This adds base register address of SH QSPI.
Currently, SH QSPI is used only from R8A7790 and R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel
and other.
This disables TMU0 at the request of from kernel user.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On U-boot uses TMU0 as timer, but TMU0 does not use on linux kernel
and other.
This disables TMU0 at the request of from kernel user.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SolidRun has designed the Hummingboard board based on mx6q/dl/solo.
Add the initial support for the mx6 solo variant.
More information about this hardware can be found at:
http://imx.solid-run.com/wiki/index.php?title=Carrier-One_Hardware
(Carrier-One was the previous name of Hummingboard).
Based on the work from Jon Nettleton <jon.nettleton@gmail.com>.
Signed-off-by: Jon Nettleton <jon.nettleton@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Provide an argument to enable_fec_anatop_clock() to specify the clock frequency
that will be generated.
No changes are made to mx6slevk, which uses the default 50MHz fec clock.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
when creating the hashtable, for each environmentvariable
getenv(ENV_CALLBACK_VAR) and getenv(ENV_FLAGS_VAR) is called,
which costs at this point a lot of time. So call this two
getenv() calls only once.
Boottime on the ids8313 board without this patch:
2013-12-19 13:38:22,894: NAND: 128 MiB
2013-12-19 13:38:27,659: In: serial
(~4.8 sec)
Bootime with this patch on the ids8313 board:
2013-12-19 13:40:25,332: NAND: 128 MiB
2013-12-19 13:40:25,546: In: serial
(~0.2 sec)
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wolfgang Denk <wd@denx.de>
For standalone images, bootm had a special case where the OS boot function
was NULL but did actually exist. It was just called manually.
This was removed by commit 35fc84fa which checks for the non-existence of
this function before the special case is examined.
There is no obvious reason why standalone is handled with a special case.
Adjust the code so that standalone has a normal OS boot function. We still
need a special case for when the function returns, but at least we can
avoid the main problem.
This is intended to fix the reported:
ERROR: booting os 'U-Boot' (17) is not supported
but needs testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Issues:
- reading i2c data by passing u16 pointer causes errors in read data.
- max17042 status register fields have not only Power On Reset meaning
so using proper mask is required.
Changes:
- read i2c data to type u32 instead of u16 - avoids buffer overflow
- compare FG status register using mask not just one bit value
- add checking return value to functions fg read/write
- add model lock and model check count
- add debug msg
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Otherwise, when booting VxWorks kernel, the incorrect message will
be seen:
ARM Unknown OS Kernel Image (uncompressed)
Signed-off-by: Miao Yan <miao.yan@windriver.com>
Compiling of full list of commands does not advance the counter,
so it always results in an empty list.
This seems to be (inadvertently?) introduced by commit
6c7c946cad.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Variable uncompressedSize references the space available, while outSizeFull is
the actual expected uncompressed size. Using the wrong value causes LzmaDecode
to return SZ_ERROR_INPUT_EOF. Problem was introduced in commit afca294. While
at it add additional debug message.
Signed-off-by: Antonios Vamporakis <ant@area128.com>
CC: Kees Cook <keescook@chromium.org>
CC: Simon Glass <sjg@chromium.org>
CC: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
CC: Luka Perkov <luka@openwrt.org>
Building some arm boards with older binutils may produce errors like this:
---8<---
crt0.S: Assembler messages:
crt0.S:70: Error: register expected, not '#(184)' -- `sub sp,#(184)'
--->8---
Use canonical version of the subtract mnemonic to avoid those issues.
Reported-by: Alexey Smishlayev <alexey@xtech2.lv>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some targets will build fine but not boot if sections .hash and
.got.plt are not present in the binary. Add them back.
Also, Exynos machines require .machine_param section in SPL.
Add it.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Tested-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Access the OneNAND 1KiB window on the VPAC270 as an SRAM instead of accessing
it as a burst-RAM. This fixes a problem where the board failed to reboot
sometimes as the CPU couldn't start executing from the OneNAND 1KiB window.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
The OneNAND SPL used on PXA is slightly obscure. Due to the OneNAND limitation,
where we have only the first 1KiB of the OneNAND available upon power-up as a
memory-mapped area, from which the CPU starts executing, we place only the most
essential code into this first 1KiB . This code copies the rest of the SPL into
SRAM and jumps to it. This code is stored in section .text.0 .
The rest of the SPL is stored in section .text.1 . When running the OBJCOPY on
the SPL, it will preserve only .text section, but the .text.0 and .text.1 are
stripped away from the result, thus making the SPL binary empty. The patch adds
additional -j parameters to the OBJCOPY for PXA during the SPL build, which will
preserve the .text.0 and .text.1 sections.
Moreover, this patch also adds missing functions into the .text.0 section, since
otherwise the PXA270 with 1KiB-window OneNAND won't be able to boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Before this change ums mode can not be entered when device
was using the same usb port for usb/uart communication.
Switching USB cable from UART to USB always causes ums exit.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.
This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
The controller has 3 ports. The port0 is for USB 2.0 Phy, port1 and port2
are for HSIC phys. The usb 2.0 phy is already being setup. This patch
sets up the hsic phys.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
The fifo size of ep0 is 64 bytes, and if the packet size grater than
64 bytes, the driver would have to fill up the fifo multiple times,
and before filling up the fifo, the driver should make sure the fifo
is empty by checking fifo empty indication.
However there is a hardware bug that the fifo empty indication is
somehow a bit earlier than fifo reset. So if I don't add an extra
delay here, the data might be corrupted. (i.e., 1 byte missing)
After a couple of tests, it truns out that 1 usec is good enough.
This workaround should be applied to all hardware revisions.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
Since hardware revision 1.11.0, the following interrupt status
registers are now W1C (i.e., write 1 clear):
1. Interrupt Source Group 0 Register (0x144) (EP0 Abort: BIT5)
2. Interrupt Source Group 2 Register (0x14C) (All bits)
And before revision 1.11.0, these registers are all R/W.
Which means software must write a 0 to clear the status.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
Include "mx6_common.h" so that some ARM errata are applied and also the
vddsoc regulator can be changed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Commit 762a88ccf8 introduces
a 64-bit division without using the lldiv() function,
which pulls in previously unused libgcc stuff.
Signed-off-by: Måns Rullgård <mans@mansr.com>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Change the default environment to use zImage instead of uImage, this
requires changes to the default environment to load a file named
zImage instead of uImage, and to use the 'bootz' command instead of
'bootm' when booting the kernel.
The zImage works for FSL Linux's kernel fork versions 3.0.35, 3.10.9,
and 3.10.17; this also works fine for mainline kernels.
Signed-off-by: John Weber <rjohnweber@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
A new 'update_emmc_firmware' target is added to allow for easy U-Boot
update in the eMMC as it has secury boot partition and this needs
specific handling on how to program the specific partition.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
There is no need to print an error message when cpu_eth_init() fails because
net/eth.c already prints it.
In order to simplify the code, just return the value from cpu_eth_init(bis)
directly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This fixes the following compiler warnings:
fti2c010.c: In function 'fti2c010_read':
fti2c010.c:204:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
fti2c010.c: In function 'fti2c010_write':
fti2c010.c:266:8: warning: 'paddr' may be used uninitialized in this function [-Wuninitialized]
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
Cc: Heiko Schocher <hs@denx.de>
Since we agreed on legacy implementation of "eeprom_{read|write}"
(http://patchwork.ozlabs.org/patch/295825/) I had to fix/make it work
again DesignWare I2C driver for cases when 1 EEPROM IC fake I2C with
anumber of "built-in" ICs with different chip addresses.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
cc: Armando Visconti <armando.visconti@st.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin KUMAR <vipin.kumar@st.com>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Kuo-Jung Su <dantesu@faraday-tech.com>
This corrects i2c core to interpret the value returned by
i2c_set_bus_speed as a success indicator rather than the
actual speed that was set. When i2c_set_bus_speed returns
a failure code, the speed is unknown so the adapter speed
is set to zero.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Reviewed-by: Tim Kryger <tim.kryger@linaro.org>
Reviewed-by: Steve Rae <srae@broadcom.com>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>