for
Linux kernel.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
Signed-off-by: Heiko Schocher <hs@denx.de>
- As these boards are similiar, collect common config options
in manroland/common.h and manroland/mpc52xx-common.h
for mpc5200 specific common options for this manufacturer.
- add OF support
- update default environment
Signed-off-by: Heiko Schocher <hs@denx.de>
Minor edit of commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Martha M Stan <mmarx@silicontkx.com>
Minor cleanup:
Re-ordered default_mddrc_config[] to have matching indices.
This allows to use the same index "N" for source and target fields;
before, we had code like this
out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]);
which always looked like a copy & paste error because 2 != 3.
Also, use NULL when meaning a null pointer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the boards config header. This takes advantage of
that for the sbc8540/sbc8560 boards.
There were a couple of cheezy comments pointing at incorrect
files, or files that don't exist, so I've cleaned those up too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, and if you had 33MHz PCI, you
had to manually change CONFIG_SYS_NS16550_CLK too, which was
not real user friendly,
This adds the typical PCI and clock speed make targets to the
toplevel Makefile in accordance with what is being done with
other boards (i.e. using the "-t" to mkconfig).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI/PCI-e support for the sbc8548 was based on an earlier
version of what the MPC8548CDS board was using, and in its
current state it won't even compile. This re-syncs it to match
the latest codebase and makes use of the new shared PCI functions
to reduce board duplication.
It borrows from the MPC8568MDS, in that it pulls the PCI-e I/O
back to 0xe280_0000 (where PCI2 would be on MPC8548CDS), and
similarly it coalesces the PCI and PCI-e mem into one single TLB.
Both PCI-x and PCI-e have been tested with intel e1000 cards
under linux (with an accompanying dts change in place)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The size of the LB SDRAM on this board is 128MB, spanning CS3
and CS4. It was previously only being configured for 64MB on
CS3, since that was what the original codebase of the MPC8548CDS
had. In addition to setting up BR4/OR4, this also adds the TLB
entry for the second half of the SDRAM.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The sbc8548 has a 64MB SODIMM flash module off of CS6 that
previously wasn't enumerated by u-boot. There were already
BR6/OR6 settings for it [used by cpu_init_f()] but there
was no TLB entry and it wasn't in the list of flash banks
reported to u-boot.
The location of the 64MB flash is "pulled back" 8MB from
a 64MB boundary, in order to allow address space for the
8MB boot flash that is at the end of 32 bit address space.
This means creating two 4MB TLB entries for the 8MB chunk,
and then expanding the original boot flash entry to 64MB
in order to cover the 8MB boot flash and the remainder
(56MB) of the user flash.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are a couple defines and PCI bridge quirks related to the PCI
backplane of the MPC8548CDS that have no meaning in the context of
the port to the sbc8548 board, so delete them.
Also, the form factor of the sbc8548 is a standalone board with a
single PCI-X and a single PCI-e slot. That pretty much guarantees
that it will never be a PCI agent itself, so the host/agent and root
complex/end node distinctions have been removed.
Similarly, since there is no physical connector mapping to PCI2, so
all references of PCI2 in the board support files have been removed
as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>